+----------------------------------+ | ECS4110-24T/24P/28T, ECS3510-26P | +----------------------------------+ "ECS4110-24T_Op_V.bix" is a universal opcode shared among ECS4110-24T, ECS4110-24P, ECS4110-28T, and ECS3510-26P. Their common PID and individual BIDs are listed below. PID = 431 BID = ECS4110-24T: 2, ECS4110-24P: 3, ECS4110-28T: 4, ECS3510-26P: 1 V1.0.0.0 (Build 2013/08/09) --------------------------- This release particularly fixes 3* Diag issues and 1* Loader issue, as reported by RD-TA (Test Program) in ES3526MA-HPoE-FLF-EC device. The issue fixes result in code upgrade - Runtime V1.0.0.0 and Loader V0.0.0.4. Though SW Version is upgraded, it affects several MFG test items in Diag/Loader backdoor commands, but not any function at runtime.. ES3526MA-HPoE-7LF-EC-00004 (Loader)The fan status on bootloader backdoor is not correct for "not good" since it is observed to operate normally. ES3526MA-HPoE-7LF-EC-00005 (Diag)"shportinfo" gives incorrect Port Link Status after "lextlb" is executed. ES3526MA-HPoE-7LF-EC-00006 (Diag)"intlb" would probably get to pakcet loss if loopback cables are connected. ES3526MA-HPoE-7LF-EC-00012 (Diag)"lextlb" would misjudge SFP Test Pass for 1000T/SFP ComboG port when only copper cable connection and no fiber link. V0.0.1.0 (Build 2013/05/02) --------------------------- ES4528MA-7LF-EC-00013 TACACS: No accounting packet is sent from the switch while operating on the console. ES4528MA-7LF-EC-00016 RFE: VLAN ACL (MAC ACL is bound to Interface Ethernet configuration. VLAN ACL is a kind of MAC ACL, however, it is bound to Global configuration.) ES3526MA-HPoE-7LF-EC-00003 insert SFP transceiver will have error messages - specfic to Agilent HFBR-5710LP ES3526MA-HPoE-7LF-EC-00007 console speed default should set to 115200 bps (Also fixed is a factory default "Address Mode" issue*, say "not specified" -> "DHCP".) ES4528MA-7LF-EC-00014 QoS base on CoS result not good for 1000full speed-duplex => Faulty Report... Nothing to Modify (no EPR_ID) MAC ACL and IP ACL cannot be matched at a time. It will be effective for the one being configured first. => Chip limitation... No Fix V0.0.0.5 (Build 2013/03/04) (Cancelled Build 2013/02/27) --------------------------- ES4528MA-7LF-EC-00010 mac-vlan can't work correclty with DHCP snooping ES4528MA-7LF-EC-00012 With a cable connection to copper port 21~24 , its Link Status stays Down ES3526MA-HPoE-7LF-EC-00001 (Enhance)Define ECS3510-26P MIB OID: 1.3.6.1.4.1.259.10.1.38.104 ES3526MA-HPoE-7LF-EC-00002 [Enhancement]Update login prompt to "User Access Verification" ES4528MA-7LF-EC-00013 no accouting packet sent from switch ES4528MA-7LF-EC-00014 QoS base on CoS result not good for 1000full speed-duplex V0.0.0.4 (Build 2013/01/17) --------------------------- ES4528MA-7LF-EC-00007 There is no entry in MVR group member ES4528MA-7LF-EC-00008 client still can receive the multicast stream out of the range ES4528MA-7LF-EC-00009 show interfaces counters on trunk port have problem ES4528MA-7LF-EC-00011 web authentication's function show IPECS logo on web ui ES4528MA-7LF-EC-00010 mac-vlan can't work correclty with DHCP snooping ES4528MA-7LF-EC-00012 With a cable connection to copper port 21~24 , its Link Status stays Down V0.0.0.3 (Build 2012/12/28) --------------------------- ES4528MA-FLF-EC-00002 HW & SW design change to support SFP Port LED light in green blinking when the port is linkup and traffic switching. ES4528MA-FLF-EC-00003 FXC5352(ES4552MA)BugList#16 Http and HTTPS can't be enabled at the same time ES4528MA-FLF-EC-00004 show ip interface - change "via" back to "bia" ES4528MA-FLF-EC-00005 bootup should use DHCP ES4528MA-7LF-EC-00006 can't set trunk on port27,28 V0.0.0.2 (Build 2012/12/10) --------------------------- 1st version that supports 25~28 SFP Port. This version does not support 25~28 SFP Port LED lighting in green blinking (as port linkup and traffic switching). V0.0.0.1 (Build 2012/11/20) --------------------------- 1st version for customization. This version does not support 25~28 SFP Port actually.