ECS4620-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32, Counter32, IpAddress, NOTIFICATION-TYPE, enterprises, TimeTicks, Counter64, Gauge32 FROM SNMPv2-SMI DisplayString, RowStatus, TruthValue, MacAddress, TEXTUAL-CONVENTION FROM SNMPv2-TC PortList, VlanIndex, VlanId, dot1qVlanStaticEntry FROM Q-BRIDGE-MIB InetAddressType, InetAddress, InetAddressIPv6, InetAddressPrefixLength FROM INET-ADDRESS-MIB InterfaceIndex, ifIndex, ifOperStatus FROM IF-MIB EnabledStatus FROM P-BRIDGE-MIB BridgeId, Timeout, dot1dStpPort,dot1dStpPortEntry FROM BRIDGE-MIB pethPsePortEntry, pethMainPseEntry FROM POWER-ETHERNET-MIB Dot1agCfmMepId, dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, dot1agCfmMepIdentifier, dot1agCfmMepDbRMepIdentifier FROM IEEE8021-CFM-MIB dot1xAuthConfigEntry FROM IEEE8021-PAE-MIB TOSType,Metric FROM OSPF-MIB; ecs4620MIB MODULE-IDENTITY LAST-UPDATED "201605160000Z" ORGANIZATION "Edgecore Networks, Inc." CONTACT-INFO "Edgecore Networks, Inc. Customer Service Postal: No. 1 Creation Rd. III, Science-based Industrial Park, Hsinchu 300-77, Taiwan, R.O.C. Tel: +886-3-5770270 Fax: +886-3-5780764 E-mail: support@edge-core.com company website:www.edge-core.com technical support:support@edge-core.com " DESCRIPTION "The MIB module for ECS4620-28T." REVISION "201605160000Z" DESCRIPTION "The current version of this MIB." ::= { edgeCoreNetworksMgt 41 } accton OBJECT IDENTIFIER ::= { enterprises 259 } edgecorenetworks OBJECT IDENTIFIER ::= { accton 10 } edgeCoreNetworksMgt OBJECT IDENTIFIER ::= { edgecorenetworks 1 } ecs4620MIBObjects OBJECT IDENTIFIER ::= { ecs4620MIB 1 } ecs4620Notifications OBJECT IDENTIFIER ::= { ecs4620MIB 2 } --supported groups switchMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 1 } portMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 2 } trunkMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 3 } lacpMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 4 } staMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 5 } restartMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 7 } mirrorMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 8 } igmpSnoopMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 9 } ipMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 10 } vlanMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 12 } priorityMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 13 } trapDestMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 14 } qosMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 16 } securityMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 17 } layer3Mgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 18 } sysLogMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 19 } lineMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 20 } sysTimeMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 23 } fileMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 24 } dnsMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 26 } poeMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 28 } stormMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 33 } sysResourceMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 39 } mvrMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 44 } dhcpSnoopMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 46 } clusterMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 47 } ipSrcGuardMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 48 } upnpMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 49 } oamMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 52 } mldSnoopMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 54 } dynamicArpInspectionMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 56 } udpHelperMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 58 } pppoeiaMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 60 } timeRangeMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 61 } erpsMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 62 } lbdMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 63 } mvr6Mgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 66 } ipv6RaGuardMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 67 } udldMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 69 } dhcpv6SnoopMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 71 } ip6SrcGuardMgt OBJECT IDENTIFIER ::= { ecs4620MIBObjects 74 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- -- The Area ID, in OSPF, has the same format as an IP Address, -- but has the function of defining a summarization point for -- Link State Advertisements AreaID ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An OSPF Area Identifier." SYNTAX IpAddress -- The Router ID, in OSPF, has the same format as an IP Address, -- but identifies the router independent of its IP Address. RouterID ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A OSPF Router Identifier." SYNTAX IpAddress -- The OSPF Metric is defined as an unsigned value in the range BigMetric ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The OSPF External Metric." SYNTAX Integer32 (0..'FFFFFF'h) OspfAuthenticationType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The authentication type." SYNTAX INTEGER { none (0), simplePassword (1), md5 (2) -- reserved for specification by IANA (> 2) } -- Status Values Status ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The status of an interface: 'enabled' indicates that it is willing to communicate with other OSPF Routers, while 'disabled' indicates that it is not." SYNTAX INTEGER { enabled (1), disabled (2) } -- Time Durations measured in seconds PositiveInteger ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A positive integer. Values in excess are precluded as unnecessary and prone to interoperability issues." SYNTAX Integer32 (0..'7FFFFFFF'h) HelloRange ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The range of intervals on which hello messages are exchanged." SYNTAX Integer32 (1..'FFFF'h) UpToMaxAge ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The values that one might find or configure for variables bounded by the maximum age of an LSA." SYNTAX Integer32 (0..3600) -- Potential Priorities for the Designated Router Election DesignatedRouterPriority ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The values defined for the priority of a system for becoming the designated router." SYNTAX Integer32 (0..'FF'h) KeySegment ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The total length of the key is 1024 characters, it is divided into 8 parts and stored in 8 separated mib variables as below: Key1: part 1 of the key (1-128) Key2: part 2 of the key (129-256) Key3: part 3 of the key (257-384) Key4: part 4 of the key (385-512) Key5: part 5 of the key (513-640) Key6: part 6 of the key (641-768) Key7: part 7 of the key (769-896) Key8: part 8 of the key (897-1024) Please note that if the key string is less then 1024 characters, the remaining part of the string will be filled by a zero-length string. For example, if the length of the key is 129, we will get a string of length 128 in Key1, and a string of length 1 in Key2, moreover, Key3 to Key8 will all be zero-length strings." SYNTAX OCTET STRING (SIZE(0..128)) ValidStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A simple status value for the object to create and destroy a table entry. This is a simplified variant of RowStatus as it supports only two values. Setting it to valid(1) creates an entry. Setting it to invalid(2) destroys an entry." SYNTAX INTEGER { valid(1), invalid(2) } StaPathCostMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The path cost mode of a spanning tree algorithm, short(1) indicates that we retrieve/configure the spanning tree path cost as a 16 bit value and long(2) indicates that we retrieve/configure the spanning tree path cost as a 32 bit value." SYNTAX INTEGER { short(1), long(2) } -- -- switchMgt -- -- Management for the switch system, or individual units -- in a stackable switch system. For a non-stackable system, -- only unit 1 exists. switchNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of switches present on this system." ::= { switchMgt 2 } switchInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF SwitchInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and status information about the switch units in this system." ::= { switchMgt 3 } switchInfoEntry OBJECT-TYPE SYNTAX SwitchInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table providing descriptions and status information for switch units." INDEX { swUnitIndex } ::= { switchInfoTable 1 } SwitchInfoEntry ::= SEQUENCE { swUnitIndex Integer32, swHardwareVer DisplayString, swMicrocodeVer DisplayString, swLoaderVer DisplayString, swBootRomVer DisplayString, swOpCodeVer DisplayString, swPortNumber Integer32, swPowerStatus INTEGER, swRoleInSystem INTEGER, swSerialNumber DisplayString, swServiceTag DisplayString, swModelNumber DisplayString, swEpldVer DisplayString } swUnitIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber." ::= { switchInfoEntry 1 } swHardwareVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Hardware version of the main board." ::= { switchInfoEntry 2 } swMicrocodeVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Microcode version of the main board." ::= { switchInfoEntry 3 } swLoaderVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Loader version of the main board." ::= { switchInfoEntry 4 } swBootRomVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Boot ROM code version of the main board." ::= { switchInfoEntry 5 } swOpCodeVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Operation code version of the main board." ::= { switchInfoEntry 6 } swPortNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ports on this switch." ::= { switchInfoEntry 7 } swPowerStatus OBJECT-TYPE SYNTAX INTEGER { internalPower(1), redundantPower(2), internalAndRedundantPower(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the switch using internalPower(1), redundantPower(2) or both(3)" ::= { switchInfoEntry 8 } swRoleInSystem OBJECT-TYPE SYNTAX INTEGER { master(1), backupMaster(2), slave(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the switch is master(1), backupMaster(2) or slave(3) in this system." ::= { switchInfoEntry 9 } swSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the switch." ::= { switchInfoEntry 10 } swServiceTag OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Service tag serial-number of the switch." ::= { switchInfoEntry 13 } swModelNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "Model number of the switch." ::= { switchInfoEntry 14 } swEpldVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The EPLD version of the switch." ::= { switchInfoEntry 15 } switchOperState OBJECT-TYPE SYNTAX INTEGER { other(1), unknown(2), ok(3), noncritical(4), critical(5), nonrecoverable(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Global operation state of the switch." ::= { switchMgt 4 } switchProductId OBJECT IDENTIFIER ::= { switchMgt 5 } swProdName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The product name of this switch." ::= { switchProductId 1 } swProdManufacturer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The product manufacturer of this switch." ::= { switchProductId 2 } swProdDescription OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The product description of this switch." ::= { switchProductId 3 } swProdVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The runtime code version of this switch." ::= { switchProductId 4 } swProdUrl OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The URL of this switch, which we can connect through a web browser." ::= { switchProductId 5 } swIdentifier OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A unique identifier of which switch in the chassis is currently being looked at." ::= { switchProductId 6 } swChassisServiceTag OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "The service tag of the chassis this switch resides in." ::= { switchProductId 7 } switchIndivPowerTable OBJECT-TYPE SYNTAX SEQUENCE OF SwitchIndivPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table about the status of individual powers." ::= { switchMgt 6 } switchIndivPowerEntry OBJECT-TYPE SYNTAX SwitchIndivPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table about the status of individual power." INDEX { swIndivPowerUnitIndex, swIndivPowerIndex } ::= { switchIndivPowerTable 1 } SwitchIndivPowerEntry ::= SEQUENCE { swIndivPowerUnitIndex Integer32, swIndivPowerIndex INTEGER, swIndivPowerStatus INTEGER } swIndivPowerUnitIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This is defined as swUnitIndex." ::= { switchIndivPowerEntry 1 } swIndivPowerIndex OBJECT-TYPE SYNTAX INTEGER { internalPower(1), externalPower(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "1 means internal power, 2 means external power." ::= { switchIndivPowerEntry 2 } swIndivPowerStatus OBJECT-TYPE SYNTAX INTEGER { notPresent(1), green(2), red(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "notPresent(1) means not present, green(2) means up, red(3) means down." ::= { switchIndivPowerEntry 3 } switchJumboFrameStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "enable(1) means the Jumbo Frame has enabled, disabled(2) means the Jumbo Frame has disabled." ::= { switchMgt 7 } amtrMgt OBJECT IDENTIFIER ::= { switchMgt 8 } --switchFanTable switchFanTable OBJECT-TYPE SYNTAX SEQUENCE OF SwitchFanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The fan status table." ::= { switchMgt 9 } switchFanEntry OBJECT-TYPE SYNTAX SwitchFanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the switchFanTable." INDEX { switchUnitIndex, switchFanIndex } ::= { switchFanTable 1 } SwitchFanEntry ::= SEQUENCE { switchUnitIndex Integer32, switchFanIndex Integer32, switchFanStatus INTEGER, switchFanOperSpeed Integer32 } switchUnitIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The unit of the switch for the stackable device." ::= { switchFanEntry 1 } switchFanIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The unit number of the fan." ::= { switchFanEntry 2 } switchFanStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), failure(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicating the status of the fan, 1:ok; 2:failure." ::= { switchFanEntry 3 } switchFanOperSpeed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The operational value of the fan speed, measured in rpm (rotations per minute)." ::= { switchFanEntry 6 } -- switchThermalTempTable switchThermalTempTable OBJECT-TYPE SYNTAX SEQUENCE OF SwitchThermalTempEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table which collects switch temperature information." ::= { switchMgt 11 } switchThermalTempEntry OBJECT-TYPE SYNTAX SwitchThermalTempEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the switchThermalTempTable." INDEX { switchThermalTempUnitIndex,switchThermalTempThermalIndex} ::= { switchThermalTempTable 1 } SwitchThermalTempEntry ::= SEQUENCE { switchThermalTempUnitIndex Integer32, switchThermalTempThermalIndex Integer32, switchThermalTempValue Integer32 } switchThermalTempUnitIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The unit of the switch for stackable device." ::= { switchThermalTempEntry 1 } switchThermalTempThermalIndex OBJECT-TYPE SYNTAX Integer32(1..3) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The thermal index of the switch." ::= { switchThermalTempEntry 2 } switchThermalTempValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature of the device in degrees Celsius." ::= { switchThermalTempEntry 3 } --switchThermalActionTable switchThermalActionTable OBJECT-TYPE SYNTAX SEQUENCE OF SwitchThermalActionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the thermal action." ::= { switchMgt 12 } switchThermalActionEntry OBJECT-TYPE SYNTAX SwitchThermalActionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the switchThermalActionTable." INDEX { switchThermalActionUnitIndex,switchThermalActionThermalIndex, switchThermalActionIndex } ::= { switchThermalActionTable 1 } SwitchThermalActionEntry ::= SEQUENCE { switchThermalActionUnitIndex Integer32, switchThermalActionThermalIndex Integer32, switchThermalActionIndex Integer32, switchThermalActionRisingThreshold Integer32, switchThermalActionFallingThreshold Integer32, switchThermalActionAction BITS, switchThermalActionStatus ValidStatus } switchThermalActionUnitIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The unit of the switch for stackable device." ::= { switchThermalActionEntry 1 } switchThermalActionThermalIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The thermal index of the switch." ::= { switchThermalActionEntry 2 } switchThermalActionIndex OBJECT-TYPE SYNTAX Integer32(1) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The action index of the switchTheramlActionTable." ::= { switchThermalActionEntry 3 } switchThermalActionRisingThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The rising threshold of the switch temperature." ::= { switchThermalActionEntry 4 } switchThermalActionFallingThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The falling threshold of the switch temperature." ::= { switchThermalActionEntry 5 } switchThermalActionAction OBJECT-TYPE SYNTAX BITS { trap(0) } MAX-ACCESS read-create STATUS current DESCRIPTION "The action that will be taken when the temperature exceeds the rising threshold or falls below the falling threshold." ::= { switchThermalActionEntry 6 } switchThermalActionStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set valid(1) to create an entry, Set Invalid(2) to delete an entry." ::= { switchThermalActionEntry 7 } -- Address Management amtrMacAddrAgingStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "If this is enabled(1), the MAC address table will age out according to its timer. If this is disabled(2), the MAC address table will not age out." ::= { amtrMgt 3 } switchRenumberUnitID OBJECT-TYPE SYNTAX INTEGER { renumber(1), noRenumber(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The value renumber will automatically assign an ID to units in the stack; all UNIT IDs will be contiguous. The system configurations are not changed but the system will restart after renumbering is completed." ::= { switchMgt 14 } switchStackingTable OBJECT-TYPE SYNTAX SEQUENCE OF SwitchStackingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and status information describing the configuration of stacking system." ::= { switchMgt 23 } switchStackingEntry OBJECT-TYPE SYNTAX SwitchStackingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, describing the configuration of stacking system of one unit." INDEX { swStackingUnitIndex } ::= { switchStackingTable 1 } SwitchStackingEntry ::= SEQUENCE { swStackingUnitIndex Integer32, swActiveStackingButton INTEGER, swActiveStackingPortOption INTEGER, swConfigStackingButton INTEGER, swMasterButton INTEGER, swConfigStackingPortOption INTEGER } swStackingUnitIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the switch within the system for which this entry contains information." ::= { switchStackingEntry 1 } swActiveStackingButton OBJECT-TYPE SYNTAX INTEGER { notPressed(0), pressed(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the active status of stacking button of the switch." ::= { switchStackingEntry 2 } swConfigStackingButton OBJECT-TYPE SYNTAX INTEGER { notPressed(0), pressed(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the configured status of stacking button of the switch." ::= { switchStackingEntry 3 } swMasterButton OBJECT-TYPE SYNTAX INTEGER { notPressed(0), pressed(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the master button status of the switch." ::= { switchStackingEntry 4 } swActiveStackingPortOption OBJECT-TYPE SYNTAX INTEGER { firstOption(1), secondOption(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the active option status of stacking port of the switch." ::= { switchStackingEntry 5 } swConfigStackingPortOption OBJECT-TYPE SYNTAX INTEGER { firstOption(1), secondOption(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the configured option status of stacking port of the switch." ::= { switchStackingEntry 6 } -- -- portMgt -- -- Management ports. This group also provides information -- related to trunks because they share the same properties. portTable OBJECT-TYPE SYNTAX SEQUENCE OF PortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and status information describing the configuration of each switch port. This table also contains information about each trunk." ::= { portMgt 1 } portEntry OBJECT-TYPE SYNTAX PortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, describing the configuration of one switch port or trunk." INDEX { portIndex } ::= { portTable 1 } PortEntry ::= SEQUENCE { portIndex InterfaceIndex, portName DisplayString, portType INTEGER, portSpeedDpxCfg INTEGER, portFlowCtrlCfg INTEGER, portCapabilities BITS, portAutonegotiation EnabledStatus, portSpeedDpxStatus INTEGER, portFlowCtrlStatus INTEGER, portTrunkIndex Integer32, portComboForcedMode INTEGER, portMasterSlaveModeCfg INTEGER, portMacAddrLearningStatus EnabledStatus, portMacAddrLearningCount Counter32 } portIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { portEntry 1 } portName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later)." ::= { portEntry 2 } portType OBJECT-TYPE SYNTAX INTEGER { other(1), hundredBaseTX(2), hundredBaseFX(3), thousandBaseSX(4), thousandBaseLX(5), thousandBaseT(6), thousandBaseGBIC(7), thousandBaseSfp(8), hundredBaseFxScSingleMode(9), hundredBaseFxScMultiMode(10), thousandBaseCX(11), tenG(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the port type of the configuration of the switch." ::= { portEntry 3 } portSpeedDpxCfg OBJECT-TYPE SYNTAX INTEGER { reserved(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7), halfDuplex10g(8), fullDuplex10g(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode halfDuplex10g(8) - 10g and half duplex mode fullDuplex10g(9) - 10g and full duplex mode hundredBaseTX port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as: fullDuplex100(5) thousandBaseSX port can be set as: fullDuplex1000(7) thousandBaseLX port can be set as: fullDuplex1000(7) thousandBaseT port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) thousandBaseGBIC port can be set as: fullDuplex1000(7) thousandBaseSfp port can be set as: fullDuplex1000(7) hundredBaseFxScSingleMode port can be set as: fullDuplex100(5) hundredBaseFxScMultiMode port can be set as: fullDuplex100(5) thousandBaseCX port can be set as: fullDuplex1000(7) tenG port can be set as: halfDuplex10g(8) fullDuplex10g(9) The actual operating speed and duplex of the port is given by portSpeedDpxStatus." DEFVAL { halfDuplex10 } ::= { portEntry 4 } portFlowCtrlCfg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), tx(5), rx(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "(1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (5) Flow control mechanism is enabled with tx pause mechanism only. (6) Flow control mechansim is enabled with rx pause mechansim only. Fast ethernet ports can be set as: enabled(1), disabled(2). Gigabit ethernet ports can be set as: enabled(1), disabled(2), tx(5), rx(6). The actual flow control mechanism is used given by portFlowCtrlStatus." DEFVAL { disabled } ::= { portEntry 5 } portCapabilities OBJECT-TYPE SYNTAX BITS { portCap10half(0), portCap10full(1), portCap100half(2), portCap100full(3), portCap1000half(4), portCap1000full(5), portCap10gHalf(6), portCap10gFull(7), reserved8(8), reserved9(9), reserved10(10), reserved11(11), reserved12(12), reserved13(13), portCapSym(14), portCapFlowCtrl(15) } MAX-ACCESS read-write STATUS current DESCRIPTION "Port or trunk capabilities." ::= { portEntry 6 } portAutonegotiation OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether auto-negotiation is enabled." ::= { portEntry 7 } portSpeedDpxStatus OBJECT-TYPE SYNTAX INTEGER { error(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7), halfDuplex10g(8), fullDuplex10g(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case the value is error(1)." ::= { portEntry 8 } portFlowCtrlStatus OBJECT-TYPE SYNTAX INTEGER { error(1), backPressure(2), dot3xFlowControl(3), none(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "(2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently configured then this value is error(1)." ::= { portEntry 9 } portTrunkIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding trunkPorts." ::= { portEntry 10 } portComboForcedMode OBJECT-TYPE SYNTAX INTEGER { none(1), copperForced(2), copperPreferredAuto(3), sfpForced(4), sfpPreferredAuto(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal to none(1), and setting this variable to none(1) is not allowed. copperForced(2) is set if user want to force this combo port running in copper mode. copperPreferredAuto(3) is obsoleted, and user shall not set this state. sfpForced(4) is set if user want to force this combo port running in fiber mode. sfpPreferredAuto(5) is set if user want to change copper or fiber mode automatically by SFP transceiver present state. If SFP transceiver is present, this combo port will run in fiber mode, and if SFP transceiver is not present, this combo port will run in copper mode." ::= { portEntry 12} portMasterSlaveModeCfg OBJECT-TYPE SYNTAX INTEGER { master(1), slave(2), auto(3), autoPreferMaster(4), autoPreferSlave(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port." ::= { portEntry 15 } portMacAddrLearningStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set this variable to enabled(1) to start to learn MAC addresses. Set this variable to disabled(2) to stop to learn MAC addresses." DEFVAL { enabled } ::= { portEntry 17 } portMacAddrLearningCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of learned MAC addresses." ::= { portEntry 18 } -- -- cable diagnostics -- cableDiagMgt OBJECT IDENTIFIER ::= { portMgt 3 } cableDiagCtlAction OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "To execute cable diagnostics on a port, assign cableDiagCtlAction to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0." ::= { cableDiagMgt 1 } cableDiagResultTable OBJECT-TYPE SYNTAX SEQUENCE OF CableDiagResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for cable diagnostics result." ::= { cableDiagMgt 2 } cableDiagResultEntry OBJECT-TYPE SYNTAX CableDiagResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for cable diagnostics result." INDEX { cableDiagResultIfIndex } ::= { cableDiagResultTable 1 } CableDiagResultEntry ::= SEQUENCE { cableDiagResultIfIndex InterfaceIndex, cableDiagResultStatusPairA INTEGER, cableDiagResultStatusPairB INTEGER, cableDiagResultStatusPairC INTEGER, cableDiagResultStatusPairD INTEGER, cableDiagResultDistancePairA Integer32, cableDiagResultDistancePairB Integer32, cableDiagResultDistancePairC Integer32, cableDiagResultDistancePairD Integer32, cableDiagResultTime DisplayString } cableDiagResultIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as the ifIndex." ::= { cableDiagResultEntry 1 } cableDiagResultStatusPairA OBJECT-TYPE SYNTAX INTEGER { notTestedYet(1), ok(2), open(3), short(4), unknown(7), impedanceMismatch(8), failed(9), notSupported(10), noCable(11), underTesting(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable. Value underTesting(12) means cable diag is still running. Value unknown(7) means pair has an error matching none of the above." ::= { cableDiagResultEntry 2 } cableDiagResultStatusPairB OBJECT-TYPE SYNTAX INTEGER { notTestedYet(1), ok(2), open(3), short(4), unknown(7), impedanceMismatch(8), failed(9), notSupported(10), noCable(11), underTesting(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable. Value underTesting(12) means cable diag is still running. Value unknown(7) means pair has an error matching none of the above." ::= { cableDiagResultEntry 3 } cableDiagResultStatusPairC OBJECT-TYPE SYNTAX INTEGER { notTestedYet(1), ok(2), open(3), short(4), unknown(7), impedanceMismatch(8), failed(9), notSupported(10), noCable(11), underTesting(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable. Value underTesting(12) means cable diag is still running. Value unknown(7) means pair has an error matching none of the above." ::= { cableDiagResultEntry 4 } cableDiagResultStatusPairD OBJECT-TYPE SYNTAX INTEGER { notTestedYet(1), ok(2), open(3), short(4), unknown(7), impedanceMismatch(8), failed(9), notSupported(10), noCable(11), underTesting(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable. Value underTesting(12) means cable diag is still running. Value unknown(7) means pair has an error matching none of the above." ::= { cableDiagResultEntry 5 } cableDiagResultDistancePairA OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the fault distance of pair A of the cable in meters. 0 will be displayed if cableDiagResultStatusPairA equals to Value underTesting(12)." ::= { cableDiagResultEntry 6 } cableDiagResultDistancePairB OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the fault distance of pair B of the cable in meters. 0 will be displayed if cableDiagResultStatusPairB equals to Value underTesting(12)." ::= { cableDiagResultEntry 7 } cableDiagResultDistancePairC OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the fault distance of pair C of the cable in meters. 0 will be displayed if cableDiagResultStatusPairC equals to Value underTesting(12)." ::= { cableDiagResultEntry 8 } cableDiagResultDistancePairD OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the fault distance of pair D of the cable in meters. 0 will be displayed if cableDiagResultStatusPairD equals to Value underTesting(12)." ::= { cableDiagResultEntry 9 } cableDiagResultTime OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the last time of cable diagnostics. For example, 'Jan 1 02:03:04 2002'." ::= { cableDiagResultEntry 11 } -- -- loopback -- loopbackTestMgt OBJECT IDENTIFIER ::= { portMgt 4 } loopInternalCtlAction OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "To execute internal loopback test on a port, assign loopInternalCtlAction to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0." ::= { loopbackTestMgt 1 } loopInternalResultTable OBJECT-TYPE SYNTAX SEQUENCE OF LoopInternalResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for internal loopback test result." ::= { loopbackTestMgt 2 } loopInternalResultEntry OBJECT-TYPE SYNTAX LoopInternalResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for internal loopback test result." INDEX { loopInternalResultIfIndex } ::= { loopInternalResultTable 1 } LoopInternalResultEntry ::= SEQUENCE { loopInternalResultIfIndex InterfaceIndex, loopInternalResultStatus INTEGER, loopInternalResultTime DisplayString } loopInternalResultIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as the ifIndex." ::= { loopInternalResultEntry 1 } loopInternalResultStatus OBJECT-TYPE SYNTAX INTEGER { notTestedYet(1), succeeded(2), failed(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of internal loopback." ::= { loopInternalResultEntry 2 } loopInternalResultTime OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the last time of internal loopback. For example, 'Jan 1 02:03:04 2002'." ::= { loopInternalResultEntry 3 } portUtilTable OBJECT-TYPE SYNTAX SEQUENCE OF PortUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Dispalys port utilization during recent 300 seconds." ::= { portMgt 6 } portUtilEntry OBJECT-TYPE SYNTAX PortUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Dispalys port utilization during recent 300 seconds." INDEX { portUtilIfIndex } ::= { portUtilTable 1 } PortUtilEntry ::= SEQUENCE { portUtilIfIndex InterfaceIndex, portInOctetRate Counter64, portInPacketRate Counter64, portInUtil Integer32, portOutOctetRate Counter64, portOutPacketRate Counter64, portOutUtil Integer32 } portUtilIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and trunk interface of the portUtilTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { portUtilEntry 1 } portInOctetRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The input octet rate (kbits/sec) of the port." ::= { portUtilEntry 2 } portInPacketRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The input packet rate (pkts/sec) of the port." ::= { portUtilEntry 3 } portInUtil OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The input utilization of the port, in one per hundred." ::= { portUtilEntry 4 } portOutOctetRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The output octet rate (kbits/sec) of the port." ::= { portUtilEntry 5 } portOutPacketRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The output packet rate (pkts/sec) of the port." ::= { portUtilEntry 6 } portOutUtil OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The output utilization of the port, in one per hundred." ::= { portUtilEntry 7 } portVlanTrunkingTable OBJECT-TYPE SYNTAX SEQUENCE OF PortVlanTrunkingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configures vlan trunking feature." ::= { portMgt 7 } portVlanTrunkingEntry OBJECT-TYPE SYNTAX PortVlanTrunkingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configures vlan trunking feature." INDEX { portVlanTrunkingIfIndex } ::= { portVlanTrunkingTable 1 } PortVlanTrunkingEntry ::= SEQUENCE { portVlanTrunkingIfIndex InterfaceIndex, portVlanTrunkingStatus EnabledStatus } portVlanTrunkingIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and trunk interface of the portVlanTrunkingTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { portVlanTrunkingEntry 1 } portVlanTrunkingStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether vlan trunking is enabled." ::= { portVlanTrunkingEntry 2 } -- -- Show Media Information -- Information of the media device installed in the physical ports. -- portMediaInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF PortMediaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table lists the information of the media device (SFP/XFP/Copper) installed in the physical port. Only the ifIndices of Ethernet ports those are associated with the operational cards will be included in this table." ::= { portMgt 10 } portMediaInfoEntry OBJECT-TYPE SYNTAX PortMediaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the Interface Media Information table. The ifIndices of ethernet interfaces will be used to index this table." INDEX { portMediaInfoIfIndex } ::= { portMediaInfoTable 1 } PortMediaInfoEntry ::= SEQUENCE { portMediaInfoIfIndex InterfaceIndex, portMediaInfoConnectorType DisplayString, portMediaInfoFiberType DisplayString, portMediaInfoEthComplianceCodes DisplayString, portMediaInfoBaudRate DisplayString, portMediaInfoVendorOUI DisplayString, portMediaInfoVendorName DisplayString, portMediaInfoPartNumber DisplayString, portMediaInfoRevision DisplayString, portMediaInfoSerialNumber DisplayString, portMediaInfoDateCode DisplayString } portMediaInfoIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "ifindex." ::= { portMediaInfoEntry 1 } portMediaInfoConnectorType OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The connector type." ::= { portMediaInfoEntry 2 } portMediaInfoFiberType OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The fiber type." ::= { portMediaInfoEntry 3 } portMediaInfoEthComplianceCodes OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ethernet compliance codes." ::= { portMediaInfoEntry 4 } portMediaInfoBaudRate OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The baud rate." ::= { portMediaInfoEntry 5 } portMediaInfoVendorOUI OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The OUI of the vendor." ::= { portMediaInfoEntry 6 } portMediaInfoVendorName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The media vendor name, full name of the corporation." ::= { portMediaInfoEntry 7 } portMediaInfoPartNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The media vendor part number." ::= { portMediaInfoEntry 8 } portMediaInfoRevision OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The media vendor product version number." ::= { portMediaInfoEntry 9 } portMediaInfoSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor serial number of the media device." ::= { portMediaInfoEntry 10 } portMediaInfoDateCode OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The date code of the media device." ::= { portMediaInfoEntry 11 } -- ifIndex to Optical Parameters Table -- Given an ifIndex, this table returns the optical parameters for the ifIndex. portOpticalMonitoringInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF PortOpticalMonitoringInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table lists the instrumented parameters of all optical interfaces." REFERENCE "ITU recommendations G.783, G.784, G.953" ::= { portMgt 11 } portOpticalMonitoringInfoEntry OBJECT-TYPE SYNTAX PortOpticalMonitoringInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Only the ifIndices of optical interfaces whose parameters need to be monitored will be used to index this table." INDEX { portOpticalMonitoringInfoIfIndex } ::= { portOpticalMonitoringInfoTable 1 } PortOpticalMonitoringInfoEntry ::= SEQUENCE { portOpticalMonitoringInfoIfIndex InterfaceIndex, portOpticalMonitoringInfoTemperature DisplayString, portOpticalMonitoringInfoVcc DisplayString, portOpticalMonitoringInfoTxBiasCurrent DisplayString, portOpticalMonitoringInfoTxPower DisplayString, portOpticalMonitoringInfoRxPower DisplayString } portOpticalMonitoringInfoIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "ifindex." ::= { portOpticalMonitoringInfoEntry 1 } portOpticalMonitoringInfoTemperature OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object holds the value of the transmitter laser diode temperature for the interface. This object indicates the health of the transmitter. The format is xxx.yyyy C(elcius). If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning." ::= { portOpticalMonitoringInfoEntry 2 } portOpticalMonitoringInfoVcc OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object holds the value of the Vcc. It is measured in V. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning." ::= { portOpticalMonitoringInfoEntry 3 } portOpticalMonitoringInfoTxBiasCurrent OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Tx Bias Current. It is measured in mA. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning." ::= { portOpticalMonitoringInfoEntry 4 } portOpticalMonitoringInfoTxPower OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object holds the value of the transmitter optical signal power for the interface, measured in dBm. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning." ::= { portOpticalMonitoringInfoEntry 5 } portOpticalMonitoringInfoRxPower OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object holds the value of the receiver optical signal power for the interface, measured in dBm. If the device support ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning." ::= { portOpticalMonitoringInfoEntry 6 } -- -- transceiver threshold -- portTransceiverThresholdInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF PortTransceiverThresholdInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table lists the threshold of transceivers." REFERENCE "ITU recommendations G.783, G.784, G.953" ::= { portMgt 12 } portTransceiverThresholdInfoEntry OBJECT-TYPE SYNTAX PortTransceiverThresholdInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identify the index of the transceiver" INDEX { portTransceiverThresholdInfoIfIndex } ::= { portTransceiverThresholdInfoTable 1 } PortTransceiverThresholdInfoEntry ::= SEQUENCE { portTransceiverThresholdInfoIfIndex InterfaceIndex, portTransceiverThresholdInfoTemperatureLowAlarm Integer32, portTransceiverThresholdInfoTemperatureLowWarn Integer32, portTransceiverThresholdInfoTemperatureHighWarn Integer32, portTransceiverThresholdInfoTemperatureHighAlarm Integer32, portTransceiverThresholdInfoVccLowAlarm Integer32, portTransceiverThresholdInfoVccLowWarn Integer32, portTransceiverThresholdInfoVccHighWarn Integer32, portTransceiverThresholdInfoVccHighAlarm Integer32, portTransceiverThresholdInfoTxBiasCurrentLowAlarm Integer32, portTransceiverThresholdInfoTxBiasCurrentLowWarn Integer32, portTransceiverThresholdInfoTxBiasCurrentHighWarn Integer32, portTransceiverThresholdInfoTxBiasCurrentHighAlarm Integer32, portTransceiverThresholdInfoTxPowerLowAlarm Integer32, portTransceiverThresholdInfoTxPowerLowWarn Integer32, portTransceiverThresholdInfoTxPowerHighWarn Integer32, portTransceiverThresholdInfoTxPowerHighAlarm Integer32, portTransceiverThresholdInfoRxPowerLowAlarm Integer32, portTransceiverThresholdInfoRxPowerLowWarn Integer32, portTransceiverThresholdInfoRxPowerHighWarn Integer32, portTransceiverThresholdInfoRxPowerHighAlarm Integer32, portTransceiverThresholdAutoMode TruthValue } portTransceiverThresholdInfoIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "ifindex." ::= { portTransceiverThresholdInfoEntry 1 } portTransceiverThresholdInfoTemperatureLowAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low alarm threshold of the transmitter laser diode temperature for the interface." ::= { portTransceiverThresholdInfoEntry 2 } portTransceiverThresholdInfoTemperatureLowWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low warning threshold of the transmitter laser diode temperature for the interface." ::= { portTransceiverThresholdInfoEntry 3 } portTransceiverThresholdInfoTemperatureHighWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high warning threshold of the transmitter laser diode temperature for the interface." ::= { portTransceiverThresholdInfoEntry 4 } portTransceiverThresholdInfoTemperatureHighAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high alarm threshold of the transmitter laser diode temperature for the interface." ::= { portTransceiverThresholdInfoEntry 5 } portTransceiverThresholdInfoVccLowAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low alarm threshold of the Vcc." ::= { portTransceiverThresholdInfoEntry 6 } portTransceiverThresholdInfoVccLowWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low warning threshold of the Vcc." ::= { portTransceiverThresholdInfoEntry 7 } portTransceiverThresholdInfoVccHighWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high warning threshold of the Vcc." ::= { portTransceiverThresholdInfoEntry 8 } portTransceiverThresholdInfoVccHighAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high alarm threshold of the Vcc." ::= { portTransceiverThresholdInfoEntry 9 } portTransceiverThresholdInfoTxBiasCurrentLowAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "low alarm threshold of Tx Bias Current." ::= { portTransceiverThresholdInfoEntry 10 } portTransceiverThresholdInfoTxBiasCurrentLowWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "low warning threshold of Tx Bias Current." ::= { portTransceiverThresholdInfoEntry 11 } portTransceiverThresholdInfoTxBiasCurrentHighWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "high warning threshold of Tx Bias Current." ::= { portTransceiverThresholdInfoEntry 12 } portTransceiverThresholdInfoTxBiasCurrentHighAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "high alarm threshold of Tx Bias Current." ::= { portTransceiverThresholdInfoEntry 13 } portTransceiverThresholdInfoTxPowerLowAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low alarm threshold of the transmitter optical signal power for theinterface." ::= { portTransceiverThresholdInfoEntry 14 } portTransceiverThresholdInfoTxPowerLowWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low warning threshold of the transmitter optical signal power for the interface." ::= { portTransceiverThresholdInfoEntry 15 } portTransceiverThresholdInfoTxPowerHighWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high warning threshold of the transmitter optical signal power for the interface." ::= { portTransceiverThresholdInfoEntry 16 } portTransceiverThresholdInfoTxPowerHighAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high alarm threshold of the transmitter optical signal power for the interface." ::= { portTransceiverThresholdInfoEntry 17 } portTransceiverThresholdInfoRxPowerLowAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low alarm threshold of the receiver optical signal power for the interface." ::= { portTransceiverThresholdInfoEntry 18 } portTransceiverThresholdInfoRxPowerLowWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the low warning threshold of the receiver optical signal power for the interface." ::= { portTransceiverThresholdInfoEntry 19 } portTransceiverThresholdInfoRxPowerHighWarn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high warning threshold of the receiver optical signal power for the interface." ::= { portTransceiverThresholdInfoEntry 20 } portTransceiverThresholdInfoRxPowerHighAlarm OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object holds the high alarm threshold of the receiver optical signal power for the interface." ::= { portTransceiverThresholdInfoEntry 21 } portTransceiverThresholdAutoMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate the transceiver threshold is retrieved from EEPROM or configured by user." ::= { portTransceiverThresholdInfoEntry 22 } -- -- trunkMgt -- -- Trunks: Provides additional information for Trunks trunkMaxId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number for a trunk identifier." ::= { trunkMgt 1 } trunkValidNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of valid trunks." ::= { trunkMgt 2 } trunkTable OBJECT-TYPE SYNTAX SEQUENCE OF TrunkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table describing the configuration and status of each trunk." ::= { trunkMgt 3 } trunkEntry OBJECT-TYPE SYNTAX TrunkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing the configuration and status of a particular trunk." INDEX { trunkIndex } ::= { trunkTable 1 } TrunkEntry ::= SEQUENCE { trunkIndex InterfaceIndex, trunkPorts PortList, trunkCreation INTEGER, trunkStatus ValidStatus } trunkIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies the trunk within the switch that is described by the table entry." ::= { trunkEntry 1 } trunkPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The complete set of ports currently associated with this trunk." ::= { trunkEntry 2 } trunkCreation OBJECT-TYPE SYNTAX INTEGER { static(1), lacp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk." ::= { trunkEntry 3 } trunkStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured." ::= { trunkEntry 4 } trunkBalanceMode OBJECT-TYPE SYNTAX INTEGER { macSrc(1), macDst(2), macSrcDst(3), ipSrc(4), ipDst(5), ipSrcDst(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This defines the load balancing mode of trunks in the system. It may be based on source and/or destination MAC address or IP address. macSrc(1) means source MAC address. macDst(2) means destination MAC address. macSrcDst(3) means source and destination MAC address. ipSrc(4) means source IP address. ipDst(5) means destination IP address. ipSrcDst(6) means source and destination IP address." ::= { trunkMgt 4 } -- -- lacpMgt -- -- Management for Link Aggregation Control Protocol (LACP, 802.3ad), -- that is dynamic trunking. lacpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for LACP port configuration." ::= { lacpMgt 1 } lacpPortEntry OBJECT-TYPE SYNTAX LacpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for LACP port configuration. While an entry may exist for a particular port, the port may not support LACP and an attempt to enable LACP may result in failure." INDEX { lacpPortIndex } ::= { lacpPortTable 1 } LacpPortEntry ::= SEQUENCE { lacpPortIndex InterfaceIndex, lacpPortStatus EnabledStatus } lacpPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { lacpPortEntry 1 } lacpPortStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether 802.3ad LACP is enabled." ::= { lacpPortEntry 2 } -- -- staMgt -- -- Management for Spanning Tree Algorithm (STA). -- This has variables not already defined in the implemented -- standard MIB(s). staSystemStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled." DEFVAL { enabled } ::= { staMgt 1 } staPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table manages port settings for Spanning Tree Protocol 802.1d, 802.1w or 802.1s depending on the value specified by staProtocolType." REFERENCE "IEEE 802.1d, IEEE 802.1w, IEEE 802.1s." ::= { staMgt 2 } staPortEntry OBJECT-TYPE SYNTAX StaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual entry of staPortTable." AUGMENTS { dot1dStpPortEntry } ::= { staPortTable 1 } StaPortEntry ::= SEQUENCE { -- for MST, RSTP staPortProtocolMigration TruthValue, staPortOperEdgePort TruthValue, staPortAdminPointToPoint INTEGER, staPortOperPointToPoint TruthValue, staPortSystemStatus EnabledStatus, staPortLongAdminPathCost Integer32, staPortLongOperPathCost Integer32, staPortBpduFlooding EnabledStatus, staPortBpduGuard EnabledStatus, staPortAdminEdgePortWithAuto INTEGER, staPortBpduFilter EnabledStatus, staPortRootGuardStatus EnabledStatus, staPortBpduGuardAutoRecovery EnabledStatus, staPortBpduGuardAutoRecoveryInterval Unsigned32, staPortTcPropStop TruthValue } -- for MST, RSTP staPortProtocolMigration OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read." REFERENCE "IEEE 802.1w clause 14.8.2.4, 17.18.10, 17.26" ::= { staPortEntry 3 } staPortOperEdgePort OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received." REFERENCE "IEEE 802.1t clause 14.8.2, 18.3.4" ::= { staPortEntry 5 } staPortAdminPointToPoint OBJECT-TYPE SYNTAX INTEGER { forceTrue(0), forceFalse(1), auto(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means." REFERENCE "IEEE 802.1w clause 6.4.3, 6.5, 14.8.2" ::= { staPortEntry 6 } staPortOperPointToPoint OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the staPortAdminPointToPoint object." REFERENCE "IEEE 802.1w clause 6.4.3, 6.5, 14.8.2" ::= { staPortEntry 7 } staPortSystemStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled." DEFVAL { enabled } ::= { staPortEntry 9 } staPortLongAdminPathCost OBJECT-TYPE SYNTAX Integer32(0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated. Setting this to 0 means that the path cost is automatically determined. In this case, read staPortLongOperPathCost to get the oper value." ::= { staPortEntry 10 } staPortLongOperPathCost OBJECT-TYPE SYNTAX Integer32(1..200000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated." ::= { staPortEntry 11 } -- BPUD flooding can be configured per port when spanning tree is disable staPortBpduFlooding OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to configure the capability of BPDUs flooding." ::= { staPortEntry 12 } staPortBpduGuard OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "A value of enabled(1) indicates that BPDU port guard feature is enabled for each port. A value of disabled(2) indicates that the feature is disabled." ::= { staPortEntry 15 } staPortAdminEdgePortWithAuto OBJECT-TYPE SYNTAX INTEGER { true(1), false(2), auto(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-port and a value of auot (3) indicates this port in RSPT or MSTP mode should be assumed as an edge-port after migration or max age expire without receiving any BPDU and sending BPDU with proposal flag on." ::= { staPortEntry 16 } staPortBpduFilter OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative value of the BPDU filter parameter. A value of enabled(1) indicates that this port will avoid transmitting BPDUs on edge-port and the value of disabled(2) indicates that this port will not avoid transmitting BPDUs on edge-port." ::= { staPortEntry 17 } staPortRootGuardStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the desired status of the root guard. This variable configures the root guard feature to enforce the root bridge placement in the network." ::= { staPortEntry 18 } staPortBpduGuardAutoRecovery OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "A value of enabled(1) indicates that BPDU port guard auto recovery mechanism is enabled for this port. A value of disabled(2) indicates that the mechanism is disabled." ::= { staPortEntry 19 } staPortBpduGuardAutoRecoveryInterval OBJECT-TYPE SYNTAX Unsigned32(30..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval in seconds used by BPDU guard auto recovery mechanism." ::= { staPortEntry 20 } staPortTcPropStop OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Stop topology change progate on this ifindex. Don't enable on potentially ring port. " ::= { staPortEntry 21 } staProtocolType OBJECT-TYPE SYNTAX INTEGER { stp(1), rstp(2), mstp(3), vstp(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'rstp(2)' indicates that the Rapid Spanning Tree Protocol is as specified in IEEE 802.1w, and the value 'mstp(3)' indicates that the Multiple Spanning Tree Protocol is as specified in IEEE 802.1s. New values may be defined in the future as new or updated versions of the protocol become available." REFERENCE "IEEE 802.1w clause 14.8.1, 17.12, 17.16.1" ::= { staMgt 3 } staTxHoldCount OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value used by the Port Transmit state machine to limit the maximum transmission rate." REFERENCE "IEEE 802.1w clause 17.16.6" DEFVAL { 3 } ::= { staMgt 4 } staPathCostMethod OBJECT-TYPE SYNTAX StaPathCostMode MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the spanning tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the staPortLongPathCost MIB object must be used to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of staPortLongPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used." DEFVAL { short } ::= { staMgt 5} -- for 1s(MSTP/VSTP) start -- -- xstMgt -- xstMgt OBJECT IDENTIFIER ::= { staMgt 6} mstName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the Multiple Spanning Tree region." ::= { xstMgt 1 } mstRevision OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The Revision number of the Multiple Spanning Tree region." ::= { xstMgt 2 } mstMaxHops OBJECT-TYPE SYNTAX Integer32(1..40) MAX-ACCESS read-write STATUS current DESCRIPTION "The max hop number counts of the Multiple Spanning Tree region." ::= { xstMgt 3 } xstInstanceCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF XstInstanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure the property of a specific instance in Multiple Spanning Tree or Rapid Spanning Tree. If Rapid Spanning Tree protocol is in use, the mstInstanceEditIndex is always 0." ::= { xstMgt 4 } xstInstanceCfgEntry OBJECT-TYPE SYNTAX XstInstanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the property of the RST or MST instance." INDEX { xstInstanceCfgIndex } ::= { xstInstanceCfgTable 1 } XstInstanceCfgEntry ::= SEQUENCE { xstInstanceCfgIndex Integer32, xstInstanceCfgPriority Integer32, xstInstanceCfgTimeSinceTopologyChange TimeTicks, xstInstanceCfgTopChanges Integer32, xstInstanceCfgDesignatedRoot BridgeId, xstInstanceCfgRootCost Integer32, xstInstanceCfgRootPort Integer32, xstInstanceCfgMaxAge Timeout, xstInstanceCfgHelloTime Timeout, xstInstanceCfgHoldTime Timeout, xstInstanceCfgForwardDelay Timeout, xstInstanceCfgBridgeMaxAge Timeout, xstInstanceCfgBridgeHelloTime Timeout, xstInstanceCfgBridgeForwardDelay Timeout, xstInstanceCfgTxHoldCount Integer32, xstInstanceCfgPathCostMethod StaPathCostMode } xstInstanceCfgIndex OBJECT-TYPE SYNTAX Integer32 (0..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance." ::= {xstInstanceCfgEntry 1 } xstInstanceCfgPriority OBJECT-TYPE SYNTAX Integer32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096." ::= { xstInstanceCfgEntry 2 } xstInstanceCfgTimeSinceTopologyChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST." ::= { xstInstanceCfgEntry 3 } xstInstanceCfgTopChanges OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized." ::= { xstInstanceCfgEntry 4 } xstInstanceCfgDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identifier parameter in all configuration bridge PDUs originated by this node." REFERENCE "IEEE 802.1w." ::= { xstInstanceCfgEntry 5 } xstInstanceCfgRootCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the root as seen from this bridge of the RST or MST." ::= { xstInstanceCfgEntry 6 } xstInstanceCfgRootPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST." ::= { xstInstanceCfgEntry 7 } xstInstanceCfgMaxAge OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using." ::= { xstInstanceCfgEntry 8 } xstInstanceCfgHelloTime OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using in RST or MST." ::= { xstInstanceCfgEntry 9 } xstInstanceCfgHoldTime OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second." ::= { xstInstanceCfgEntry 10 } xstInstanceCfgForwardDelay OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the port stays in each of the listening and learning states, which precede the forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the forwarding database. This value is the current value being used by the bridge. xstInstanceCfgBridgeForwardDelay defines the value that this bridge and all others would start using if/when this bridge were to become the root." ::= { xstInstanceCfgEntry 11 } xstInstanceCfgBridgeMaxAge OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second." REFERENCE "802.1D-1990." ::= { xstInstanceCfgEntry 12 } xstInstanceCfgBridgeHelloTime OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second." REFERENCE "802.1D-1990." ::= { xstInstanceCfgEntry 13 } xstInstanceCfgBridgeForwardDelay OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second." REFERENCE "802.1D-1990." ::= { xstInstanceCfgEntry 14 } xstInstanceCfgTxHoldCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate." ::= { xstInstanceCfgEntry 15 } xstInstanceCfgPathCostMethod OBJECT-TYPE SYNTAX StaPathCostMode MAX-ACCESS read-only STATUS current DESCRIPTION "For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the xstInstancePortPathCost MIB object must be used in order to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of xstInstancePortPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used." ::= { xstInstanceCfgEntry 16 } xstInstancePortTable OBJECT-TYPE SYNTAX SEQUENCE OF XstInstancePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration." ::= { xstMgt 5 } xstInstancePortEntry OBJECT-TYPE SYNTAX XstInstancePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for xstInstancePortTable." INDEX { xstInstanceCfgIndex, dot1dStpPort } ::= { xstInstancePortTable 1 } XstInstancePortEntry ::= SEQUENCE { xstInstancePortPriority Integer32, xstInstancePortState INTEGER, xstInstancePortEnable EnabledStatus, xstInstancePortDesignatedRoot BridgeId, xstInstancePortDesignatedCost Integer32, xstInstancePortDesignatedBridge BridgeId, xstInstancePortDesignatedPort OCTET STRING, xstInstancePortForwardTransitions Counter32, xstInstancePortPortRole INTEGER, xstInstancePortAdminPathCost Integer32, xstInstancePortOperPathCost Integer32 } xstInstancePortPriority OBJECT-TYPE SYNTAX Integer32(0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active link in the Spanning Tree. This makes a port with higher priority less likely to be blocked if the Spanning Tree Algorithm is detecting network loops. Where more than one port is assigned the highest priority, the port with lowest numeric identifier will be enabled." ::= { xstInstancePortEntry 3 } xstInstancePortState OBJECT-TYPE SYNTAX INTEGER { discarding(1), learning(2), forwarding(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, but does not forward packets. learning(2): Port has transmitted configuration messages for an interval set by the Forward Delay parameter without receiving contradictory information. Port address table is cleared, and the port begins learning addresses. forwarding(3): Port forwards packets, and continues learning addresses. For ports which are disabled (see xstInstancePortEnable), this object will have a value of discarding(1)." ::= { xstInstancePortEntry 4} xstInstancePortEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The enabled/disabled status of the port." ::= { xstInstancePortEntry 5 } xstInstancePortDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached." ::= { xstInstancePortEntry 7 } xstInstancePortDesignatedCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs." ::= { xstInstancePortEntry 8 } xstInstancePortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment." ::= { xstInstancePortEntry 9 } xstInstancePortDesignatedPort OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier of the port on the designated bridge for this port's segment." ::= { xstInstancePortEntry 10 } xstInstancePortForwardTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this port has transitioned from the learning state to the forwarding state." ::= { xstInstancePortEntry 11 } xstInstancePortPortRole OBJECT-TYPE SYNTAX INTEGER { disabled(1), root(2), designated(3), alternate(4), backup(5), master(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port is connecting a LAN through the bridge to the root bridge (i.e., designated port) (4) The port may provide connectivity if other bridges, bridge ports, or LANs fail or are removed. (5) The port provides backup if other bridges, bridge ports, or LANs fail or are removed. (6) For MST protocol only, indicates whether this instance is in a master role." ::= { xstInstancePortEntry 12 } xstInstancePortAdminPathCost OBJECT-TYPE SYNTAX Integer32(1..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The admin value of the MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority)." ::= { xstInstancePortEntry 13 } xstInstancePortOperPathCost OBJECT-TYPE SYNTAX Integer32(1..200000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority)." ::= { xstInstancePortEntry 14 } mstInstanceEditTable OBJECT-TYPE SYNTAX SEQUENCE OF MstInstanceEditEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Multiple Spanning Tree region instance vlan configuration table. Please read the actual instance vlan mapped in the mstInstanceOperTable." ::= { xstMgt 6 } mstInstanceEditEntry OBJECT-TYPE SYNTAX MstInstanceEditEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the status of the MSTP instance." INDEX { mstInstanceEditIndex } ::= { mstInstanceEditTable 1 } MstInstanceEditEntry ::= SEQUENCE { mstInstanceEditIndex Integer32, mstInstanceEditVlansMap OCTET STRING, mstInstanceEditVlansMap2k OCTET STRING, mstInstanceEditVlansMap3k OCTET STRING, mstInstanceEditVlansMap4k OCTET STRING, mstInstanceEditRemainingHops Integer32 } mstInstanceEditIndex OBJECT-TYPE SYNTAX Integer32 (0..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance." ::= {mstInstanceEditEntry 1 } mstInstanceEditVlansMap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list." ::= {mstInstanceEditEntry 2 } mstInstanceEditVlansMap2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list." ::= {mstInstanceEditEntry 3 } mstInstanceEditVlansMap3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list." ::= {mstInstanceEditEntry 4 } mstInstanceEditVlansMap4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list." ::= {mstInstanceEditEntry 5 } mstInstanceEditRemainingHops OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remaining hop count for this MST instance." ::= { mstInstanceEditEntry 6 } --mstInstanceOperTable mstInstanceOperTable OBJECT-TYPE SYNTAX SEQUENCE OF MstInstanceOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Multiple Spanning Tree region instance vlan mapped table." ::= { xstMgt 7 } mstInstanceOperEntry OBJECT-TYPE SYNTAX MstInstanceOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the status of the MSTP instance." INDEX { mstInstanceOperIndex } ::= { mstInstanceOperTable 1 } MstInstanceOperEntry ::= SEQUENCE { mstInstanceOperIndex Integer32, mstInstanceOperVlansMap OCTET STRING, mstInstanceOperVlansMap2k OCTET STRING, mstInstanceOperVlansMap3k OCTET STRING, mstInstanceOperVlansMap4k OCTET STRING } mstInstanceOperIndex OBJECT-TYPE SYNTAX Integer32 (0..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance." ::= {mstInstanceOperEntry 1 } mstInstanceOperVlansMap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'." ::= {mstInstanceOperEntry 2 } mstInstanceOperVlansMap2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'." ::= {mstInstanceOperEntry 3 } mstInstanceOperVlansMap3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'." ::= {mstInstanceOperEntry 4 } mstInstanceOperVlansMap4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'." ::= {mstInstanceOperEntry 5 } vstCfgVlanList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "The configured VLAN list for VSTP. Each VLAN in the list is mapped to one independent instance on VSTP mode. The first octet corresponds to VLANs with VIDs of 1 through 8; the second octet to VLANs 9 through 16; etc., The most significant bit of each octet corresponds to the lowest value VID in that octet. The total number of VLAN set to '1' shall not be more than maximum number of instances supported minus 1." ::= { xstMgt 8 } -- for 1s(MSTP/VSTP) end staLoopbackDetectionPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StaLoopbackDetectionPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to configure the spanning tree loopback detection of each port or trunk" ::= { staMgt 8 } staLoopbackDetectionPortEntry OBJECT-TYPE SYNTAX StaLoopbackDetectionPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of staLoopbackDetectionPortTable." INDEX { staLoopbackDetectionPortIfIndex} ::= { staLoopbackDetectionPortTable 1 } StaLoopbackDetectionPortEntry ::= SEQUENCE { staLoopbackDetectionPortIfIndex InterfaceIndex, staLoopbackDetectionPortStatus EnabledStatus, staLoopbackDetectionPortTrapStatus EnabledStatus, staLoopbackDetectionPortReleaseMode INTEGER, staLoopbackDetectionPortRelease INTEGER } staLoopbackDetectionPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { staLoopbackDetectionPortEntry 1 } staLoopbackDetectionPortStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Status of the port on whether spanning tree loopback detection is enabled." ::= { staLoopbackDetectionPortEntry 2 } staLoopbackDetectionPortTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the loopback BPDUs have been detected." ::= { staLoopbackDetectionPortEntry 3 } staLoopbackDetectionPortReleaseMode OBJECT-TYPE SYNTAX INTEGER { auto(1), manual(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state manually after loopback has occurred." ::= { staLoopbackDetectionPortEntry 4 } staLoopbackDetectionPortRelease OBJECT-TYPE SYNTAX INTEGER { noRelease(1), release(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable." ::= { staLoopbackDetectionPortEntry 5 } staSystemBPDUFlooding OBJECT-TYPE SYNTAX INTEGER { to-vlan(1), to-all(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Global BPDU flooding behavior configuration. When BPDU is received on spanning tree disabled port. (1) BPDU is flooded to all other spanning tree disabled ports in vlan that received BPDU. (2) BPDU is flooded to all other spanning tree disabled ports." DEFVAL { to-vlan } ::= { staMgt 9 } staTcPropGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF StaTcPropGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table describing the configuration of each TC propagation group." ::= { staMgt 10 } staTcPropGroupEntry OBJECT-TYPE SYNTAX StaTcPropGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing the configuration of a particular TC propagation group." INDEX { staTcPropGroupIndex } ::= { staTcPropGroupTable 1 } StaTcPropGroupEntry ::= SEQUENCE { staTcPropGroupIndex Integer32, staTcPropGroupPorts PortList } staTcPropGroupIndex OBJECT-TYPE SYNTAX Integer32(1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies the TC propagation group within the switch that is described by the table entry." ::= { staTcPropGroupEntry 1 } staTcPropGroupPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The complete set of ports currently associated with this TC propagation group. A port can only belong to one group. If a port detects a topology change, this port only notify other ports in the same group to propagate this topology change, and only need to clear MAC address learned on these ports." ::= { staTcPropGroupEntry 2 } -- -- restartMgt -- -- Management for restarting the switch. restartOpCodeFile OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name of op-code file for start-up." ::= { restartMgt 1 } restartConfigFile OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name of configuration file for start-up." ::= { restartMgt 2 } restartControl OBJECT-TYPE SYNTAX INTEGER { running(1), warmBoot(2), coldBoot(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to warmBoot(2) causes the device to reinitialize itself such that neither the agent configuration nor the protocol entity implementation is altered. Setting this object to coldBoot(3) causes the device to reinitialize itself such that the agent's configuration or the protocol entity implementation may be altered. When the device is running normally, this variable has a value of running(1)." ::= { restartMgt 3 } -- -- mirrorMgt -- -- Management for port mirroring. mirrorTable OBJECT-TYPE SYNTAX SEQUENCE OF MirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port mirroring, enabling a port to be mirrored to/from another port. Not all ports can be mirrored and limitations may apply as to which ports can be used as either source or destination ports." ::= { mirrorMgt 1 } mirrorEntry OBJECT-TYPE SYNTAX MirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of mirrorTable." INDEX { mirrorDestinationPort, mirrorSourcePort } ::= { mirrorTable 1 } MirrorEntry ::= SEQUENCE { mirrorDestinationPort InterfaceIndex, mirrorSourcePort InterfaceIndex, mirrorType INTEGER, mirrorStatus ValidStatus } mirrorDestinationPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mirrorEntry 1 } mirrorSourcePort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mirrorEntry 2 } mirrorType OBJECT-TYPE SYNTAX INTEGER { rx(1), tx(2), both(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored." ::= { mirrorEntry 3 } mirrorStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { mirrorEntry 4 } vlanMirrorTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanMirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for VLAN mirroring, enabling a VLAN to be mirrored to a port." ::= { mirrorMgt 2 } vlanMirrorEntry OBJECT-TYPE SYNTAX VlanMirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of vlanMirrorTable." INDEX { vlanMirrorDestinationPort, vlanMirrorSourceVlan } ::= { vlanMirrorTable 1 } VlanMirrorEntry ::= SEQUENCE { vlanMirrorDestinationPort InterfaceIndex, vlanMirrorSourceVlan VlanId, vlanMirrorStatus ValidStatus } vlanMirrorDestinationPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { vlanMirrorEntry 1 } vlanMirrorSourceVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source VLAN for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB." ::= { vlanMirrorEntry 2 } vlanMirrorStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry." ::= { vlanMirrorEntry 4 } -- -- rspanMgt -- rspanTable OBJECT-TYPE SYNTAX SEQUENCE OF RspanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the settings of RSPAN." ::= { mirrorMgt 3 } rspanEntry OBJECT-TYPE SYNTAX RspanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of rspanTable." INDEX { rspanSessionId } ::= { rspanTable 1 } RspanEntry ::= SEQUENCE { rspanSessionId Integer32, rspanSrcTxPorts PortList, rspanSrcRxPorts PortList, rspanDstPort Integer32, rspanDstPortTag INTEGER, rspanSwitchRole INTEGER, rspanRemotePorts PortList, rspanRemoteVlanId Integer32, rspanOperStatus INTEGER, rspanStatus ValidStatus } rspanSessionId OBJECT-TYPE SYNTAX Integer32 (1..2) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The session ID that may specify an entry in the table which contains destination port(s) information." ::= { rspanEntry 1 } rspanSrcTxPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the source port list in tx mode." ::= { rspanEntry 2 } rspanSrcRxPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the source port list in rx mode." ::= { rspanEntry 3 } rspanDstPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The port number of a destination port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { rspanEntry 4 } rspanDstPortTag OBJECT-TYPE SYNTAX INTEGER { none(1), untagged(2), tagged(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the traffic which is sent out from source port with RSPAN VLAN ID or not." ::= { rspanEntry 5 } rspanSwitchRole OBJECT-TYPE SYNTAX INTEGER { none(1), source(2), intermediate(3), destination(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the role of current switch." ::= { rspanEntry 6 } rspanRemotePorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the uplink port list." ::= { rspanEntry 7 } rspanRemoteVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the ID of a RSPAN VLAN." ::= { rspanEntry 8 } rspanOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of the entry. A status of up(1) means the setting of a session is complete and it has started performing its function. A status of down(2) means no function is performed because of incompleted session setting." ::= { rspanEntry 9 } rspanStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry." ::= { rspanEntry 10 } macMirrorTable OBJECT-TYPE SYNTAX SEQUENCE OF MacMirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for MAC mirroring, enabling a MAC address to be mirrored to a port." ::= { mirrorMgt 4 } macMirrorEntry OBJECT-TYPE SYNTAX MacMirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of mirrorMacTable." INDEX { macMirrorDestinationPort, macMirrorSourceMacAddr } ::= { macMirrorTable 1 } MacMirrorEntry ::= SEQUENCE { macMirrorDestinationPort InterfaceIndex, macMirrorSourceMacAddr MacAddress, macMirrorStatus ValidStatus } macMirrorDestinationPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { macMirrorEntry 1 } macMirrorSourceMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Packets with matching source MAC address will be monitored." ::= { macMirrorEntry 2 } macMirrorStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { macMirrorEntry 3 } -- -- igmpSnoopMgt -- -- Management for Internet Group Management Protocol (IGMP) -- Snooping. igmpSnoopStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. " DEFVAL { enabled } ::= { igmpSnoopMgt 1 } igmpSnoopQuerier OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enables (disables) whether the switch acts as an IGMP querier." DEFVAL { enabled } ::= { igmpSnoopMgt 2 } igmpSnoopRouterPortExpireTime OBJECT-TYPE SYNTAX Integer32 (300..500) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the time (in seconds) the switch waits after the previous querier has stopped querying before the router port (which received query packets from previous querier) expires." DEFVAL { 300 } ::= { igmpSnoopMgt 6 } igmpSnoopVersion OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP version snooped" DEFVAL { 2 } ::= { igmpSnoopMgt 7 } igmpSnoopRouterCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopRouterCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for current router ports." ::= { igmpSnoopMgt 8 } igmpSnoopRouterCurrentEntry OBJECT-TYPE SYNTAX IgmpSnoopRouterCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for current router ports." INDEX { igmpSnoopRouterCurrentVlanIndex } ::= { igmpSnoopRouterCurrentTable 1 } IgmpSnoopRouterCurrentEntry ::= SEQUENCE { igmpSnoopRouterCurrentVlanIndex Unsigned32, igmpSnoopRouterCurrentPorts PortList, igmpSnoopRouterCurrentStatus PortList } igmpSnoopRouterCurrentVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable." ::= { igmpSnoopRouterCurrentEntry 1 } igmpSnoopRouterCurrentPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable." ::= { igmpSnoopRouterCurrentEntry 2 } igmpSnoopRouterCurrentStatus OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are static router ports." ::= { igmpSnoopRouterCurrentEntry 3 } igmpSnoopRouterStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopRouterStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for static router ports." ::= { igmpSnoopMgt 9 } igmpSnoopRouterStaticEntry OBJECT-TYPE SYNTAX IgmpSnoopRouterStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for static router ports." INDEX { igmpSnoopRouterStaticVlanIndex } ::= { igmpSnoopRouterStaticTable 1 } IgmpSnoopRouterStaticEntry ::= SEQUENCE { igmpSnoopRouterStaticVlanIndex Unsigned32, igmpSnoopRouterStaticPorts PortList, igmpSnoopRouterStaticStatus ValidStatus } igmpSnoopRouterStaticVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable." ::= { igmpSnoopRouterStaticEntry 1 } igmpSnoopRouterStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are static router ports." ::= { igmpSnoopRouterStaticEntry 2 } igmpSnoopRouterStaticStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { igmpSnoopRouterStaticEntry 3 } igmpSnoopMulticastCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopMulticastCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for current multicast addresses." ::= { igmpSnoopMgt 10 } igmpSnoopMulticastCurrentEntry OBJECT-TYPE SYNTAX IgmpSnoopMulticastCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for current multicast addresses." INDEX { igmpSnoopMulticastCurrentVlanIndex, igmpSnoopMulticastCurrentIpAddress } ::= { igmpSnoopMulticastCurrentTable 1 } IgmpSnoopMulticastCurrentEntry ::= SEQUENCE { igmpSnoopMulticastCurrentVlanIndex Unsigned32, igmpSnoopMulticastCurrentIpAddress IpAddress, igmpSnoopMulticastCurrentPorts PortList, igmpSnoopMulticastCurrentStatus PortList } igmpSnoopMulticastCurrentVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable." ::= { igmpSnoopMulticastCurrentEntry 1 } igmpSnoopMulticastCurrentIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address of multicast group." ::= { igmpSnoopMulticastCurrentEntry 2 } igmpSnoopMulticastCurrentPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable." ::= { igmpSnoopMulticastCurrentEntry 3 } igmpSnoopMulticastCurrentStatus OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are static members." ::= { igmpSnoopMulticastCurrentEntry 4 } igmpSnoopMulticastStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopMulticastStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for static multicast addresses." ::= { igmpSnoopMgt 11 } igmpSnoopMulticastStaticEntry OBJECT-TYPE SYNTAX IgmpSnoopMulticastStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for static multicast addresses." INDEX { igmpSnoopMulticastStaticVlanIndex, igmpSnoopMulticastStaticIpAddress } ::= { igmpSnoopMulticastStaticTable 1 } IgmpSnoopMulticastStaticEntry ::= SEQUENCE { igmpSnoopMulticastStaticVlanIndex Unsigned32, igmpSnoopMulticastStaticIpAddress IpAddress, igmpSnoopMulticastStaticPorts PortList, igmpSnoopMulticastStaticStatus ValidStatus } igmpSnoopMulticastStaticVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable." ::= { igmpSnoopMulticastStaticEntry 1 } igmpSnoopMulticastStaticIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address of multicast group." ::= { igmpSnoopMulticastStaticEntry 2 } igmpSnoopMulticastStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are members." ::= { igmpSnoopMulticastStaticEntry 3 } igmpSnoopMulticastStaticStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { igmpSnoopMulticastStaticEntry 4 } igmpSnoopCurrentVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopCurrentVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for enabling or disabling IGMP snooping per VLAN." ::= { igmpSnoopMgt 14 } igmpSnoopCurrentVlanEntry OBJECT-TYPE SYNTAX IgmpSnoopCurrentVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for enabling or disabling IGMP snooping." INDEX { igmpSnoopCurrentVlanIndex } ::= { igmpSnoopCurrentVlanTable 1 } IgmpSnoopCurrentVlanEntry ::= SEQUENCE { igmpSnoopCurrentVlanIndex VlanIndex, igmpSnoopCurrentVlanStatus EnabledStatus, igmpSnoopCurrentVlanImmediateLeave EnabledStatus, igmpSnoopCurrentVlanGeneralQuerySuppression EnabledStatus, igmpSnoopCurrentVlanLastMemQueryCount Unsigned32, igmpSnoopCurrentVlanLastMemQueryIntvl Unsigned32, igmpSnoopCurrentVlanProxyAddress IpAddress, igmpSnoopCurrentVlanQueryIntvl Unsigned32, igmpSnoopCurrentVlanQueryRespIntvl Unsigned32, igmpSnoopCurrentVlanProxyReporting INTEGER, igmpSnoopCurrentVlanVersion Unsigned32, igmpSnoopCurrentVlanVersionExclusive EnabledStatus, igmpSnoopCurrentVlanReportSupression INTEGER, igmpSnoopCurrentVlanImmediateLeaveByHostIp EnabledStatus } igmpSnoopCurrentVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface." ::= { igmpSnoopCurrentVlanEntry 1 } igmpSnoopCurrentVlanStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping on this VLAN. When enabled, the device will examine IGMP packets and set up filters for IGMP ports." ::= { igmpSnoopCurrentVlanEntry 2 } igmpSnoopCurrentVlanImmediateLeave OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter to enable or disable the Immediate-Leave feature on this VLAN." ::= { igmpSnoopCurrentVlanEntry 3 } igmpSnoopCurrentVlanGeneralQuerySuppression OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter to enable or disable the general query suppresion on this VLAN." ::= { igmpSnoopCurrentVlanEntry 4 } igmpSnoopCurrentVlanLastMemQueryCount OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Represents the number of queries sent by the switch before it assumes there are no local members." ::= { igmpSnoopCurrentVlanEntry 5 } igmpSnoopCurrentVlanLastMemQueryIntvl OBJECT-TYPE SYNTAX Unsigned32(1..31744) MAX-ACCESS read-write STATUS current DESCRIPTION "The last member query interval is the max response time inserted into group-specific queries sent in response to leave group messages,and is also the the max response time inserted into group-and-source-specific query messages." ::= { igmpSnoopCurrentVlanEntry 6 } igmpSnoopCurrentVlanProxyAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Represents the address of queries sent by the switch." ::= { igmpSnoopCurrentVlanEntry 7 } igmpSnoopCurrentVlanQueryIntvl OBJECT-TYPE SYNTAX Unsigned32(2..31744) MAX-ACCESS read-write STATUS current DESCRIPTION "Represents the query interval of queries sent by the switch." ::= { igmpSnoopCurrentVlanEntry 8 } igmpSnoopCurrentVlanQueryRespIntvl OBJECT-TYPE SYNTAX Unsigned32(10..31740) MAX-ACCESS read-write STATUS current DESCRIPTION "Represents the query response interval of queries sent by the switch." ::= { igmpSnoopCurrentVlanEntry 9 } igmpSnoopCurrentVlanProxyReporting OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), default(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this variable to enabled(1) to enable the feature. Set this variable to disabled(2) to disable the feature. Set this variable to default(3), the status of the feature is decided by the global configuration." ::= { igmpSnoopCurrentVlanEntry 10 } igmpSnoopCurrentVlanVersion OBJECT-TYPE SYNTAX Unsigned32(1..3) MAX-ACCESS read-write STATUS current DESCRIPTION "the version of igmp packets is supported by this vlan." ::= { igmpSnoopCurrentVlanEntry 11 } igmpSnoopCurrentVlanVersionExclusive OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable control of the IGMP Snooping exclusive supported version." ::= { igmpSnoopCurrentVlanEntry 12 } igmpSnoopCurrentVlanReportSupression OBJECT-TYPE SYNTAX INTEGER { default(0), enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this variable to enabled(1) to enable the feature. Set this variable to disabled(2) to disable the feature. Set this variable to default(0), the status of the feature is decided by the global configuration." ::= { igmpSnoopCurrentVlanEntry 13 } igmpSnoopCurrentVlanImmediateLeaveByHostIp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter to enable or disable the Immediate-Leave feature by host ip on this VLAN." ::= { igmpSnoopCurrentVlanEntry 14 } igmpSnoopMulticastGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for current multicast addresses." ::= { igmpSnoopMgt 15 } igmpSnoopMulticastGroupEntry OBJECT-TYPE SYNTAX IgmpSnoopMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for Group multicast addresses." INDEX { igmpSnoopMulticastGroupVlanIndex, igmpSnoopMulticastGroupIpAddress, igmpSnoopMulticastGroupSourceIPAddress } ::= { igmpSnoopMulticastGroupTable 1 } IgmpSnoopMulticastGroupEntry ::= SEQUENCE { igmpSnoopMulticastGroupVlanIndex VlanIndex, igmpSnoopMulticastGroupIpAddress IpAddress, igmpSnoopMulticastGroupSourceIPAddress IpAddress, igmpSnoopMulticastGroupPorts PortList, igmpSnoopMulticastGroupStatus PortList } igmpSnoopMulticastGroupVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable." ::= { igmpSnoopMulticastGroupEntry 1 } igmpSnoopMulticastGroupIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address of multicast group." ::= { igmpSnoopMulticastGroupEntry 2 } igmpSnoopMulticastGroupSourceIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Source IP address of source." ::= { igmpSnoopMulticastGroupEntry 3 } igmpSnoopMulticastGroupPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable." ::= { igmpSnoopMulticastGroupEntry 4 } igmpSnoopMulticastGroupStatus OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are static IGMP member ports." ::= { igmpSnoopMulticastGroupEntry 5 } igmpSnoopFilterStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP filtering on the device." ::= { igmpSnoopMgt 17 } igmpSnoopProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the IGMP snooping profile." ::= { igmpSnoopMgt 18 } igmpSnoopProfileEntry OBJECT-TYPE SYNTAX IgmpSnoopProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the IGMP snooping profile." INDEX { igmpSnoopProfileId } ::= { igmpSnoopProfileTable 1 } IgmpSnoopProfileEntry ::= SEQUENCE { igmpSnoopProfileId Unsigned32, igmpSnoopProfileAction INTEGER, igmpSnoopProfileStatus ValidStatus } igmpSnoopProfileId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ID of the IGMP snooping profile." ::= { igmpSnoopProfileEntry 1 } igmpSnoopProfileAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The access mode of the IGMP snooping profile." DEFVAL { deny } ::= { igmpSnoopProfileEntry 2 } igmpSnoopProfileStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { igmpSnoopProfileEntry 3 } igmpSnoopProfileCtl OBJECT IDENTIFIER ::= { igmpSnoopMgt 19 } igmpSnoopProfileCtlId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The ID of the IGMP snooping profile. The default value is zero, meaning that no ID is specified. In order to create a profile, a non-zero value must be specified." ::= { igmpSnoopProfileCtl 1 } igmpSnoopProfileCtlInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The address type is associated with this agent. Only ipv4(1) type is supported." ::= { igmpSnoopProfileCtl 2 } igmpSnoopProfileCtlStartInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The specified addresses in the start of the controlled IP multicast addresses." ::= { igmpSnoopProfileCtl 3 } igmpSnoopProfileCtlEndInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The specified addresses in the end of the controlled IP multicast addresses." ::= { igmpSnoopProfileCtl 4 } igmpSnoopProfileCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), create(2), destroy(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting it to create(2) creates the range of the controlled IP multicast addresses. Setting it to destroy(3) destroys the range of the controlled IP multicast addresses. When the action is completed, this object becomes noAction(1)." ::= { igmpSnoopProfileCtl 5 } igmpSnoopProfileRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopProfileRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the range of the IGMP snooping profile." ::= { igmpSnoopMgt 20 } igmpSnoopProfileRangeEntry OBJECT-TYPE SYNTAX IgmpSnoopProfileRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the range of the IGMP snooping profile." INDEX { igmpSnoopProfileRangeProfileId, igmpSnoopProfileRangeInetAddressType, igmpSnoopProfileRangeStartInetAddress } ::= { igmpSnoopProfileRangeTable 1 } IgmpSnoopProfileRangeEntry ::= SEQUENCE { igmpSnoopProfileRangeProfileId Unsigned32, igmpSnoopProfileRangeInetAddressType InetAddressType, igmpSnoopProfileRangeStartInetAddress InetAddress, igmpSnoopProfileRangeEndInetAddress InetAddress, igmpSnoopProfileRangeAction INTEGER } igmpSnoopProfileRangeProfileId OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as igmpSnoopProfileId." ::= { igmpSnoopProfileRangeEntry 1 } igmpSnoopProfileRangeInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type is associated with this agent. Only ipv4(1) type is supported." ::= { igmpSnoopProfileRangeEntry 2 } igmpSnoopProfileRangeStartInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The specified addresses in the start of the controlled IP multicast addresses." ::= { igmpSnoopProfileRangeEntry 3 } igmpSnoopProfileRangeEndInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The specified addresses in the end of the controlled IP multicast addresses." ::= { igmpSnoopProfileRangeEntry 4 } igmpSnoopProfileRangeAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The access mode of the IGMP snooping profile." DEFVAL { deny } ::= { igmpSnoopProfileRangeEntry 5 } igmpSnoopFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in IGMP filtering." ::= { igmpSnoopMgt 21 } igmpSnoopFilterPortEntry OBJECT-TYPE SYNTAX IgmpSnoopFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in IGMP filtering." INDEX { igmpSnoopFilterPortIndex } ::= { igmpSnoopFilterPortTable 1 } IgmpSnoopFilterPortEntry ::= SEQUENCE { igmpSnoopFilterPortIndex Unsigned32, igmpSnoopFilterPortProfileId Integer32 } igmpSnoopFilterPortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { igmpSnoopFilterPortEntry 1 } igmpSnoopFilterPortProfileId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTable, then no association exists. In particular, if this value is zero, no associated profile will be generated, as zero is not a valid profile index." ::= { igmpSnoopFilterPortEntry 2 } igmpSnoopThrottlePortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopThrottlePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in IGMP throttling." ::= { igmpSnoopMgt 22 } igmpSnoopThrottlePortEntry OBJECT-TYPE SYNTAX IgmpSnoopThrottlePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in IGMP throttling." INDEX { igmpSnoopThrottlePortIndex } ::= { igmpSnoopThrottlePortTable 1 } IgmpSnoopThrottlePortEntry ::= SEQUENCE { igmpSnoopThrottlePortIndex Unsigned32, igmpSnoopThrottlePortRunningStatus INTEGER, igmpSnoopThrottlePortAction INTEGER, igmpSnoopThrottlePortMaxGroups Integer32, igmpSnoopThrottlePortCurrentGroups Integer32 } igmpSnoopThrottlePortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { igmpSnoopThrottlePortEntry 1 } igmpSnoopThrottlePortRunningStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive." ::= { igmpSnoopThrottlePortEntry 2 } igmpSnoopThrottlePortAction OBJECT-TYPE SYNTAX INTEGER { replace(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join. A value of deny(2) means to deny the IGMP report request when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join." DEFVAL { deny } ::= { igmpSnoopThrottlePortEntry 3 } igmpSnoopThrottlePortMaxGroups OBJECT-TYPE SYNTAX Integer32(0..256) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of IGMP groups that the interface can join." ::= { igmpSnoopThrottlePortEntry 4 } igmpSnoopThrottlePortCurrentGroups OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of IGMP groups that the interface has joined." ::= { igmpSnoopThrottlePortEntry 5} -- -- -- igmpSnoopPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of IGMP Snooping service per port." ::= {igmpSnoopMgt 27 } igmpSnoopPortEntry OBJECT-TYPE SYNTAX IgmpSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of IGMP Snooping service per port." INDEX { igmpSnoopPortIndex } ::= {igmpSnoopPortTable 1} IgmpSnoopPortEntry ::= SEQUENCE { igmpSnoopPortIndex Unsigned32, igmpSnoopQueryDrop INTEGER, igmpSnoopMulticastDataDrop INTEGER, igmpSnoopPortNumGroups Unsigned32, igmpSnoopPortNumJoinSend Unsigned32, igmpSnoopPortNumJoins Unsigned32, igmpSnoopPortNumJoinSuccess Unsigned32, igmpSnoopPortNumLeavesSend Unsigned32, igmpSnoopPortNumLeaves Unsigned32, igmpSnoopPortNumGeneralQuerySend Unsigned32, igmpSnoopPortNumGeneralQueryRecevied Unsigned32, igmpSnoopPortNumSepcificQuerySend Unsigned32, igmpSnoopPortNumSpecificQueryReceived Unsigned32, igmpSnoopPortNumInvalidReport Unsigned32, igmpSnoopPortClearStatistics TruthValue, igmpSnoopAuthentication INTEGER } igmpSnoopPortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the igmpSnoopPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { igmpSnoopPortEntry 1 } igmpSnoopQueryDrop OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable dropping IGMP Query packet." DEFVAL { disable } ::= { igmpSnoopPortEntry 3 } igmpSnoopMulticastDataDrop OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable dropping IP multicast data " DEFVAL { disable } ::= { igmpSnoopPortEntry 4 } igmpSnoopPortNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { igmpSnoopPortEntry 5 } igmpSnoopPortNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send " ::= { igmpSnoopPortEntry 6 } igmpSnoopPortNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join recieved " ::= { igmpSnoopPortEntry 7 } igmpSnoopPortNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join group success " ::= { igmpSnoopPortEntry 8 } igmpSnoopPortNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send" ::= { igmpSnoopPortEntry 9 } igmpSnoopPortNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { igmpSnoopPortEntry 10} igmpSnoopPortNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send. " ::= { igmpSnoopPortEntry 11} igmpSnoopPortNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received. " ::= { igmpSnoopPortEntry 12} igmpSnoopPortNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send. " ::= { igmpSnoopPortEntry 13} igmpSnoopPortNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query received. " ::= { igmpSnoopPortEntry 14} igmpSnoopPortNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received. " ::= { igmpSnoopPortEntry 15} igmpSnoopPortClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN all statistics " ::= { igmpSnoopPortEntry 16} igmpSnoopAuthentication OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP Authentication " DEFVAL { disable } ::= { igmpSnoopPortEntry 17 } igmpSnoopGlobalMgt OBJECT IDENTIFIER ::= { igmpSnoopMgt 28 } -- -- igmpSnoopGlobalMgt -- -- Global Management for Internet Group Management Protocol (IGMP) -- Snooping. igmpSnoopProxyReporting OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping proxy reporting on the device." DEFVAL { disabled } ::= { igmpSnoopGlobalMgt 1 } igmpSnoopRouterAlertOptionCheck OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping router alert option check on the device." DEFVAL { disabled } ::= { igmpSnoopGlobalMgt 2 } igmpSnoopTcnFlood OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping tcn flood on the device." DEFVAL { disabled } ::= { igmpSnoopGlobalMgt 3 } igmpSnoopTcnQuerySolicit OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping tcn query solicit on the device." DEFVAL { disabled } ::= { igmpSnoopGlobalMgt 4 } igmpSnoopUnregisteredDataFlood OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping Unregistered data flood solicit on the device." DEFVAL { disabled } ::= { igmpSnoopGlobalMgt 5 } igmpSnoopUnsolicitedReportInterval OBJECT-TYPE SYNTAX Unsigned32(1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to specify how long (in seconds) the uplink ports should transmit unsolicited reports." DEFVAL { 400 } ::= { igmpSnoopGlobalMgt 6 } igmpSnoopVersionExclusive OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping version exclusive on the device." DEFVAL { disabled } ::= { igmpSnoopGlobalMgt 7 } igmpSnoopMrouterForwardMode OBJECT-TYPE SYNTAX INTEGER { dynamic(1), forward(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Paremete to set IGMP snooping Mrouter port forward mode. When set dynamic, IGMP snooping Mrouter port won't forward multicast streams received from other mrouter port. When set forward, IGMP snooping Mrouter port will forward multicast streams received from other mrouter port. " ::= { igmpSnoopGlobalMgt 8 } igmpSnoopForwardingPriority OBJECT-TYPE SYNTAX Integer32(0..7|65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure IGMP snooping multicast stream forwarding priority. If value is 65535, it means the priority is disabled" ::= { igmpSnoopMgt 29 } igmpSnoopQueryDropTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopQueryDropEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of IGMP Snooping query drop per vlan and per vlan configuration." ::= {igmpSnoopMgt 30 } igmpSnoopQueryDropEntry OBJECT-TYPE SYNTAX IgmpSnoopQueryDropEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of IGMP Snooping service per port and per VLAN." INDEX { igmpSnoopQueryDropPortIndex } ::= {igmpSnoopQueryDropTable 1} IgmpSnoopQueryDropEntry ::= SEQUENCE { igmpSnoopQueryDropPortIndex Unsigned32, igmpSnoopQueryDropVlanBitmap OCTET STRING } igmpSnoopQueryDropPortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the igmpSnoopPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { igmpSnoopQueryDropEntry 1 } igmpSnoopQueryDropVlanBitmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(512)) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN bitmap which query drop applied on this port. If all zero, it means disable, For all VLAN, please use igmpSnoopPortTable to configure." ::= { igmpSnoopQueryDropEntry 2 } igmpSnoopClearDynamicGroups OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The current number of IGMP groups that the interface has joined." ::= { igmpSnoopMgt 32} igmpSnoopVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of IGMP Snooping service per port." ::= {igmpSnoopMgt 33 } igmpSnoopVlanEntry OBJECT-TYPE SYNTAX IgmpSnoopVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of IGMP Snooping service per VLAN." INDEX { igmpSnoopVlanIndex } ::= {igmpSnoopVlanTable 1} IgmpSnoopVlanEntry ::= SEQUENCE { igmpSnoopVlanIndex VlanIndex, igmpSnoopVlanNumGroups Unsigned32, igmpSnoopVlanNumJoinSend Unsigned32, igmpSnoopVlanNumJoins Unsigned32, igmpSnoopVlanNumJoinSuccess Unsigned32, igmpSnoopVlanNumLeavesSend Unsigned32, igmpSnoopVlanNumLeaves Unsigned32, igmpSnoopVlanNumGeneralQuerySend Unsigned32, igmpSnoopVlanNumGeneralQueryRecevied Unsigned32, igmpSnoopVlanNumSepcificQuerySend Unsigned32, igmpSnoopVlanNumSpecificQueryReceived Unsigned32, igmpSnoopVlanNumInvalidReport Unsigned32, igmpSnoopVlanClearStatistics TruthValue } igmpSnoopVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN ID" ::= { igmpSnoopVlanEntry 1 } igmpSnoopVlanNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { igmpSnoopVlanEntry 2 } igmpSnoopVlanNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send." ::= { igmpSnoopVlanEntry 3 } igmpSnoopVlanNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join received " ::= { igmpSnoopVlanEntry 4 } igmpSnoopVlanNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of jion success " ::= { igmpSnoopVlanEntry 5 } igmpSnoopVlanNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send." ::= { igmpSnoopVlanEntry 6 } igmpSnoopVlanNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { igmpSnoopVlanEntry 7} igmpSnoopVlanNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send " ::= { igmpSnoopVlanEntry 8} igmpSnoopVlanNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received " ::= { igmpSnoopVlanEntry 9} igmpSnoopVlanNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send" ::= { igmpSnoopVlanEntry 10} igmpSnoopVlanNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sepcific query received " ::= { igmpSnoopVlanEntry 11} igmpSnoopVlanNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received" ::= { igmpSnoopVlanEntry 12} igmpSnoopVlanClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN statistics" ::= { igmpSnoopVlanEntry 13} -- -- The IpMgt Group -- -- Management for Internet Protocol (IP). netDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0." ::= { ipMgt 2 } ipHttpState OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether HTTP is enabled." ::= { ipMgt 3 } ipHttpPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The port number for HTTP." ::= { ipMgt 4 } ipDhcpRestart OBJECT-TYPE SYNTAX INTEGER { restart(1), noRestart(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to restart(1) the DHCP server will restart. When read, this value always returns noRestart(2)." ::= { ipMgt 5 } -- optional ipHttpsState OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether HTTPS is enabled." ::= { ipMgt 6 } ipHttpsPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The port number for HTTPS." ::= { ipMgt 7 } iPAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IPAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of iPAddrEntry." ::= { ipMgt 16 } iPAddrEntry OBJECT-TYPE SYNTAX IPAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface." INDEX { iPAddrIfIndex, iPAddrIPAddress, iPAddrSubnetMask } ::= { iPAddrTable 1 } IPAddrEntry ::= SEQUENCE { iPAddrIfIndex Integer32, iPAddrIPAddress IpAddress, iPAddrSubnetMask IpAddress, iPAddrPrimaryInterface INTEGER, iPAddrUnnumbered INTEGER, iPAddrStatus RowStatus } iPAddrIfIndex OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table." ::= { iPAddrEntry 1 } iPAddrIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask is 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device)." ::= { iPAddrEntry 2 } iPAddrSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device)." ::= { iPAddrEntry 3 } iPAddrPrimaryInterface OBJECT-TYPE SYNTAX INTEGER { unknownType(0), primary(1), secondary(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Whether this is a primary interface." ::= { iPAddrEntry 4 } iPAddrUnnumbered OBJECT-TYPE SYNTAX INTEGER { unnumbered(1), notUnnumbered(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether this is an unnumbered interface." ::= { iPAddrEntry 5 } iPAddrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { iPAddrEntry 6 } dhcpMgt OBJECT IDENTIFIER ::= { ipMgt 11 } dhcpClient OBJECT IDENTIFIER ::= { dhcpMgt 1 } dhcpOption82 OBJECT IDENTIFIER ::= { dhcpMgt 4 } dhcpcOptions OBJECT IDENTIFIER ::= { dhcpClient 1 } dhcpcInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpcInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for DHCP client information listed by interface. Depending on the nature of the product, this table may have only one entry(e.g. for the management VLAN), or may have many entries(e.g. for all ports, or for all static VLANs)." ::= { dhcpcOptions 1 } dhcpcInterfaceEntry OBJECT-TYPE SYNTAX DhcpcInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for DHCP client information listed by interface." INDEX { dhcpcIfIndex } ::= { dhcpcInterfaceTable 1 } DhcpcInterfaceEntry ::= SEQUENCE { dhcpcIfIndex Integer32, dhcpcIfVendorClassIdMode INTEGER, dhcpcIfVendorClassId OCTET STRING } dhcpcIfIndex OBJECT-TYPE SYNTAX Integer32(1..4093) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined by ifIndex in the IF-MIB.(static vlan if index)" ::= { dhcpcInterfaceEntry 1 } dhcpcIfVendorClassIdMode OBJECT-TYPE SYNTAX INTEGER { notSpecify(1), text(2), hex(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether the vendor class ID is in text mode or in Hex mode." ::= { dhcpcInterfaceEntry 4 } dhcpcIfVendorClassId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value that the DHCP client sets in the vendor class_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to identify vendor classof the client." ::= { dhcpcInterfaceEntry 5 } dhcpRelay OBJECT IDENTIFIER ::= { dhcpMgt 2 } --dhcpRelayServerAddrTable dhcpRelayServerAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRelayServerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The role of the DHCP relay agent is to forward requests and replies between server and client when they are not in the same subnet. To enable DHCP relay service the user needs to specify relay server IP address and then restart DHCP relay. This table is to specify relay server IP address, the maximum number of server IP addresses user can specify is 5. To restart DHCP relay, please use the dhcpRelayRestart variable." ::= { dhcpRelay 2 } dhcpRelayServerAddrEntry OBJECT-TYPE SYNTAX DhcpRelayServerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpRelayServerAddrTable." INDEX { dhcpRelayServerAddrIfIndex,dhcpRelayServerAddrIndex } ::= { dhcpRelayServerAddrTable 1 } DhcpRelayServerAddrEntry ::= SEQUENCE { dhcpRelayServerAddrIfIndex Integer32, dhcpRelayServerAddrIndex Integer32, dhcpRelayServerAddrServerIp IpAddress } dhcpRelayServerAddrIfIndex OBJECT-TYPE SYNTAX Integer32(1..4093) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN interface being used by this table entry." ::= { dhcpRelayServerAddrEntry 1 } dhcpRelayServerAddrIndex OBJECT-TYPE SYNTAX Integer32 (0..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the relay server IP address." ::= { dhcpRelayServerAddrEntry 2 } dhcpRelayServerAddrServerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the relay server." ::= { dhcpRelayServerAddrEntry 3 } --dhcpRelayRestart dhcpRelayRestart OBJECT-TYPE SYNTAX INTEGER { restart(1), noRestart(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to restart(1) to restart DCHP Relay. Always get noRestart(2) when you read this variable." ::= { dhcpRelay 3 } dhcpRelayServerInetAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRelayServerInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The role of DHCP Relay Agent is to forward requests and replies between server and client when they are not in the same subnet. To enable DHCP Relay service user needs to specify Relay Server IP address and then restart DHCP Relay. This Table is to specify Relay Server IP address, the maximum numbers of server IP addresses user can specify is 5. To Restart DHCP Relay, please use the dhcpRelayRestart variable." ::= { dhcpRelay 4 } dhcpRelayServerInetAddrEntry OBJECT-TYPE SYNTAX DhcpRelayServerInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpRelayServerInetAddrTable." INDEX { dhcpRelayServerInetAddrVlanIndex, dhcpRelayServerInetAddrIndex } ::= { dhcpRelayServerInetAddrTable 1 } DhcpRelayServerInetAddrEntry ::= SEQUENCE { dhcpRelayServerInetAddrVlanIndex VlanIndex, dhcpRelayServerInetAddrIndex Integer32, dhcpRelayServerInetAddrType InetAddressType, dhcpRelayServerInetAddr InetAddress } dhcpRelayServerInetAddrVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN interface being used by this table entry." ::= { dhcpRelayServerInetAddrEntry 1 } dhcpRelayServerInetAddrIndex OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the Relay server IP address." ::= { dhcpRelayServerInetAddrEntry 2 } dhcpRelayServerInetAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The INET address type of the relay server." ::= { dhcpRelayServerInetAddrEntry 3 } dhcpRelayServerInetAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The INET address of the relay server." ::= { dhcpRelayServerInetAddrEntry 4 } -- -- dhcpServerMgt -- dhcpServerMgt OBJECT IDENTIFIER ::= { dhcpMgt 3 } dhcpServerServiceStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to 1 to enable the DHCP server service. Setting this to 2 to disable the DHCP server service." ::= { dhcpServerMgt 8 } --dhcpPoolInetTable dhcpPoolInetTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpPoolInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A DHCP pool is a collection of user configuration such as option config-lease time or DNS-server IPs, a network address for network pool, or a host IP plus a hardware address pair for host pool. However, a DHCP pool only can either be a network pool or a host pool, or none of them (such as that pool only containing option config no network address config or a host IP config as well)." ::= { dhcpServerMgt 9 } dhcpPoolInetEntry OBJECT-TYPE SYNTAX DhcpPoolInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpPoolInetTable. " INDEX { dhcpPoolInetPoolName } ::= { dhcpPoolInetTable 1 } DhcpPoolInetEntry ::= SEQUENCE { dhcpPoolInetPoolName DisplayString, dhcpPoolInetPoolType INTEGER, dhcpPoolInetAddressType InetAddressType, dhcpPoolInetAddress InetAddress, dhcpPoolInetSubnetMaskType InetAddressType, dhcpPoolInetSubnetMask InetAddress, dhcpPoolInetHardwareType INTEGER, dhcpPoolInetMacAddress OCTET STRING, dhcpPoolInetStatus ValidStatus } dhcpPoolInetPoolName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pool name, simply specify a string with its length NO MORE THAN 32." ::= { dhcpPoolInetEntry 1 } dhcpPoolInetPoolType OBJECT-TYPE SYNTAX INTEGER { notSpecified(1), network(2), host(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Pool type: notSpecified(1), network(2), host(3)." ::= { dhcpPoolInetEntry 2 } dhcpPoolInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Pool address type" ::= { dhcpPoolInetEntry 3 } dhcpPoolInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Pool address" ::= { dhcpPoolInetEntry 4 } dhcpPoolInetSubnetMaskType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "subnet mask type" ::= { dhcpPoolInetEntry 5 } dhcpPoolInetSubnetMask OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "subnet mask " ::= { dhcpPoolInetEntry 6 } dhcpPoolInetHardwareType OBJECT-TYPE SYNTAX INTEGER { notSpecified(1), ethernet(2), ieee802(3), fddi(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Hardware type: notSpecified(1), ethernet(2), ieee802(3) ,fddi(4)." ::= { dhcpPoolInetEntry 7 } dhcpPoolInetMacAddress OBJECT-TYPE SYNTAX OCTET STRING(SIZE(6)) MAX-ACCESS read-create STATUS current DESCRIPTION "MAC address. " ::= { dhcpPoolInetEntry 8 } dhcpPoolInetStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { dhcpPoolInetEntry 9 } --dhcpPoolInetOptionTable dhcpPoolInetOptionTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpPoolInetOptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the Option table of the dhcpPoolTable, user can specify options configuration in this table." ::= { dhcpServerMgt 10 } dhcpPoolInetOptionEntry OBJECT-TYPE SYNTAX DhcpPoolInetOptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpPoolOptionTable." INDEX { dhcpPoolInetOptionPoolName } ::= { dhcpPoolInetOptionTable 1 } DhcpPoolInetOptionEntry ::= SEQUENCE { dhcpPoolInetOptionPoolName DisplayString, dhcpPoolInetOptionNextServerAddrType InetAddressType, dhcpPoolInetOptionNextServerAddr InetAddress, dhcpPoolInetOptionNetbiosNodeType INTEGER, dhcpPoolInetOptionDomainName DisplayString, dhcpPoolInetOptionBootFile DisplayString, dhcpPoolInetOptionLeaseTime Integer32, dhcpPoolInetOptionCidMode INTEGER, dhcpPoolInetOptionCidBuffer OCTET STRING } dhcpPoolInetOptionPoolName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pool name, simply specify a string with its length NO MORE THAN 32." ::= { dhcpPoolInetOptionEntry 1 } dhcpPoolInetOptionNextServerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the INET address type of the next server in the boot process." ::= { dhcpPoolInetOptionEntry 2 } dhcpPoolInetOptionNextServerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the INET address of the next server in the boot process, which is typically a Trivial File Transfer Protocol(TFTP) server. One INET address is required." ::= { dhcpPoolInetOptionEntry 3 } dhcpPoolInetOptionNetbiosNodeType OBJECT-TYPE SYNTAX INTEGER { none(1), b-node(2), p-node(3), m-node(4), h-node(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the NetBIOS node type. Valid types are: none(1) b-node(2) - Broadcast p-node(3) - Peer-to-peer m-node(4) - Mixed h-node(5) - Hybrid." ::= { dhcpPoolInetOptionEntry 4 } dhcpPoolInetOptionDomainName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the domain name string." ::= { dhcpPoolInetOptionEntry 5 } dhcpPoolInetOptionBootFile OBJECT-TYPE SYNTAX DisplayString(SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "To specify the name of the default boot image." ::= { dhcpPoolInetOptionEntry 6 } dhcpPoolInetOptionLeaseTime OBJECT-TYPE SYNTAX Integer32(1..31536000|'7FFFFFFF'H) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "To configure the duration of the lease, in seconds, of an IP address that is assigned from a DHCP Server to a DHCP client. Valid values are from 1 to 31536000 (365 days), and a large number '7FFFFFFF'h, which is 'practically infinite'." ::= { dhcpPoolInetOptionEntry 7 } dhcpPoolInetOptionCidMode OBJECT-TYPE SYNTAX INTEGER { notSpecified(1), text(2), hex(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this variable to text(2) or hex(3) to specify the mode of the client ID, which is useful for CLI to determine the display format of the client ID. The original value of object is set to 'notSpecified(1)'. But setting it to notSpecified(1) is a invalid operation." ::= { dhcpPoolInetOptionEntry 8 } dhcpPoolInetOptionCidBuffer OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "Content of Client Id. dhcpPoolOptionCidMode MUST be specified before setting this variable." ::= { dhcpPoolInetOptionEntry 9 } --dhcpPoolInetOptionDnsSerTable dhcpPoolInetOptionDnsSerTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpPoolInetOptionDnsSerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To specify the DNS IP servers available to a DHCP client, you can specify up to two addresses for each DHCP pool." ::= { dhcpServerMgt 11 } dhcpPoolInetOptionDnsSerEntry OBJECT-TYPE SYNTAX DhcpPoolInetOptionDnsSerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpPoolOptionDnsSerTable." INDEX { dhcpPoolInetOptionDnsSerPoolName, dhcpPoolInetOptionDnsSerIndex } ::= { dhcpPoolInetOptionDnsSerTable 1 } DhcpPoolInetOptionDnsSerEntry ::= SEQUENCE { dhcpPoolInetOptionDnsSerPoolName DisplayString, dhcpPoolInetOptionDnsSerIndex Integer32, dhcpPoolInetOptionDnsSerAddrType InetAddressType, dhcpPoolInetOptionDnsSerAddr InetAddress } dhcpPoolInetOptionDnsSerPoolName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pool name, simply specify a string with its length NO MORE THAN 32." ::= { dhcpPoolInetOptionDnsSerEntry 1 } dhcpPoolInetOptionDnsSerIndex OBJECT-TYPE SYNTAX Integer32(1..2) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the DNS server." ::= { dhcpPoolInetOptionDnsSerEntry 2 } dhcpPoolInetOptionDnsSerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "INET address type of the DNS server." ::= { dhcpPoolInetOptionDnsSerEntry 3 } dhcpPoolInetOptionDnsSerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "INET address of the DNS server." ::= { dhcpPoolInetOptionDnsSerEntry 4 } --dhcpPoolOptInetDefaultRouterTable dhcpPoolOptInetDefaultRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpPoolOptInetDefaultRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the default router list for a DHCP Client, you can specify up to two addresses for each DHCP pool." ::= { dhcpServerMgt 12 } dhcpPoolOptInetDefaultRouterEntry OBJECT-TYPE SYNTAX DhcpPoolOptInetDefaultRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpPoolOptDefaultRouterTable." INDEX { dhcpPoolOptInetDefaultRouterPoolName, dhcpPoolOptInetDefaultRouterIndex } ::= { dhcpPoolOptInetDefaultRouterTable 1 } DhcpPoolOptInetDefaultRouterEntry ::= SEQUENCE { dhcpPoolOptInetDefaultRouterPoolName DisplayString, dhcpPoolOptInetDefaultRouterIndex Integer32, dhcpPoolOptInetDefaultRouterAddrType InetAddressType, dhcpPoolOptInetDefaultRouterAddr InetAddress } dhcpPoolOptInetDefaultRouterPoolName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pool name, simply specify a string with its length NO MORE THAN 32." ::= { dhcpPoolOptInetDefaultRouterEntry 1 } dhcpPoolOptInetDefaultRouterIndex OBJECT-TYPE SYNTAX Integer32 (1..2) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the default router." ::= { dhcpPoolOptInetDefaultRouterEntry 2 } dhcpPoolOptInetDefaultRouterAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the INET address type of a router." ::= { dhcpPoolOptInetDefaultRouterEntry 3 } dhcpPoolOptInetDefaultRouterAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the INET address of a router." ::= { dhcpPoolOptInetDefaultRouterEntry 4 } --dhcpPoolOptInetNetbiosServerTable dhcpPoolOptInetNetbiosServerTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpPoolOptInetNetbiosServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To configure the NetBIOS WINS name servers that are available to DHCP clients. You can specify up to eight addressed for each DHCP pool." ::= { dhcpServerMgt 13 } dhcpPoolOptInetNetbiosServerEntry OBJECT-TYPE SYNTAX DhcpPoolOptInetNetbiosServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpPoolOptNetbiosServerTable." INDEX { dhcpPoolOptInetNetbiosServerPoolName, dhcpPoolOptInetNetbiosServerIndex } ::= { dhcpPoolOptInetNetbiosServerTable 1 } DhcpPoolOptInetNetbiosServerEntry ::= SEQUENCE { dhcpPoolOptInetNetbiosServerPoolName DisplayString, dhcpPoolOptInetNetbiosServerIndex Integer32, dhcpPoolOptInetNetbiosServerAddrType InetAddressType, dhcpPoolOptInetNetbiosServerAddr InetAddress } dhcpPoolOptInetNetbiosServerPoolName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pool name, simply specify a string with its length NO MORE THAN 32" ::= { dhcpPoolOptInetNetbiosServerEntry 1 } dhcpPoolOptInetNetbiosServerIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the NetBIOS name Server." ::= { dhcpPoolOptInetNetbiosServerEntry 2 } dhcpPoolOptInetNetbiosServerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the INET address type of the NetBIOS WINS name server." ::= { dhcpPoolOptInetNetbiosServerEntry 3 } dhcpPoolOptInetNetbiosServerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the INET address of the NetBIOS WINS name server." ::= { dhcpPoolOptInetNetbiosServerEntry 4 } --dhcpServerExcludedInetAddrTable dhcpServerExcludedInetAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpServerExcludedInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To specify IP addresses that a DHCP Server should not assign to DHCP clients." ::= { dhcpServerMgt 14 } dhcpServerExcludedInetAddrEntry OBJECT-TYPE SYNTAX DhcpServerExcludedInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpServerExcludedIpAddrTable." INDEX { dhcpServerExcludedInetAddrLowAddrType, dhcpServerExcludedInetAddrLowAddr, dhcpServerExcludedInetAddrHighAddrType, dhcpServerExcludedInetAddrHighAddr } ::= { dhcpServerExcludedInetAddrTable 1 } DhcpServerExcludedInetAddrEntry ::= SEQUENCE { dhcpServerExcludedInetAddrLowAddrType InetAddressType, dhcpServerExcludedInetAddrLowAddr InetAddress, dhcpServerExcludedInetAddrHighAddrType InetAddressType, dhcpServerExcludedInetAddrHighAddr InetAddress, dhcpServerExcludedInetAddrStatus ValidStatus } dhcpServerExcludedInetAddrLowAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The excluded INET address type, or first INET address type in an excluded address range." ::= { dhcpServerExcludedInetAddrEntry 1 } dhcpServerExcludedInetAddrLowAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The excluded INET address, or first INET address in an excluded address range." ::= { dhcpServerExcludedInetAddrEntry 2 } dhcpServerExcludedInetAddrHighAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The last INET address type in the excluded address range." ::= { dhcpServerExcludedInetAddrEntry 3 } dhcpServerExcludedInetAddrHighAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The last INET address in the excluded address range." ::= { dhcpServerExcludedInetAddrEntry 4 } dhcpServerExcludedInetAddrStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { dhcpServerExcludedInetAddrEntry 5 } --dhcpServerInetLeaseBindingTable dhcpServerInetLeaseBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpServerInetLeaseBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To configure the address bindings on the DHCP server." ::= { dhcpServerMgt 15 } dhcpServerInetLeaseBindingEntry OBJECT-TYPE SYNTAX DhcpServerInetLeaseBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpServerLeaseBindingTable." INDEX { dhcpServerInetLeaseBindingAddrType, dhcpServerInetLeaseBindingAddr } ::= { dhcpServerInetLeaseBindingTable 1 } DhcpServerInetLeaseBindingEntry ::= SEQUENCE { dhcpServerInetLeaseBindingAddrType InetAddressType, dhcpServerInetLeaseBindingAddr InetAddress, dhcpServerInetLeaseBindingMac OCTET STRING, dhcpServerInetLeaseBindingLeaseTime Integer32, dhcpServerInetLeaseBindingStartTime DisplayString, dhcpServerInetLeaseBindingStatus ValidStatus } dhcpServerInetLeaseBindingAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The INET address type of the host as recorded on the DHCP server." ::= { dhcpServerInetLeaseBindingEntry 1 } dhcpServerInetLeaseBindingAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The INET address of the host as recorded on the DHCP server." ::= { dhcpServerInetLeaseBindingEntry 2 } dhcpServerInetLeaseBindingMac OBJECT-TYPE SYNTAX OCTET STRING (SIZE(6)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the host as recorded on the DHCP Server." ::= { dhcpServerInetLeaseBindingEntry 3 } dhcpServerInetLeaseBindingLeaseTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The lease expiration date of the INET address of the host." ::= { dhcpServerInetLeaseBindingEntry 4 } dhcpServerInetLeaseBindingStartTime OBJECT-TYPE SYNTAX DisplayString (SIZE(20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Show current system real time in sec." ::= { dhcpServerInetLeaseBindingEntry 5 } dhcpServerInetLeaseBindingStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { dhcpServerInetLeaseBindingEntry 6 } --dhcpPoolOptInetVendorSpecInfoTable dhcpPoolOptInetVendorSpecInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpPoolOptInetVendorSpecInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To configure the option 43 Vendor Specific Information for DHCP clients. You can specify option type for each DHCP pool." ::= { dhcpServerMgt 16 } dhcpPoolOptInetVendorSpecInfoEntry OBJECT-TYPE SYNTAX DhcpPoolOptInetVendorSpecInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpPoolOptInetVendorSpecInfoTable." INDEX { dhcpPoolOptInetVendorSpecInfoPoolName, dhcpPoolOptInetVendorSpecInfoIndex } ::= { dhcpPoolOptInetVendorSpecInfoTable 1 } DhcpPoolOptInetVendorSpecInfoEntry ::= SEQUENCE { dhcpPoolOptInetVendorSpecInfoPoolName DisplayString, dhcpPoolOptInetVendorSpecInfoIndex Integer32, dhcpPoolOptInetVendorSpecInfoMode INTEGER, dhcpPoolOptInetVendorSpecInfoBuffer OCTET STRING, dhcpPoolOptInetVendorSpecInfoAddr InetAddress } dhcpPoolOptInetVendorSpecInfoPoolName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pool name, simply specify a string with its length NO MORE THAN 32" ::= { dhcpPoolOptInetVendorSpecInfoEntry 1 } dhcpPoolOptInetVendorSpecInfoIndex OBJECT-TYPE SYNTAX Integer32(1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the Vendor Specific Information." ::= { dhcpPoolOptInetVendorSpecInfoEntry 2 } dhcpPoolOptInetVendorSpecInfoMode OBJECT-TYPE SYNTAX INTEGER { notSpecified(1), ascii(2), hex(3), ip-address(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the mode of the Vendor Specific Information, ascii(2) or hex(3) MUST be specified the content in dhcpPoolOptInetVendorSpecInfoBuffer, ip-address(4) MUST be specified the content in dhcpPoolOptInetVendorSpecInfoAddr." ::= { dhcpPoolOptInetVendorSpecInfoEntry 3 } dhcpPoolOptInetVendorSpecInfoBuffer OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..48)) MAX-ACCESS read-write STATUS current DESCRIPTION "Content of option 43 Vendor Specific Information. dhcpPoolOptInetVendorSpecInfoMode MUST be specified before setting this variable." ::= { dhcpPoolOptInetVendorSpecInfoEntry 4 } dhcpPoolOptInetVendorSpecInfoAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the INET address of the option 43 Vendor Specific Information. dhcpPoolOptInetVendorSpecInfoMode MUST be specified before setting this variable." ::= { dhcpPoolOptInetVendorSpecInfoEntry 5 } -- --pingMgt -- pingMgt OBJECT IDENTIFIER ::= { ipMgt 15 } pingIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the IP address of the device that is planned to ping." ::= { pingMgt 1 } pingPacketSize OBJECT-TYPE SYNTAX Integer32 (32..512) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the size of each data potion of ping packets in bytes." DEFVAL { 32 } ::= { pingMgt 2 } pingCompleted OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A value of true(1) will be read when this ping operation has been either responded to or changed to the time-out status. A value of false(2) will be read when there is a ping operation running and all associated objects in the pingMgt operation cannot be modified during this period." ::= { pingMgt 4 } pingAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), pingStart(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action of the pingMgt operation. Sets these objects to pingStart(2) to begin the ping operation. Once the action is set to pingStart(2), the associated pingMgt objects cannot be modified until this ping operation is completed (pingCompleted is true). When the ping has ended or there is no ping operation performing, this object will get a value of noAction(1)." ::= { pingMgt 5 } -- ASV3518KO-FLF-02, 2007-01, for CHT -- pingProbeCount OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the number of times to perform a ping operation at a remote host." ::= { pingMgt 6 } -- For CHT pingSentPackets OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reflects the number of probes sent. The value of this object must be reported as 0 when no probes have been sent." ::= { pingMgt 7 } pingReceivedPackets OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of responses received. The value of this object must be reported as 0 when no probe responses have been received." ::= { pingMgt 8 } -- For CHT pingPacketLossRate OBJECT-TYPE SYNTAX INTEGER(0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Packet loss rate of this ping operation. This variable is calculated by pingReceivedPackets and pingSentPackets. The rate is expressed as a percentage." ::= { pingMgt 9 } -- For CHT pingHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF PingHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the executive result information for the ping operation." ::= { pingMgt 10 } pingHistoryEntry OBJECT-TYPE SYNTAX PingHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the pingHistory table." INDEX { pingHistoryIndex } ::= { pingHistoryTable 1 } PingHistoryEntry::= SEQUENCE { pingHistoryIndex Integer32, pingHistoryResponse Integer32 } pingHistoryIndex OBJECT-TYPE SYNTAX Integer32(1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A new entry in this table is created when the result of a ping probe is determined. The old entries will be cleared when a new ping action is started." ::= { pingHistoryEntry 1 } pingHistoryResponse OBJECT-TYPE SYNTAX Integer32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This variable represents the round trip time and is measured in milliseconds. The variable is the difference between received time and sent time for a ping probe. If the difference value is more than the time-out value or no response is received, then the variable will be 5000 milliseconds." ::= { pingHistoryEntry 2 } dhcpOption82Status OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable DHCP Relay Option 82, set disabled(2) to disable it." ::= { dhcpOption82 1 } dhcpOption82Policy OBJECT-TYPE SYNTAX INTEGER { drop(1), replace(2), keep(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Provide three policies to handle packet" ::= { dhcpOption82 2 } dhcpOption82RemoteIDMode OBJECT-TYPE SYNTAX INTEGER { mac-address-in-hex(1), mac-address-in-ascii(2), ip-address-in-hex(3), ip-address-in-ascii(4), configured-string(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Provide five mode for insertion remote-id sub-option of option 82. If configured-string(5) has been set, dhcpOption82RemoteIDString will take effect." ::= { dhcpOption82 3 } dhcpOption82RemoteIDString OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set string to remote-id sub-option of option 82. It only take effect when dhcpOption82RemoteIDMode is set to configured-string(5)" ::= { dhcpOption82 4 } dhcpOption82EncodeFormat OBJECT-TYPE SYNTAX INTEGER { extra-subtype-included(1), no-extra-subtype-included(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set encode format for CID and RID in option82. Set extra-subtype-included(1) will have extra subtype and length field in CID and RID. Set no-extra-subtype-included(2) will only have TLV format for CID and RID." ::= { dhcpOption82 5 } dhcpOption82RelayServerAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpOption82RelayServerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table is to specify relay server IP address, the maximum number of server IP addresses user can specify is 5. " ::= { dhcpOption82 6 } dhcpOption82RelayServerAddrEntry OBJECT-TYPE SYNTAX DhcpOption82RelayServerAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of dhcpOption82RelayServerAddrTable." INDEX { dhcpOption82RelayServerAddrIndex } ::= { dhcpOption82RelayServerAddrTable 1 } DhcpOption82RelayServerAddrEntry ::= SEQUENCE { dhcpOption82RelayServerAddrIndex Integer32, dhcpOption82RelayServerAddrServerIp IpAddress } dhcpOption82RelayServerAddrIndex OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the relay server IP address." ::= { dhcpOption82RelayServerAddrEntry 1 } dhcpOption82RelayServerAddrServerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the relay server." ::= { dhcpOption82RelayServerAddrEntry 2 } -- -- vlanMgt -- -- Management for Virtual Local Area Network (VLAN). -- This has variables not already defined in the implemented -- standard MIB(s). vlanTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for VLAN configuration." ::= { vlanMgt 1 } vlanEntry OBJECT-TYPE SYNTAX VlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for VLAN configuration." INDEX { vlanIndex } ::= { vlanTable 1 } VlanEntry ::= SEQUENCE { vlanIndex Unsigned32, vlanAddressMethod INTEGER } vlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Based on dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface." ::= { vlanEntry 1 } vlanAddressMethod OBJECT-TYPE SYNTAX INTEGER { user(1), bootp(2), dhcp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Method to get the IP address." ::= { vlanEntry 2 } vlanPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in VLAN." ::= { vlanMgt 2 } vlanPortEntry OBJECT-TYPE SYNTAX VlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in VLAN." INDEX { vlanPortIndex } ::= { vlanPortTable 1 } VlanPortEntry ::= SEQUENCE { vlanPortIndex Integer32, vlanPortMode INTEGER, vlanPortPrivateVlanType INTEGER } vlanPortIndex OBJECT-TYPE SYNTAX Integer32(1..48) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qPvid in the Q-BRIDGE-MIB." ::= { vlanPortEntry 1 } vlanPortMode OBJECT-TYPE SYNTAX INTEGER { hybrid(1), dot1qTrunk(2), access(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) sets an access link." ::= { vlanPortEntry 2 } --¡@SYS_CPNT_COMMUNITY_PRIVATE_VLAN¡@(use PVLAN_MGR API) start vlanPortPrivateVlanType OBJECT-TYPE SYNTAX INTEGER { normal(1), isolated(2), community(3), promiscous(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port type defined for private VLAN." ::= { vlanPortEntry 3 } -- SYS_CPNT_COMMUNITY_PRIVATE_VLAN (use PVLAN_MGR API) end vlanDot1qTunnelGlobalConfig OBJECT IDENTIFIER ::= { vlanMgt 8 } vlanDot1qTunnelStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to globally enable/disable 802.1Q Tunneling on the device." ::= { vlanDot1qTunnelGlobalConfig 1 } vlanDot1qTunnelPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanDot1qTunnelPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in 802.1Q Tunneling." ::= { vlanMgt 9 } vlanDot1qTunnelPortEntry OBJECT-TYPE SYNTAX VlanDot1qTunnelPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in 802.1Q Tunneling." INDEX { vlanDot1qTunnelPortIndex } ::= { vlanDot1qTunnelPortTable 1 } VlanDot1qTunnelPortEntry ::= SEQUENCE { vlanDot1qTunnelPortIndex InterfaceIndex, vlanDot1qTunnelPortMode INTEGER, vlanDot1qTunnelPortEtherType Unsigned32, vlanDot1qTunnelPortPriorityMapStatus EnabledStatus } vlanDot1qTunnelPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { vlanDot1qTunnelPortEntry 1 } vlanDot1qTunnelPortMode OBJECT-TYPE SYNTAX INTEGER { none(1), access(2), uplink(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable sets the 802.1Q Tunneling mode. Setting it to none(1) indicates no mode in this port. Setting it to access(2) sets as dot1q-tunnel mode port which link to customer. Setting it to uplink(3) sets as dot1q-tunnel mode port which link to service-provider. If vlanDot1qTunnelStatus is disabled, it means vlanDot1qTunnelPortMode is inactive." ::= { vlanDot1qTunnelPortEntry 2 } vlanDot1qTunnelPortEtherType OBJECT-TYPE SYNTAX Unsigned32 ('0800'h..'ffff'h) MAX-ACCESS read-write STATUS current DESCRIPTION "TPID for 802.1Q encapsulation. It's used to select a nonstandard (nondefault) 2-byte ethertype to identify 802.1Q tagged frames." ::= { vlanDot1qTunnelPortEntry 3 } vlanDot1qTunnelPortPriorityMapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Status of priority mapping. Set to enabled(1) to use 802.1p priority of inner tag as packet's priority instead of using outer tag." ::= { vlanDot1qTunnelPortEntry 4 } -- -- voiceVlanMgt -- voiceVlanMgt OBJECT IDENTIFIER ::= { vlanMgt 6 } voiceVlanOuiTable OBJECT-TYPE SYNTAX SEQUENCE OF VoiceVlanOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the mac address which can be identified by Voice VLAN." ::= { voiceVlanMgt 1 } voiceVlanOuiEntry OBJECT-TYPE SYNTAX VoiceVlanOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the mac address which can be identified by Voice VLAN." INDEX { voiceVlanOuiAddress } ::= { voiceVlanOuiTable 1 } VoiceVlanOuiEntry ::= SEQUENCE { voiceVlanOuiAddress MacAddress, voiceVlanOuiMask MacAddress, voiceVlanOuiDescription DisplayString, voiceVlanOuiStatus ValidStatus } voiceVlanOuiAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address can be identified by voice vlan." ::= { voiceVlanOuiEntry 1 } voiceVlanOuiMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The mask of MAC address." ::= { voiceVlanOuiEntry 2 } voiceVlanOuiDescription OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "The description of OUI." ::= { voiceVlanOuiEntry 3 } voiceVlanOuiStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Current operation status of the row." ::= { voiceVlanOuiEntry 4 } voiceVlanEnabledId OBJECT-TYPE SYNTAX INTEGER (-1|1..4093) MAX-ACCESS read-write STATUS current DESCRIPTION "Voice VLAN enabled status and VLAN ID: enabled (1..4093), disabled (-1)." ::= { voiceVlanMgt 2 } voiceVlanAgingTime OBJECT-TYPE SYNTAX INTEGER (5..43200) MAX-ACCESS read-write STATUS current DESCRIPTION "Voice VLAN aging time, the unit of which is minute." DEFVAL { 1440 } ::= { voiceVlanMgt 3 } voiceVlanPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VoiceVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of voice VLAN port entries." ::= { voiceVlanMgt 7 } voiceVlanPortEntry OBJECT-TYPE SYNTAX VoiceVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing Voice VLAN port information, which is applicable to a Voice VLAN enabled interface." INDEX { voiceVlanPortIfIndex } ::= { voiceVlanPortTable 1 } VoiceVlanPortEntry ::= SEQUENCE { voiceVlanPortIfIndex Integer32, voiceVlanPortMode INTEGER, voiceVlanPortSecurity EnabledStatus, voiceVlanPortPriority INTEGER, voiceVlanPortRuleOui EnabledStatus, voiceVlanPortRuleLldp EnabledStatus, voiceVlanPortRemainAge DisplayString } voiceVlanPortIfIndex OBJECT-TYPE SYNTAX Integer32(1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of interface on which Voice VLAN function is enabled." REFERENCE "IfIndex in RFC1213." ::= { voiceVlanPortEntry 1 } voiceVlanPortMode OBJECT-TYPE SYNTAX INTEGER { auto (1), manual (2), none (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Voice VLAN configuration mode status." ::= { voiceVlanPortEntry 2 } voiceVlanPortSecurity OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "If the security is enabled, the port only allows voice traffic for the Voice VLAN." ::= { voiceVlanPortEntry 3 } voiceVlanPortPriority OBJECT-TYPE SYNTAX INTEGER(0..6) MAX-ACCESS read-write STATUS current DESCRIPTION "The priority of the voice vlan traffic in the port." ::= { voiceVlanPortEntry 4 } voiceVlanPortRuleOui OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The address of voice device is learned from OUI table." ::= { voiceVlanPortEntry 5 } voiceVlanPortRuleLldp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The address of voice device is learned from LLDP discovery." ::= { voiceVlanPortEntry 6 } voiceVlanPortRemainAge OBJECT-TYPE SYNTAX DisplayString (SIZE(1..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "Remaining aging time, the unit of which is minute." ::= { voiceVlanPortEntry 7 } -- -- macVlanMgt -- macVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MacVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the settings for MAC-based VLAN." ::= { vlanMgt 11 } macVlanEntry OBJECT-TYPE SYNTAX MacVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the macVlanTable." INDEX { macVlanMacMask, macVlanMacAddress } ::= { macVlanTable 1 } MacVlanEntry ::= SEQUENCE { macVlanMacAddress MacAddress, macVlanId VlanId, macVlanPriority Integer32, macVlanStatus ValidStatus, macVlanMacMask MacAddress } macVlanMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address that may specify an entry in the table which contains MAC-based VLAN information." ::= { macVlanEntry 1 } macVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the VLAN ID which the MAC address associates with." ::= { macVlanEntry 2 } macVlanPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the priority whcich the MAC address associates with." ::= { macVlanEntry 3 } macVlanStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry." ::= { macVlanEntry 4 } macVlanMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address mask that may specify an entry in the table which contains MAC-based VLAN information." ::= { macVlanEntry 5 } macVlanClearAction OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for clearing macVlanTable. When this object is set to clear(2), all entries in macVlanTable will be cleared. When this object is read, the value of this object is always noClear(1)." ::= { vlanMgt 12 } -- -- subnetVlanMgt -- subnetVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF SubnetVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the settings for IP subnet-based VLAN." ::= { vlanMgt 13 } subnetVlanEntry OBJECT-TYPE SYNTAX SubnetVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the subnetVlanTable." INDEX { subnetVlanMask, subnetVlanIpAddress } ::= { subnetVlanTable 1 } SubnetVlanEntry ::= SEQUENCE { subnetVlanIpAddress IpAddress, subnetVlanMask IpAddress, subnetVlanId Integer32, subnetVlanPriority Integer32, subnetVlanStatus ValidStatus } subnetVlanIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IPv4 address of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanMask object is not equal to x." ::= { subnetVlanEntry 1 } subnetVlanMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The netmask of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanIpAddress object is not equal to subnetVlanIpAddress." ::= { subnetVlanEntry 2 } subnetVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the VLAN ID which the subnet associates with." ::= { subnetVlanEntry 3 } subnetVlanPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the priority whcich the subnet associates with." ::= { subnetVlanEntry 4 } subnetVlanStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry." ::= { subnetVlanEntry 5 } subnetVlanClearAction OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for clearing subnetVlanTable. When this object is set to clear(2), all entries in subnetVlanTable will be cleared. When this object is read, the value of this object is always noClear(1)." ::= { vlanMgt 14 } -- vlanStaticExtTable vlanStaticExtTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanStaticExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension table of dot1qVlanStaticTable. This table enhances the original table with extra vlanStaticExtRspanStatus to create and destroy RSPAN VLAN(s)." ::= { vlanMgt 15 } vlanStaticExtEntry OBJECT-TYPE SYNTAX VlanStaticExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the vlanStaticExtTable." AUGMENTS { dot1qVlanStaticEntry } ::= { vlanStaticExtTable 1 } VlanStaticExtEntry ::= SEQUENCE { vlanStaticExtRspanStatus INTEGER } vlanStaticExtRspanStatus OBJECT-TYPE SYNTAX INTEGER { destroy(1), vlan(2), rspanVlan(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Displays type of a VLAN is vlan(2) or rspanVlan(3). Set this to destroy(1) to destroy a RSPAN VLAN. Set this to rspanVlan(3) to create a RSPAN VLAN. Setting this to vlan(2) is not allowed." ::= { vlanStaticExtEntry 1 } -- -- vlanL2ProtocolTunnelPortTable -- vlanL2ProtocolTunnelPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanL2ProtocolTunnelPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in Layer 2 Protocol Tunneling." ::= { vlanMgt 16 } vlanL2ProtocolTunnelPortEntry OBJECT-TYPE SYNTAX VlanL2ProtocolTunnelPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in Layer 2 Protocol Tunneling." INDEX { vlanL2ptPortIndex } ::= { vlanL2ProtocolTunnelPortTable 1 } VlanL2ProtocolTunnelPortEntry ::= SEQUENCE { vlanL2ptPortIndex InterfaceIndex, vlanL2ptPortSta EnabledStatus, vlanL2ptPortLldp EnabledStatus, vlanL2ptPortCdp EnabledStatus, vlanL2ptPortVtp EnabledStatus, vlanL2ptPortPvst EnabledStatus, vlanL2ptPortLacp EnabledStatus } vlanL2ptPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { vlanL2ProtocolTunnelPortEntry 1 } vlanL2ptPortSta OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set enabled(1) to enable Layer 2 protocol tunneling for spanning-tree protocol. Set disabled(2) to disable Layer 2 protocol tunneling for spanning-tree protocol." ::= { vlanL2ProtocolTunnelPortEntry 2 } vlanL2ptPortLldp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable Layer 2 protocol tunneling for LLDP. Set disabled(2) to disable Layer 2 protocol tunneling for LLDP." ::= { vlanL2ProtocolTunnelPortEntry 3 } vlanL2ptPortCdp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable Layer 2 protocol tunneling for Cisco Discovery Protocol. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco Discovery Protocol." ::= { vlanL2ProtocolTunnelPortEntry 4 } vlanL2ptPortVtp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable Layer 2 protocol tunneling for Cisco VTP. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco VTP." ::= { vlanL2ProtocolTunnelPortEntry 5 } vlanL2ptPortPvst OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable Layer 2 protocol tunneling for Cisco PVST+. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco PVST+." ::= { vlanL2ProtocolTunnelPortEntry 6 } vlanL2ptPortLacp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable Layer 2 protocol tunneling for LACP. Set disabled(2) to disable Layer 2 protocol tunneling for LACP." ::= { vlanL2ProtocolTunnelPortEntry 7 } -- -- vlanL2ProtocolTunnelGlobalConfig -- vlanL2ProtocolTunnelGlobalConfig OBJECT IDENTIFIER ::= { vlanMgt 19 } vlanL2ProtocolTunnelAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination MAC address for PDU tunneling." ::= { vlanL2ProtocolTunnelGlobalConfig 1 } -- -- L2/L3 VLAN Mgt -- vlanStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for static VLAN configuration including VLAN aggregation support." ::= { vlanMgt 17 } vlanStaticEntry OBJECT-TYPE SYNTAX VlanStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Static information for a VLAN configured on the device by (local or network) management." INDEX { vlanStaticIndex } ::= { vlanStaticTable 1 } VlanStaticEntry ::= SEQUENCE { vlanStaticIndex VlanIndex, vlanStaticInterfaceType INTEGER } vlanStaticIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID of the VLAN." ::= { vlanStaticEntry 1 } vlanStaticInterfaceType OBJECT-TYPE SYNTAX INTEGER { l2vlan(135), l3ipvlan(136) } MAX-ACCESS read-create STATUS current DESCRIPTION "The interface type of the VLAN (there is a subtype of IANAifType). l2vlan(135) refers to L2 interface and can't accept any L3 related configuration. l3ipvlan(136) refers to L3 interface and can accept L3 related configuration." DEFVAL { l2vlan } ::= { vlanStaticEntry 2 } vlanDot1qTunnelSrvCvidPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanDot1qTunnelSrvCvidPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration to specify how to insert outer tag by matching customer VLAN ID." ::= { vlanMgt 18 } vlanDot1qTunnelSrvCvidPortEntry OBJECT-TYPE SYNTAX VlanDot1qTunnelSrvCvidPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration to specify how to insert outer tag by matching customer VLAN ID." INDEX { vlanDot1qTunnelSrvCvidPortIndex, vlanDot1qTunnelSrvCvidPortCvid } ::= { vlanDot1qTunnelSrvCvidPortTable 1 } VlanDot1qTunnelSrvCvidPortEntry ::= SEQUENCE { vlanDot1qTunnelSrvCvidPortIndex InterfaceIndex, vlanDot1qTunnelSrvCvidPortCvid VlanIndex, vlanDot1qTunnelSrvCvidPortSvid VlanId, vlanDot1qTunnelSrvCvidPortStatus ValidStatus, vlanDot1qTunnelSrvCvidPortAction BITS } vlanDot1qTunnelSrvCvidPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port interface of the vlanDot1qTunnelSrvCvidPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { vlanDot1qTunnelSrvCvidPortEntry 1 } vlanDot1qTunnelSrvCvidPortCvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies customer VLAN ID." ::= { vlanDot1qTunnelSrvCvidPortEntry 2 } vlanDot1qTunnelSrvCvidPortSvid OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies service VLAN ID." ::= { vlanDot1qTunnelSrvCvidPortEntry 3 } vlanDot1qTunnelSrvCvidPortStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Sets to valid(1) to create an entry. Sets to invalid(2) to destroy an entry." ::= { vlanDot1qTunnelSrvCvidPortEntry 5 } vlanDot1qTunnelSrvCvidPortAction OBJECT-TYPE SYNTAX BITS { reserved0(0), reserved1(1), assignSvid(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Sets to assignSvid(2) to assign service VLAN ID." ::= { vlanDot1qTunnelSrvCvidPortEntry 6 } -- -- vlanTranslationMgt -- vlanTraslationPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanTraslationPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of VLAN translation entries." ::= { vlanMgt 22 } vlanTraslationPortEntry OBJECT-TYPE SYNTAX VlanTraslationPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration to set up VLAN translation mapping." INDEX { vlanTraslationPortIndex, vlanTraslationPortOldVid } ::= { vlanTraslationPortTable 1 } VlanTraslationPortEntry ::= SEQUENCE { vlanTraslationPortIndex InterfaceIndex, vlanTraslationPortOldVid VlanIndex, vlanTraslationPortNewVid VlanId, vlanTraslationPortStatus ValidStatus } vlanTraslationPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port interface of vlanTraslationPortIndex. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { vlanTraslationPortEntry 1 } vlanTraslationPortOldVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN translation is applied in both ingress and egress sides of the port. It makes the traffic arriving on the VLAN with this VLAN ID to be mapped to or tagged with the corresponding instance of vlanTraslationPortNewVid on the port. It also causes all the traffic internally tagged with the corresponding instance of vlanTraslationPortNewVid and leaving the port to be tagged with the VLAN of this VLAN ID." ::= { vlanTraslationPortEntry 2 } vlanTraslationPortNewVid OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the new VLAN ID that will be mapped to." ::= { vlanTraslationPortEntry 3 } vlanTraslationPortStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Sets to valid(1) to create an entry. Sets to invalid(2) to destroy an entry." ::= { vlanTraslationPortEntry 4 } -- -- priorityMgt -- -- Management for traffic priority. This allows a user -- to specify which data packets have greater precedence -- when traffic is buffered in the switch due to congestion. prioIpPrecDscpStatus OBJECT-TYPE SYNTAX INTEGER { disabled(1), precedence(2), dscp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Selects whether no frame priority mapping, IP ToS precedence mapping or DSCP mapping is performed." ::= { priorityMgt 1 } prioIpDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioIpDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for IP DSCP priority mapping." ::= { priorityMgt 4 } prioIpDscpEntry OBJECT-TYPE SYNTAX PrioIpDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for IP DSCP priority mapping." INDEX { prioIpDscpPort, prioIpDscpValue } ::= { prioIpDscpTable 1 } PrioIpDscpEntry ::= SEQUENCE { prioIpDscpPort InterfaceIndex, prioIpDscpValue Integer32, prioIpDscpCos Integer32 } prioIpDscpPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioIpDscpEntry 1 } prioIpDscpValue OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Value of IP DSCP as specified in the packet header." ::= { prioIpDscpEntry 2 } prioIpDscpCos OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Class of Service as defined by dot1dTrafficClassPriority in the P-BRIDGE-MIB. The prioIpDscpValue value in the same table row will be mapped to this Class of Service (CoS). This CoS is then further mapped to the hardware queue according to dot1dTrafficClassTable." REFERENCE "P-BRIDGE-MIB.dot1dPriority.dot1dTrafficClassTable." ::= { prioIpDscpEntry 3 } prioIpDscpRestoreDefault OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Enables the IP DSCP settings of a port to be reset to their defaults. To reset the IP DSCP settings of a port, assign the value of the relevant ifIndex defined by the ifIndex in the IF-MIB. For example, assigning the value 1 will result in the IP DSCP settings of port 1 being restored to their default. 0 will always be obtained when reading this variable" ::= { priorityMgt 5 } -- optional prioCopy OBJECT IDENTIFIER ::= { priorityMgt 8 } prioCopyIpDscp OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port in high-to-low (big-endian) order. Starting from the 5th octet is the destination port list in a form described by PortList in the Q-BRIDGE-MIB. Writing this object will perform copy. Reading this object will always get a zero-length octet string." ::= { prioCopy 2 } prioWrrTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioWrrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for weighted round robin (WRR)." ::= { priorityMgt 9 } prioWrrEntry OBJECT-TYPE SYNTAX PrioWrrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for weighted round robin (WRR)." INDEX { prioWrrTrafficClass } ::= { prioWrrTable 1 } PrioWrrEntry ::= SEQUENCE { prioWrrTrafficClass Integer32, prioWrrWeight Integer32 } prioWrrTrafficClass OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1." REFERENCE "MIB.IETF|P-BRIDGE-MIB.dot1dTrafficClass." ::= { prioWrrEntry 1 } prioWrrWeight OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Weight for this entry." ::= { prioWrrEntry 2 } prioQueueMode OBJECT-TYPE SYNTAX INTEGER { wrr(1), strict(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The global status for the prioQueue. wrr(1),strict(2)" ::= { priorityMgt 10 } -- trapDestMgt -- -- trapVar is for binding variables for traps, there is no value when -- no trap is sent. trapVar OBJECT IDENTIFIER ::= { trapDestMgt 2 } -- For IP Filter Reject trapIpFilterRejectMode OBJECT-TYPE SYNTAX INTEGER { web(1), snmp(2), telnet(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is for trap var binding, indicated the ipfilter reject mode. web(1), snmp(2), telnet(3)." ::= { trapVar 6 } trapIpFilterRejectIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is for trap var binding, indicating the IP address that rejected by the ipfilter." ::= { trapVar 7 } trapTcnReason OBJECT-TYPE SYNTAX INTEGER { pushButton(1), stackingLinkDown(2), stackingLinkUp(3), hbtTimeout(4), hbtError(5) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The variable represents the function of TCN: pushButton(1): Push button to enable the unit as the Master unit in the stack. stackingLinkDown(2): Stacking link is down. stackingLinkUp(3): Stacking link is up. hbtTimeout(4): Control packet sent from the Master through all units has timed-out. hbtError(5): Control packet sent from the Master through all units was received with errors." ::= { trapVar 9 } trapVarMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The MAC address." ::= { trapVar 10 } trapVarLoginUserName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..8)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The name of the user who logs into the switch." ::= { trapVar 11 } trapVarSessionType OBJECT-TYPE SYNTAX INTEGER { web(1), -- deprecated; use http(6) and https(7) snmp(2), telnet(3), console(4), ssh(5), http(6), https(7) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The method by which the user logs in to control the switch." ::= { trapVar 12 } trapVarLoginInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The address type of the address associated with this agent. Only IPv4 and IPv6 types are supported." ::= { trapVar 15 } trapVarLoginInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The IP address from which the user logs into the switch." ::= { trapVar 16 } trapIpFilterRejectInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is for trap var binding, indicating the IP address that was rejected by the IP filter." ::= { trapVar 17 } trapIpFilterRejectInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is for trap var binding, indicating the IP address that was rejected by the IP filter." ::= { trapVar 18 } --For Auto Upgrade trapAutoUpgradeResult OBJECT-TYPE SYNTAX INTEGER { succeeded(1), failed(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates which result triggers the trap." ::= { trapVar 22 } trapAutoUpgradeNewVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates new version which was upgraded to. When trapAutoUpgradeResult was failed(2), it would be null string." ::= { trapVar 23 } trapIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is for trap var binding, indicating the index of an interface." ::= { trapVar 30 } trapVlanId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is for trap var binding, indicating the identifier of a VLAN." ::= { trapVar 31 } -- For DHCP rogue server attack trapDhcpClientPortIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "ifIndex for the port connected to DHCP rogue server." ::= { trapVar 62 } trapDhcpServerIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The IP address of the rogue server." ::= { trapVar 63 } -- For SFP's alarm/warning type trapSfpThresholdAlarmWarnIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "ifIndex for the port issued alarm/warning trap." ::= { trapVar 64 } trapSfpThresholdAlarmWarnType OBJECT-TYPE SYNTAX INTEGER { rxPowerHighAlarm(1), rxPowerLowAlarm(2), rxPowerHighWarning(3), rxPowerLowWarning(4), txPowerHighAlarm(5), txPowerLowAlarm(6), txPowerHighWarning(7), txPowerLowWarning(8), temperatureHighAlarm(9), temperatureLowAlarm(10), temperatureHighWarning(11), temperatureLowWarning(12), voltageHighAlarm(13), voltageLowAlarm(14), voltageHighWarning(15), voltageLowWarning(16), currentHighAlarm(17), currentLowAlarm(18), currentHighWarning(19), currentLowWarning(20), rxPowerAlarmWarnCease(21), txPowerAlarmWarnCease(22), temperatureAlarmWarnCease(23), voltageAlarmWarnCease(24), currentAlarmWarnCease(25) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "SFP's alarm/warning type ." ::= { trapVar 65 } -- For UDLD trapUdldPortShutdownReason OBJECT-TYPE SYNTAX INTEGER { unidirectionalLink(1), mismatchWithNeighbor(2), transmitToReceiveLoop(3), aggressiveModeFailure(4) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is for trap var binding, indicated the reason for the UDLD port shutdown. unidirectionalLink(1): unidirectional link detected, mismatchWithNeighbor(2): mismatch with neighbor state reported. transmitToReceiveLoop(3): transmit-to-receive loop detected. aggressiveModeFailure(4): aggressive mode failure detected." ::= { trapVar 66 } trapDhcpServerMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The MAC address of the rogue server." ::= { trapVar 67 } trapMacNotifyAction OBJECT-TYPE SYNTAX INTEGER { add(1), remove(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates which result triggers the trap." ::= { trapVar 68 } trapTcnStackingUnitIndex OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This parameter identifies which unit triggered this TCN trap." ::= { trapVar 69 } trapTcnStackingUnitRole OBJECT-TYPE SYNTAX INTEGER { master(1), slave(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates the role of this unit is master or slave." ::= { trapVar 70 } trapTcnStackingTplg OBJECT-TYPE SYNTAX INTEGER { ring(1), line(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates current stacking topology is ring or line." ::= { trapVar 71 } trapTcnStackingUpPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates the up-link stacking port id." ::= { trapVar 72 } trapTcnStackingUpPortLinkStatus OBJECT-TYPE SYNTAX INTEGER { linkUp(1), linkDown(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates current link status of up-link stacking port." ::= { trapVar 73 } trapTcnStackingUpPortLinkStatusChanged OBJECT-TYPE SYNTAX INTEGER { noChanged(0), changed(1) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates the link status of up-link stacking port is changed." ::= { trapVar 74 } trapTcnStackingDownPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates the down-link stacking port id." ::= { trapVar 75 } trapTcnStackingDownPortLinkStatus OBJECT-TYPE SYNTAX INTEGER { linkUp(1), linkDown(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates current link status of down-link stacking port." ::= { trapVar 76 } trapTcnStackingDownPortLinkStatusChanged OBJECT-TYPE SYNTAX INTEGER { noChanged(0), changed(1) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The parameter indicates the link status of down-link stacking port is changed." ::= { trapVar 77 } trapStackingUnitIndex OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This parameter indicates which unit is inserted/removed." ::= { trapVar 81 } trapStackingUnitInsertRemove OBJECT-TYPE SYNTAX INTEGER { inserted(1), removed(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This parameter indicates unit is inserted or removed." ::= { trapVar 82 } -- -- qosMgt -- -- Management for Quality of Service (QoS) for network traffic. -- -- rateLimitMgt -- -- optional rateLimitMgt OBJECT IDENTIFIER ::= { qosMgt 1 } rateLimitPortTable OBJECT-TYPE SYNTAX SEQUENCE OF RateLimitPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for rate limit of each port." ::= { rateLimitMgt 2 } rateLimitPortEntry OBJECT-TYPE SYNTAX RateLimitPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for rate limit of each port." INDEX { rlPortIndex } ::= { rateLimitPortTable 1 } RateLimitPortEntry ::= SEQUENCE { rlPortIndex InterfaceIndex, rlPortInputStatus EnabledStatus, rlPortOutputStatus EnabledStatus, rlPortInputLimitInKilo Integer32, rlPortOutputLimitInKilo Integer32 } rlPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { rateLimitPortEntry 1 } -- all need (both acd and non-acd) rlPortInputStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether input rate limit is enabled for this port." ::= { rateLimitPortEntry 6 } -- all need (both acd and non-acd) rlPortOutputStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether output rate limit is enabled for this port." ::= { rateLimitPortEntry 7 } rlPortInputLimitInKilo OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Value of the input rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000." ::= { rateLimitPortEntry 10 } rlPortOutputLimitInKilo OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Value of the output rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000." ::= { rateLimitPortEntry 11 } cosMgt OBJECT IDENTIFIER ::= { qosMgt 3 } --prioAclToCosMappingTable prioAclToCosMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioAclToCosMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for ACL to CoS Mapping." ::= { cosMgt 1 } prioAclToCosMappingEntry OBJECT-TYPE SYNTAX PrioAclToCosMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for ACL to CoS Mapping." INDEX { prioAclToCosMappingIfIndex, prioAclToCosMappingAclName } ::= { prioAclToCosMappingTable 1 } PrioAclToCosMappingEntry ::= SEQUENCE { prioAclToCosMappingIfIndex InterfaceIndex, prioAclToCosMappingAclName DisplayString, prioAclToCosMappingCosValue Integer32, prioAclToCosMappingStatus RowStatus } prioAclToCosMappingIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port interface of the prioAclToCosMappingEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioAclToCosMappingEntry 1 } prioAclToCosMappingAclName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of an IP ACL. Within a feature a unique name is used to identify the list to which the entry belongs in the device." ::= { prioAclToCosMappingEntry 2 } prioAclToCosMappingCosValue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "CoS value of the prioAclToCosMappingTable." ::= { prioAclToCosMappingEntry 3 } prioAclToCosMappingStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { prioAclToCosMappingEntry 4 } prioIfClassificationModeTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioIfClassificationModeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for setting the interface Qos mapping classification mode." ::= { cosMgt 2 } prioIfClassificationModeEntry OBJECT-TYPE SYNTAX PrioIfClassificationModeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for setting the interface Qos mapping classification mode." INDEX { prioIfClassificationModeIf } ::= { prioIfClassificationModeTable 1 } PrioIfClassificationModeEntry ::= SEQUENCE { prioIfClassificationModeIf InterfaceIndex, prioIfClassificationModeStatus INTEGER } prioIfClassificationModeIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioIfClassificationModeEntry 1 } prioIfClassificationModeStatus OBJECT-TYPE SYNTAX INTEGER { cos(0), ipPrecedence(1), dscp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Qos mapping classification mode of the interface. cos mode means that the internal priority is mapped from priority field of packet's VLAN tag if a VLAN tag exists; IP precedence mode means that the internal priority is mapped from the IP precedence value of IP packets; DSCP mode means the internal priority is mapped from the dscp value of IP packets." ::= { prioIfClassificationModeEntry 2 } -- -- The mapping table from CoS/CFI to internal QoS label -- prioCosToDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioCosToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for CoS/CFI to internal QoS label mapping." ::= { cosMgt 3 } prioCosToDscpEntry OBJECT-TYPE SYNTAX PrioCosToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for CoS/CFI to internal QoS label mapping." INDEX { prioCosToDscpIfValue, prioCosToDscpCosValue, prioCosToDscpCFIValue } ::= { prioCosToDscpTable 1 } PrioCosToDscpEntry ::= SEQUENCE { prioCosToDscpIfValue InterfaceIndex, prioCosToDscpCosValue Integer32, prioCosToDscpCFIValue Integer32, prioCosToDscpDscpValue Integer32 } prioCosToDscpIfValue OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or the trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioCosToDscpEntry 1 } prioCosToDscpCosValue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CoS value (0~7) mapped to an internal QoS label value which is composed of PHB(3 bits) and drop precedence(2 bits)." ::= { prioCosToDscpEntry 2 } prioCosToDscpCFIValue OBJECT-TYPE SYNTAX Integer32 (0..1) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CFI value (0 or 1) mapped to an internal QoS label value which is composed of PHB(3 bits) and drop precedence(2 bits)." ::= { prioCosToDscpEntry 3 } prioCosToDscpDscpValue OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "The DSCP value used to represent the internal QoS label (3 bits PHB+2 bits Drop precedence). The MSB 4 bits of DSCP is used to represent PHB value of QoS label; The LSB 2 bits of DSCP are used to represent the drop precedence value of QoS label. Green(0), Yellow(3), Red(1). In a word, PHB=(DSCP>>2), Drop precedence=(DSCP & 0x3). Note: The setting range of PHB value must be 0~7 and the setting drop precedence value must be one of the values (0,1,3)." ::= { prioCosToDscpEntry 4 } -- -- The mapping table from IP precedence to internal Qos label -- prioPrecToDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioPrecToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for IP precedence to internal QoS label mapping. This table setting will take effect only when the interface QoS mapping classification mode is set to IP precedence mode." ::= { cosMgt 4 } prioPrecToDscpEntry OBJECT-TYPE SYNTAX PrioPrecToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for IP precedence to internal QoS label mapping." INDEX { prioPrecToDscpIfValue, prioPrecToDscpPrecValue } ::= { prioPrecToDscpTable 1 } PrioPrecToDscpEntry ::= SEQUENCE { prioPrecToDscpIfValue InterfaceIndex, prioPrecToDscpPrecValue Integer32, prioPrecToDscpDscpValue Integer32 } prioPrecToDscpIfValue OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioPrecToDscpEntry 1 } prioPrecToDscpPrecValue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP precedence value mapped to internal QoS label value which is composed of PHB (3 bits) and drop precedence (2 bits)." ::= { prioPrecToDscpEntry 2 } prioPrecToDscpDscpValue OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "The DSCP value used to represent internal QoS label (3 bits PHB + 2 bits Drop precedence). The MSB 4 bits of DSCP are used to represent PHB value of QoS label; The LSB 2 bits of DSCP are used to represent the drop precedence value of QoS label. Green(0),Yellow(3), Red(1). In a word, PHB=(DSCP>>2), Drop precedence=(DSCP & 0x3). Note: The setting range of PHB value must be 0~7 and the setting drop precedence value must be one of values(0,1,3)." ::= { prioPrecToDscpEntry 3 } -- -- The mapping table from DSCP to internal Qos label -- prioDscpToDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioDscpToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for DSCP to internal QoS label mapping. This table setting will take effect only when the interface Qos mapping classification mode is set to DSCP mode." ::= { cosMgt 5 } prioDscpToDscpEntry OBJECT-TYPE SYNTAX PrioDscpToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for ingress DSCP to internal QoS label mapping." INDEX { prioDscpToDscpIfValue, prioDscpToDscpIngressDscpValue } ::= { prioDscpToDscpTable 1 } PrioDscpToDscpEntry ::= SEQUENCE { prioDscpToDscpIfValue InterfaceIndex, prioDscpToDscpIngressDscpValue Integer32, prioDscpToDscpDscpValue Integer32 } prioDscpToDscpIfValue OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioDscpToDscpEntry 1 } prioDscpToDscpIngressDscpValue OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ingress DSCP value which will be mapped to internal QoS label value." ::= { prioDscpToDscpEntry 2 } prioDscpToDscpDscpValue OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "The DSCP value used to represent internal QoS label (3 bits PHB + 2 bits Drop precedence). The MSB 4 bits of DSCP are used to represent PHB value of Qos label. The LSB 2 bits of DSCP are used to represent the drop precedence value of QoS label. Green(0),Yellow(3), Red(1). In a word, PHB=(DSCP>>2), Drop precedence=(DSCP & 0x3). Note: The setting range of PHB value must be 0~7 and the setting drop precedence value must be one of values (0,1,3)." ::= { prioDscpToDscpEntry 3 } -- -- The mapping table from TCP/UDP destination port number to internal Qos label -- prioDstPortToDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioDstPortToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for TCP/UDP destination port number to internal Qos label mapping. This table setting will always take effect for TCP/UDP packets no matter of what interface QoS mapping classification mode is set." ::= { cosMgt 6 } prioDstPortToDscpEntry OBJECT-TYPE SYNTAX PrioDstPortToDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for TCP/UDP destination port to internal QoS label mapping." INDEX { prioDstPortToDscpIfValue, prioDstPortToDscpProtocolValue, prioDstPortToDscpDstPortValue } ::= { prioDstPortToDscpTable 1 } PrioDstPortToDscpEntry ::= SEQUENCE { prioDstPortToDscpIfValue InterfaceIndex, prioDstPortToDscpProtocolValue INTEGER, prioDstPortToDscpDstPortValue Integer32, prioDstPortToDscpDscpValue Integer32 } prioDstPortToDscpIfValue OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or the trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioDstPortToDscpEntry 1 } prioDstPortToDscpProtocolValue OBJECT-TYPE SYNTAX INTEGER { tcp(6), udp(17) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The protocol value (TCP:6, UDP:17) which will be mapped to internal QoS label value." ::= { prioDstPortToDscpEntry 2 } prioDstPortToDscpDstPortValue OBJECT-TYPE SYNTAX Integer32(1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination port number value which will be mapped to internal QoS label value." ::= { prioDstPortToDscpEntry 3 } prioDstPortToDscpDscpValue OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "The DSCP value used to represent internal QoS label (3 bits PHB + 2 bits Drop precedence). The MSB 4 bits of DSCP is used to represent PHB value of QoS label. The LSB 2 bits of DSCP is used to represent the drop precedence value of Qos label. Green(0),Yellow(3), Red(1). In a word, PHB=(DSCP>>2), Drop precedence=(DSCP & 0x3). Note: The setting range of PHB value must be 0~7 and the setting drop precedence value must be one of values (0,1,3)." ::= { prioDstPortToDscpEntry 4 } -- -- The mapping table from internal Qos label to CoS and CFI -- prioDscpToCosTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioDscpToCosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for internal QoS label to CoS and CFI mapping." ::= { cosMgt 7 } prioDscpToCosEntry OBJECT-TYPE SYNTAX PrioDscpToCosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for internal QoS label to CoS and CFI mapping." INDEX { prioDscpToCosIfValue, prioDscpToCosPHBValue, prioDscpToCosDropPrecedenceValue } ::= { prioDscpToCosTable 1 } PrioDscpToCosEntry ::= SEQUENCE { prioDscpToCosIfValue InterfaceIndex, prioDscpToCosPHBValue Integer32, prioDscpToCosDropPrecedenceValue INTEGER, prioDscpToCosCFICosValue Integer32 } prioDscpToCosIfValue OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioDscpToCosEntry 1 } prioDscpToCosPHBValue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PHB value of internal QoS label." ::= { prioDscpToCosEntry 2 } prioDscpToCosDropPrecedenceValue OBJECT-TYPE SYNTAX INTEGER { green(0), red(1), yellow(3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The drop precedence value of internal QoS label. Green(0), Yellow(3), Red(1)." ::= { prioDscpToCosEntry 3 } prioDscpToCosCFICosValue OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "The remarked CFI and CoS value mapped from the internal Qos label value when the packet leaves the device. The egress remarked CFI value equals to (prioDscpToCosCFICosValue >>3) and the egress remarked CoS value equals to (prioDscpToCosCFICosValue & 0x7)." ::= { prioDscpToCosEntry 4 } -- The mapping table for packet priority to drop precedence mapping. prioPrioToDropPrecTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioPrioToDropPrecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for packet priority to drop precedence mapping." ::= { cosMgt 8 } prioPrioToDropPrecEntry OBJECT-TYPE SYNTAX PrioPrioToDropPrecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for packet priority to drop precedence mapping." INDEX { prioPrioToDropPrecIfValue, prioPrioToDropPrecPriorityValue } ::= { prioPrioToDropPrecTable 1 } PrioPrioToDropPrecEntry ::= SEQUENCE { prioPrioToDropPrecIfValue InterfaceIndex, prioPrioToDropPrecPriorityValue Integer32, prioPrioToDropPrecPrecValue INTEGER } prioPrioToDropPrecIfValue OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or the trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioPrioToDropPrecEntry 1 } prioPrioToDropPrecPriorityValue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of packet default priority." ::= { prioPrioToDropPrecEntry 2 } prioPrioToDropPrecPrecValue OBJECT-TYPE SYNTAX INTEGER { green(0), red(1), yellow(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The drop precedence value of internal QoS label. Green(0),Yellow(3), Red(1)." ::= { prioPrioToDropPrecEntry 3 } -- The mapping table from PHB to queue -- prioDscpToQueueTable OBJECT-TYPE SYNTAX SEQUENCE OF PrioDscpToQueueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for PHB to queue mapping." ::= { cosMgt 9 } prioDscpToQueueEntry OBJECT-TYPE SYNTAX PrioDscpToQueueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for PHB to queue mapping." INDEX { prioDscpToQueueIfValue, prioDscpToQueuePHBValue } ::= { prioDscpToQueueTable 1 } PrioDscpToQueueEntry ::= SEQUENCE { prioDscpToQueueIfValue InterfaceIndex, prioDscpToQueuePHBValue Integer32, prioDscpToQueueQueueValue Integer32 } prioDscpToQueueIfValue OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { prioDscpToQueueEntry 1 } prioDscpToQueuePHBValue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PHB value of internal QoS label." ::= { prioDscpToQueueEntry 2 } prioDscpToQueueQueueValue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The queue value which is mapped from the PHB value of QoS label." ::= { prioDscpToQueueEntry 3 } -- --diffServMgt -- diffServMgt OBJECT IDENTIFIER ::= { qosMgt 4 } diffServPolicyMapTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServPolicyMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for policy map." ::= { diffServMgt 10 } diffServPolicyMapEntry OBJECT-TYPE SYNTAX DiffServPolicyMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for policy map." INDEX { diffServPolicyMapIndex } ::= { diffServPolicyMapTable 1 } DiffServPolicyMapEntry ::= SEQUENCE { diffServPolicyMapIndex Integer32, diffServPolicyMapName DisplayString, diffServPolicyMapDescription DisplayString, diffServPolicyMapElementIndexList OCTET STRING, diffServPolicyMapStatus RowStatus } diffServPolicyMapIndex OBJECT-TYPE SYNTAX Integer32(1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in this table." ::= { diffServPolicyMapEntry 1 } diffServPolicyMapName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this entry." ::= { diffServPolicyMapEntry 2 } diffServPolicyMapDescription OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The description of this entry." ::= { diffServPolicyMapEntry 3 } diffServPolicyMapElementIndexList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string containes the diffServPolicyMapElementEntry indexes. Two octets express one index and it is represented in network order. This index list indicates the diffServPolicyMapEntrys which belong to this entry." ::= { diffServPolicyMapEntry 4 } diffServPolicyMapStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active');it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServPolicyMapEntry 5 } diffServPolicyMapAttachCtl OBJECT IDENTIFIER ::= { diffServMgt 11 } diffServPolicyMapAttachCtlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index for attachment control. Specifies the policy map as the target to relate with the policy map element. The policy map identified by a particular value of this index is associated with the same diffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex." ::= { diffServPolicyMapAttachCtl 1 } diffServPolicyMapAttachCtlElementIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Element Index for attachment control.Specifies the policy map element to relate with the policy map. The policy map element identified by a particular value of this index is associated with the same diffServPolicyMapElementEntry as identified by the same value of diffServPolicyMapElementIndex." ::= { diffServPolicyMapAttachCtl 2 } diffServPolicyMapAttachCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), attach(2), detach(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular policy map element is attached to a particular policy map. When setting this object to detach(3) to begin the not attached operation, a particular policy map element is not attached to a particular policy map. When the action is finshed or no action is taken, the value of this object is noAction(1). A particular policy map is specified in the diffServPolicyMapAttachCtlIndex. A particularpolicy map element is specified in the diffServPolicyMapAttachCtlElementIndex." ::= { diffServPolicyMapAttachCtl 3 } diffServPolicyMapElementTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServPolicyMapElementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for policy map element." ::= { diffServMgt 12 } diffServPolicyMapElementEntry OBJECT-TYPE SYNTAX DiffServPolicyMapElementEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for policy map element." INDEX { diffServPolicyMapElementIndex } ::= { diffServPolicyMapElementTable 1 } DiffServPolicyMapElementEntry ::= SEQUENCE { diffServPolicyMapElementIndex Integer32, diffServPolicyMapElementClassMapIndex Integer32, diffServPolicyMapElementMeterIndex Integer32, diffServPolicyMapElementActionIndex Integer32, diffServPolicyMapElementStatus RowStatus } diffServPolicyMapElementIndex OBJECT-TYPE SYNTAX Integer32(1..512) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in this table." ::= { diffServPolicyMapElementEntry 1 } diffServPolicyMapElementClassMapIndex OBJECT-TYPE SYNTAX Integer32(1..512) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the class map binding to this entry. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex." ::= { diffServPolicyMapElementEntry 2 } diffServPolicyMapElementMeterIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the meter binding to this entry. The meter identified by a particular value of this index is associated with the same diffServMeterEntry as identified by the same value of diffServMeterIndex. If this value is zero, no associated meter will be associated, as zero is not a valid meter index." ::= { diffServPolicyMapElementEntry 3 } diffServPolicyMapElementActionIndex OBJECT-TYPE SYNTAX Integer32(1..512) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the action binding to this entry. The action identified by a particular value of this index is associated with the same diffServActionEntry as identified by the same value of diffServActionIndex." ::= { diffServPolicyMapElementEntry 4 } diffServPolicyMapElementStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServPolicyMapElementEntry 5 } diffServClassMapTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServClassMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for class map." ::= { diffServMgt 13 } diffServClassMapEntry OBJECT-TYPE SYNTAX DiffServClassMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for class map." INDEX { diffServClassMapIndex } ::= { diffServClassMapTable 1 } DiffServClassMapEntry ::= SEQUENCE { diffServClassMapIndex Integer32, diffServClassMapName DisplayString, diffServClassMapDescription DisplayString, diffServClassMapMatchType INTEGER, diffServClassMapElementIndexTypeList OCTET STRING, diffServClassMapElementIndexList OCTET STRING, diffServClassMapStatus RowStatus } diffServClassMapIndex OBJECT-TYPE SYNTAX Integer32(1..512) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in this table." ::= { diffServClassMapEntry 1 } diffServClassMapName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this entry." ::= { diffServClassMapEntry 2 } diffServClassMapDescription OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The description of this entry." ::= { diffServClassMapEntry 3 } diffServClassMapMatchType OBJECT-TYPE SYNTAX INTEGER { matchAny(1), matchAll(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The map match type of this entry." ::= { diffServClassMapEntry 4 } diffServClassMapElementIndexTypeList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string containes the type of class map element indexes. Two octets which are represented in network order express one type of the class map element index in network order and it maps the index of differServClasssMapElementIndexList in order. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry. When the type is ipv6Ace(4), the maping index of differServClasssMapElementIndexList is the diffServIpv6AceEntry." ::= { diffServClassMapEntry 5 } diffServClassMapElementIndexList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string containes the class map element indexes. Two octets express one index and it is represented in network order. This index list indicates the particular class map elements which belong to this table. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is two octet specified in differServClasssMapElementIndexTypeList in order. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry. When type is ipv6Ace(4), the maping index of differServClasssMapElementIndexList is the diffServIpv6AceEntry." ::= { diffServClassMapEntry 6 } diffServClassMapStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServClassMapEntry 7 } diffServClassMapAttachCtl OBJECT IDENTIFIER ::= { diffServMgt 14 } diffServClassMapAttachCtlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index for attachment control. Specifies the class map as the target to relate with class map elements. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex." ::= { diffServClassMapAttachCtl 1 } diffServClassMapAttachCtlElementIndexType OBJECT-TYPE SYNTAX INTEGER { macAce(1), ipAce(2), acl(3), ipv6Ace(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Element Index for attachment control. Specifies the type of class map element to relate with the class map. When type is macAce(1), the index of diffServClassMapAttachCtlElementIndex is the index of diffServMacAceEntry. When the type is ipAce(2), the index of diffServClassMapAttachCtlElementIndex is the index of diffServIpAceEntry. When the type is acl(3), the index of diffServClassMapAttachCtlElementIndex is the index of diffServAclEntry. When type is ipv6Ace(4), the index of diffServClassMapAttachCtlElementIndex is the index of diffServIpv6AceEntry." ::= { diffServClassMapAttachCtl 2 } diffServClassMapAttachCtlElementIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Element Index for attachment control. Specifies the class map element related with the class map. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is specified in diffServClassMapAttachCtlElementIndexType. When the type is macAce(1), the maping index of differServClasssMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of differServClasssMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of differServClasssMapElementIndexList is the diffServAclEntry. When type is ipv6Ace(4), the maping index of differServClasssMapElementIndexList is the diffServIpv6AceEntry." ::= { diffServClassMapAttachCtl 3 } diffServClassMapAttachCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), attach(2), detach(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular class map element is attached to a particular class map. When setting this object to detach(3) to begin the not attached operation, then a particular class map element is not attached to a particular class map. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1). The value of a particular class map is specified in the AclAttachCtlTargetIndex. The class map element is specified by diffServClassMapAttachCtlElementIndexType and diffServClassMapAttachCtlElementIndex." ::= { diffServClassMapAttachCtl 4 } diffServAclTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for ACL." ::= { diffServMgt 15 } diffServAclEntry OBJECT-TYPE SYNTAX DiffServAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for ACL." INDEX { diffServAclIndex } ::= { diffServAclTable 1 } DiffServAclEntry ::= SEQUENCE { diffServAclIndex Integer32, diffServAclName DisplayString, diffServAclType INTEGER, diffServAclAceIndexList OCTET STRING, diffServAclStatus RowStatus } diffServAclIndex OBJECT-TYPE SYNTAX Integer32(1..64) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the ACL table." ::= { diffServAclEntry 1 } diffServAclName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of this entry." ::= { diffServAclEntry 2 } diffServAclType OBJECT-TYPE SYNTAX INTEGER { mac(1), ipstandard(2), ipextended(3), ipv6standard(4), ipv6extended(5), arp(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of this entry. When the value of ACL type is modified, then the ACEs in the diffServAclAceIndexList of this entry will be auto-removed, and this entry will be auto- unbound from the diffServPortTable and the diffServClassMapTable." ::= { diffServAclEntry 3 } diffServAclAceIndexList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string containes the ACE indexes. Two octets express one index and it is represented in network order. This index list indicates the particular ACEs which belong to this table. The ACE uses type to indicate the diffServMacAceEntry, the diffServIpAceEntry, the diffServIpv6AceEntry or the diffServArpAceEntry. The type is specified in diffServAclType. When the type is mac(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipstandard(2) or ipextended(3), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6standard(4) or ipv6extended(5), the index of diffServAclAceIndexList is the diffServIpv6AceEntry. When the type is arp(6), the index of diffServAclAceIndexList is the diffServArpAceEntry." ::= { diffServAclEntry 4 } diffServAclStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServAclEntry 5 } diffServAclAttachCtl OBJECT IDENTIFIER ::= { diffServMgt 16 } diffServAclAttachCtlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index for attachment control. Specifies the ACL as the target to relate with the IP ACE, the MAC ACE or IPv6 ACE. The ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex." ::= { diffServAclAttachCtl 1 } diffServAclAttachCtlAceType OBJECT-TYPE SYNTAX INTEGER { macAce(1), ipAce(2), ipv6Ace(3), arpAce(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type for attachment control. Specifies the type of diffServAclAttachCtlAceIndex to relate with the diffServAclAttachCtlIndex. When the type is macAce(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipAce(2), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6Ace(3), the index of diffServAclAceIndexList is the diffServIpv6AceEntry. When the type is arpAce(4), the index of diffServAclAceIndexList is the diffServArpAceEntry." ::= { diffServAclAttachCtl 2 } diffServAclAttachCtlAceIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index for attachment control. Specifies the ACE to relate with the diffServAclAttachCtlIndex. When diffServAclAttachCtlAceType is macAce(1), the value of diffServAclAttachCtlIndex is the diffServMacAceEntry. When diffServAclAttachCtlAceType is ipAce(2), the value of diffServAclAttachCtlIndex is the diffServIpAceEntry. When diffServAclAttachCtlAceType is ipv6Ace(3), the value of diffServAclAttachCtlIndex is the diffServIpv6AceEntry. When diffServAclAttachCtlAceType is arpAce(4), the value of diffServAclAttachCtlIndex is the diffServArpAceEntry." ::= { diffServAclAttachCtl 3 } diffServAclAttachCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), attach(2), detach(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular ACE is attached to a particular ACL. When setting this object to detach(3) to begin the not attached operation, then a particular ACE is not attached to a particular ACL. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1), The value of a particular ACL is specified in the diffServAclAttachCtlAceType and diffServAclAttachCtlAceIndex." ::= { diffServAclAttachCtl 4 } diffServIpAceTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServIpAceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for IP ACE." ::= { diffServMgt 17 } diffServIpAceEntry OBJECT-TYPE SYNTAX DiffServIpAceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for IP ACE." INDEX { diffServIpAceIndex } ::= { diffServIpAceTable 1 } DiffServIpAceEntry ::= SEQUENCE { diffServIpAceIndex Integer32, diffServIpAceType INTEGER, diffServIpAceAccess INTEGER, diffServIpAceSourceIpAddr IpAddress, diffServIpAceSourceIpAddrBitmask IpAddress, diffServIpAceDestIpAddr IpAddress, diffServIpAceDestIpAddrBitmask IpAddress, diffServIpAceProtocol Integer32, diffServIpAcePrec Integer32, diffServIpAceTos Integer32, diffServIpAceDscp Integer32, diffServIpAceSourcePortOp INTEGER, diffServIpAceMinSourcePort Integer32, diffServIpAceSourcePortBitmask Integer32, diffServIpAceDestPortOp INTEGER, diffServIpAceMinDestPort Integer32, diffServIpAceDestPortBitmask Integer32, diffServIpAceControlCode Integer32, diffServIpAceControlCodeBitmask Integer32, diffServIpAceStatus RowStatus } diffServIpAceIndex OBJECT-TYPE SYNTAX Integer32(1..512) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the IP ACE table." ::= { diffServIpAceEntry 1 } diffServIpAceType OBJECT-TYPE SYNTAX INTEGER { standard(1), extended(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The specified IP ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0." ::= { diffServIpAceEntry 2 } diffServIpAceAccess OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the action to be taken if a packet matches this ACE." ::= { diffServIpAceEntry 3 } diffServIpAceSourceIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified source IP address. The packet's source address is AND-ed with the value of IpAceSourceIpAddrBitmask and then compared against the value of this object." ::= { diffServIpAceEntry 4 } diffServIpAceSourceIpAddrBitmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified source IP address mask. The packet's source address is AND-ed with the value of IpAceSourceIpAddr and then compared against the value of this object." ::= { diffServIpAceEntry 5 } diffServIpAceDestIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified destination IP address. The packet's destination address is AND-ed with the value of diffServIpAceDestIpAddrBitmask and then compared against the value of this object. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 6 } diffServIpAceDestIpAddrBitmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified destination IP address mask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 7 } diffServIpAceProtocol OBJECT-TYPE SYNTAX Integer32 (0..256) MAX-ACCESS read-create STATUS current DESCRIPTION "The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value of 0 matches every IP packet. The object=256 means 'any'. For example: 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 8 } diffServIpAcePrec OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the IP precedence value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 8. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 9 } diffServIpAceTos OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the IP ToS facility value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 9. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 10 } diffServIpAceDscp OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the DSCP value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 64. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 11 } diffServIpAceSourcePortOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2), range(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means no comparison is to be made with the source TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinSourcePort to match against. range(3),which is used the diffServIpAceMinSourcePort and the diffServIpAceMaxSourcePort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 12 } diffServIpAceMinSourcePort OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServIpAceSourcePortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 13 } diffServIpAceSourcePortBitmask OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServIpAceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpAceMinSourcePort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 15 } diffServIpAceDestPortOp OBJECT-TYPE SYNTAX INTEGER{ noOperator(1), equal(2), range(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinDestPort to match against. range(3),which is used the diffServIpAceMinDestPort and the diffServIpAceMaxDestPort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 16 } diffServIpAceMinDestPort OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServIpAceDestPortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 17 } diffServIpAceDestPortBitmask OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServIpAceDestPortOp is equal(2), this indicates the bitmask of the diffServIpAceMinDestPort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 19 } diffServIpAceControlCode OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how the control flags of TCP packets are to be compared. diffServIpAceControlCode is AND-ed with diffServIpAceControlCodeBitmask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 20 } diffServIpAceControlCodeBitmask OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how the control flags of TCP packets are to be compared. It can be used to check multiple flags of the FIN, SYN, RST, PSH, ACK, URG by the sum of FIN=1, SYN=2, RST=4, PSH=8, ACK=16, URG=32. This object may not be modified if the associated diffServIpAceType object is equal to standard(1)." ::= { diffServIpAceEntry 21 } diffServIpAceStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServIpAceEntry 22 } diffServMacAceTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServMacAceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for MAC ACE." ::= { diffServMgt 18 } diffServMacAceEntry OBJECT-TYPE SYNTAX DiffServMacAceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for MAC ACE." INDEX { diffServMacAceIndex } ::= { diffServMacAceTable 1 } DiffServMacAceEntry ::= SEQUENCE { diffServMacAceIndex Integer32, diffServMacAceAccess INTEGER, diffServMacAcePktformat INTEGER, diffServMacAceSourceMacAddr MacAddress, diffServMacAceSourceMacAddrBitmask MacAddress, diffServMacAceDestMacAddr MacAddress, diffServMacAceDestMacAddrBitmask MacAddress, diffServMacAceVidOp INTEGER, diffServMacAceMinVid Integer32, diffServMacAceVidBitmask Integer32, diffServMacAceEtherTypeOp INTEGER, diffServMacAceEtherTypeBitmask Integer32, diffServMacAceMinEtherType Integer32, diffServMacAceCosOp INTEGER, diffServMacAceCosBitmask Integer32, diffServMacAceMinCos Integer32, diffServMacAceSourceIpAddr IpAddress, diffServMacAceSourceIpAddrBitmask IpAddress, diffServMacAceDestIpAddr IpAddress, diffServMacAceDestIpAddrBitmask IpAddress, diffServMacAceSourceIpv6Addr OCTET STRING, diffServMacAceSourceIpv6AddrPrefixLen Integer32, diffServMacAceDestIpv6Addr OCTET STRING, diffServMacAceDestIpv6AddrPrefixLen Integer32, diffServMacAceIpProtocol Integer32, diffServMacAceL4SourcePortOp INTEGER, diffServMacAceL4SourcePort Integer32, diffServMacAceL4SourcePortBitmask Integer32, diffServMacAceL4DestPortOp INTEGER, diffServMacAceL4DestPort Integer32, diffServMacAceL4DestPortBitmask Integer32, diffServMacAceStatus RowStatus } diffServMacAceIndex OBJECT-TYPE SYNTAX Integer32(1..512) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the MAC ACE table." ::= { diffServMacAceEntry 1 } diffServMacAceAccess OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the action to be taken if a packet matches this ACE." ::= { diffServMacAceEntry 2 } diffServMacAcePktformat OBJECT-TYPE SYNTAX INTEGER { any(1), untagged-Eth2(2), untagged802Dot3(3), tagggedEth2(4), tagged802Dot3(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Used to check the packet format of the packets. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1)." ::= { diffServMacAceEntry 3 } diffServMacAceSourceMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the 48-bit source MAC address. The specified source MAC of the packet. The packet's source MAC address is AND-ed with the value of diffServMacAceSourceMacAddrBitmask and then compared against the value of this object." ::= { diffServMacAceEntry 4 } diffServMacAceSourceMacAddrBitmask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified source MAC address mask." ::= { diffServMacAceEntry 5 } diffServMacAceDestMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND-ed with the value of diffServMacAceDestMacAddrBitmask and then compared against the value of this object." ::= { diffServMacAceEntry 6 } diffServMacAceDestMacAddrBitmask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified destination MAC address mask." ::= { diffServMacAceEntry 7 } diffServMacAceVidOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2), range(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's VID is to be compared. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1)." ::= { diffServMacAceEntry 8 } diffServMacAceMinVid OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the lower bound of the VID value range if the diffServMacAceVidOp is range(3)." ::= { diffServMacAceEntry 9 } diffServMacAceVidBitmask OBJECT-TYPE SYNTAX Integer32 (0..'0FFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "The bit mask of the VID. The default value is 0." DEFVAL { 0 } ::= { diffServMacAceEntry 10 } diffServMacAceEtherTypeOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2), range(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's ether type is to be compared." ::= { diffServMacAceEntry 12 } diffServMacAceEtherTypeBitmask OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "The bit mask of Ether type. The default value is 0." DEFVAL { 0 } ::= { diffServMacAceEntry 13 } diffServMacAceMinEtherType OBJECT-TYPE SYNTAX Integer32 ('0000'h..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the lower bound of the ether type value range if the diffServMacAceEtherTypeOp is range(3)." ::= { diffServMacAceEntry 14 } diffServMacAceStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServMacAceEntry 16 } diffServMacAceCosOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2), range(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's CoS is compared. If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing, and diffServMacAceCosBitmask is used as the bitmask of the CoS value. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos should be used as the lower bound of the CoS value." ::= { diffServMacAceEntry 17 } diffServMacAceCosBitmask OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the bitmask of the CoS value if the object type of diffServMacAceCosOp is equal(2). The default value is 0." ::= { diffServMacAceEntry 18 } diffServMacAceMinCos OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos indicates the lower bound of the CoS value." ::= { diffServMacAceEntry 19 } diffServMacAceSourceIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '0800'h, this specified source IP address. The packet's source address is AND-ed with the value of diffServMacAceSourceIpAddrBitmask and then compared against the value of this object." ::= { diffServMacAceEntry 32 } diffServMacAceSourceIpAddrBitmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '0800'h, this specified source IP address mask. The packet's source address is AND-ed with the value of diffServMacAceSourceIpAddr and then compared against the value of this object." ::= { diffServMacAceEntry 33 } diffServMacAceDestIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '0800'h, this specified destination IP address. The packet's destination address is AND-ed with the value of diffServMacAceDestIpAddrBitmask and then compared against the value of this object." ::= { diffServMacAceEntry 34 } diffServMacAceDestIpAddrBitmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '0800'h, this specified destination IP address mask. The packet's source address is AND-ed with the value of diffServMacAceDestIpAddr and then compared against the value of this object." ::= { diffServMacAceEntry 35 } diffServMacAceSourceIpv6Addr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '86DD'h, this specifies the source IPv6 address." ::= { diffServMacAceEntry 36 } diffServMacAceSourceIpv6AddrPrefixLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '86DD'h, this specifies the length (in bits) associated with the source IPv6 address prefix of this entry." ::= { diffServMacAceEntry 37 } diffServMacAceDestIpv6Addr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '86DD'h, this specifies the destination IPv6 address. This object may not be modified if the associated aclIpv6AceType object is equal to standard(1)." ::= { diffServMacAceEntry 38 } diffServMacAceDestIpv6AddrPrefixLen OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServMacAceEtherTypeOp is equal(2), diffServMacAceEtherTypeBitmask is 'FFFF'h, and diffServMacAceMinEtherType is '86DD'h, this specifies the length (in bits) associated with the destination IPv6 address prefix of this entry." ::= { diffServMacAceEntry 39 } diffServMacAceIpProtocol OBJECT-TYPE SYNTAX Integer32 (0..256) MAX-ACCESS read-create STATUS current DESCRIPTION "The protocol number field in the IP header (or the next header field in the IPv6 header) used to indicate the higher layer protocol as specified in RFC 1700. A value of 0 matches every IP packet. The object=256 means 'any'. For example: 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP. This object may not be modified if the associated diffServMacAceMinEtherType object is not equal to '0800'h or '86DD'h. " ::= { diffServMacAceEntry 40 } diffServMacAceL4SourcePortOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2), range(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's L4 source port is compared." ::= { diffServMacAceEntry 41 } diffServMacAceL4SourcePort OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the object type of diffServMacAceL4SourcePortOp is equal(2), this indicates the l4 source port value for comparing." ::= { diffServMacAceEntry 42 } diffServMacAceL4SourcePortBitmask OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the object type of diffServMacAceL4SourcePortOp is equal(2), this indicates the bitmask for diffServMacAceL4SourcePort" ::= { diffServMacAceEntry 43 } diffServMacAceL4DestPortOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2), range(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's L4 destination port is compared." ::= { diffServMacAceEntry 44 } diffServMacAceL4DestPort OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the object type of diffServMacAceL4DestPortOp is equal(2), this indicates the l4 destination port value for comparing." ::= { diffServMacAceEntry 45 } diffServMacAceL4DestPortBitmask OBJECT-TYPE SYNTAX Integer32 (0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the object type of diffServMacAceL4SourcePortOp is equal(2), this indicates the bitmask for diffServMacAceL4DestPort" ::= { diffServMacAceEntry 46 } diffServActionTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServActionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for action." ::= { diffServMgt 19 } diffServActionEntry OBJECT-TYPE SYNTAX DiffServActionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for action." INDEX { diffServActionIndex } ::= { diffServActionTable 1 } DiffServActionEntry ::= SEQUENCE { diffServActionIndex Integer32, diffServActionList BITS, diffServActionPktNewPri Integer32, diffServActionPktNewPhb Integer32, diffServActionGreenPktTransmit EnabledStatus, diffServActionGreenPktNewDscp Integer32, diffServActionYellowPktNewDscp Integer32, diffServActionYellowPktDrop EnabledStatus, diffServActionRedPktNewDscp Integer32, diffServActionRedPktDrop EnabledStatus, diffServActionStatus RowStatus, diffServActionPktNewIpPrec Integer32, diffServActionPktNewDscp Integer32 } diffServActionIndex OBJECT-TYPE SYNTAX Integer32(1..512) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the action table." ::= { diffServActionEntry 1 } diffServActionList OBJECT-TYPE SYNTAX BITS { actionPktNewPri(0), reserved1(1), actionGreenPktNewDscp(2), actionGreenPktTransmit(3), actionYellowPktNewDscp(4), actionYellowPktDrop(5), actionRedPktNewDscp(6), actionRedPktDrop(7), reserved8(8), actionPktNewPhb(9), actionPktNewIpPrec(10), actionPktNewDscp(11) } MAX-ACCESS read-create STATUS current DESCRIPTION "The bitmap value used to identify which action capabilities are enabled on the entry. The actionPktNewPri and actionPktNewDscp can not be enabled at the same time on the entry. The actionRedPktNewDscp and actionRedDrop can not be enabled at the same time on the entry." ::= { diffServActionEntry 2 } diffServActionPktNewPri OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the new priority value for the packet when the action is satisfied. If the actionPktNewPri bit of the diffServActionList is not enabled, this object can not be set." ::= { diffServActionEntry 3 } diffServActionPktNewPhb OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the inner priority value for the packet when the action is satisfied. If the actionPktNewPhb bit of the diffServActionList is not enabled, this object can not be set." ::= { diffServActionEntry 4 } diffServActionGreenPktTransmit OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The actionGreenPktTransmit bit of the diffServActionList is for configuring this object. If the value of this object is enabled, the green marking packet will be Transmitted." ::= { diffServActionEntry 5 } diffServActionGreenPktNewDscp OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the new DSCP value for the packet when the action is satisfied. The value of this object is ignored whenever the value of diffServActionGreenPktNewDscp object is 64. If the actionGreenPktNewDscp bit of the diffServActionList is not enabled, this object can not be set." ::= { diffServActionEntry 6 } diffServActionYellowPktNewDscp OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the new DSCP value for the packet when the action is satisfied. The value of this object is ignored whenever the value of diffServActionYellowPktNewDscp object is 64. If the actionYellowPktNewDscp bit of the diffServActionList is not enabled, this object can not be set." ::= { diffServActionEntry 7 } diffServActionYellowPktDrop OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The actionYellowPktDrop bit of the diffServActionList is for configuring this object. If the value of this object is enabled, the red marking packet will be dropped." ::= { diffServActionEntry 8 } diffServActionRedPktNewDscp OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the new DSCP value for the red marking packet when the action is satisfied. The value of this object is ignored whenever the value of diffServActionRedPktNewDscp object is 64. If the actionRedPktNewDscp bit of the diffServActionList is not enabled, this object can not be set." ::= { diffServActionEntry 9 } diffServActionRedPktDrop OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The actionRedPktDrop bit of the diffServActionList is for configuring this object. If the value of this object is enabled, the red marking packet will be dropped." ::= { diffServActionEntry 10 } diffServActionStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row, modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServActionEntry 11 } diffServActionPktNewIpPrec OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the new precedence value for the packet when the action is satisfied. If the actionPktNewIpPrec bit of the diffServActionList is not enabled, this object can not be set." ::= { diffServActionEntry 12 } diffServActionPktNewDscp OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the new DSCP value for the packet when the action is satisfied. If the actionPktNewDscp bit of the diffServActionList is not enabled, this object can not be set." ::= { diffServActionEntry 13 } diffServMeterTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServMeterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for meter." ::= { diffServMgt 20 } diffServMeterEntry OBJECT-TYPE SYNTAX DiffServMeterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for meter." INDEX { diffServActionIndex } ::= { diffServMeterTable 1 } DiffServMeterEntry ::= SEQUENCE { diffServMeterIndex Integer32, diffServMeterModel INTEGER, diffServMeterRate Integer32, diffServMeterBurstSize Integer32, diffServMeterStatus RowStatus, diffServMeterPeakRate Integer32, diffServMeterPeakBurstSize Integer32 } diffServMeterIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry that describes a single set of token bucket parameters." ::= { diffServMeterEntry 1 } diffServMeterModel OBJECT-TYPE SYNTAX INTEGER { default(0), flow(1), trTcmColorBlind(2), trTcmColorAware(3), srTcmColorBlind(6), srTcmColorAware(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Metering algorithm associated with the Token Bucket parameters. The zeroDotZero indicates this is unknown." ::= { diffServMeterEntry 2 } diffServMeterRate OBJECT-TYPE SYNTAX Integer32 (0|1..1000000) MAX-ACCESS read-create STATUS current DESCRIPTION "The token-bucket rate, in kilobits per second (kbps)." ::= { diffServMeterEntry 3 } diffServMeterBurstSize OBJECT-TYPE SYNTAX Integer32 (0|1..16000000) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of bytes in a single transmission burst." ::= { diffServMeterEntry 4 } diffServMeterStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServMeterEntry 6 } diffServMeterPeakRate OBJECT-TYPE SYNTAX Integer32 (0|1..1000000) MAX-ACCESS read-create STATUS current DESCRIPTION "The token-bucket rate, in kilobits per second (kbps)." ::= { diffServMeterEntry 7 } diffServMeterPeakBurstSize OBJECT-TYPE SYNTAX Integer32 (0|1..16000000) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of bytes in a double transmission burst." ::= { diffServMeterEntry 8 } diffServIpv6AceTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServIpv6AceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for IPv6 ACE." ::= { diffServMgt 21 } diffServIpv6AceEntry OBJECT-TYPE SYNTAX DiffServIpv6AceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry fo IPv6 ACE." INDEX { diffServIpv6AceIndex } ::= { diffServIpv6AceTable 1 } DiffServIpv6AceEntry ::= SEQUENCE { diffServIpv6AceIndex Integer32, diffServIpv6AceType INTEGER, diffServIpv6AceAccess INTEGER, diffServIpv6AceSourceIpAddr OCTET STRING, diffServIpv6AceSourceIpAddrPrefixLen Integer32, diffServIpv6AceDestIpAddr OCTET STRING, diffServIpv6AceDestIpAddrPrefixLen Integer32, diffServIpv6AceDscp Integer32, diffServIpv6AceStatus RowStatus, diffServIpv6AceSourcePortOp INTEGER, diffServIpv6AceSourcePort Integer32, diffServIpv6AceSourcePortBitmask Integer32, diffServIpv6AceDestPortOp INTEGER, diffServIpv6AceDestPort Integer32, diffServIpv6AceDestPortBitmask Integer32 } diffServIpv6AceIndex OBJECT-TYPE SYNTAX Integer32 (1..2048) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the IPv6 table." ::= { diffServIpv6AceEntry 1 } diffServIpv6AceType OBJECT-TYPE SYNTAX INTEGER { standard(1), extended(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The specified IP v6 ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0." ::= { diffServIpv6AceEntry 2 } diffServIpv6AceAccess OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the action to be taken if a packet matches this ACE." ::= { diffServIpv6AceEntry 3 } diffServIpv6AceSourceIpAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the source IPv6 address." ::= { diffServIpv6AceEntry 4 } diffServIpv6AceSourceIpAddrPrefixLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The length (in bits) associated with the source IPv6 address prefix of this entry." ::= { diffServIpv6AceEntry 5 } diffServIpv6AceDestIpAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the destination IPv6 address. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1)." ::= { diffServIpv6AceEntry 6 } diffServIpv6AceDestIpAddrPrefixLen OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-create STATUS current DESCRIPTION "The length (in bits) associated with the destination IPv6 address prefix of this entry. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1)." ::= { diffServIpv6AceEntry 7 } diffServIpv6AceDscp OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the DSCP value to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1)." ::= { diffServIpv6AceEntry 9 } diffServIpv6AceStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServIpv6AceEntry 11 } diffServIpv6AceSourcePortOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the source TCP/UDP port number. equal(2), which uses the diffServIpv6AceSourcePort and diffServIpv6AceSourcePortBitmask to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1)." ::= { diffServIpv6AceEntry 13 } diffServIpv6AceSourcePort OBJECT-TYPE SYNTAX Integer32(0..'FFFF'h) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the diffServIpv6AceSourcePortOp is equal(2), this indicates the TCP/UDP port number value." ::= { diffServIpv6AceEntry 14 } diffServIpv6AceSourcePortBitmask OBJECT-TYPE SYNTAX Integer32(0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServIpv6AceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpv6AceSourcePort." ::= { diffServIpv6AceEntry 15 } diffServIpv6AceDestPortOp OBJECT-TYPE SYNTAX INTEGER { noOperator(1), equal(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. equal(2), which uses the diffServIpv6AceDestPort and diffServIpv6AceDestPortBitmask to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1)." ::= { diffServIpv6AceEntry 16 } diffServIpv6AceDestPort OBJECT-TYPE SYNTAX Integer32(0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServIpv6AceDestPortOp is equal(2), this indicates the TCP/UDP port number value." ::= { diffServIpv6AceEntry 17 } diffServIpv6AceDestPortBitmask OBJECT-TYPE SYNTAX Integer32(0..'FFFF'h) MAX-ACCESS read-create STATUS current DESCRIPTION "If the diffServIpv6AceDestPortOp is equal(2), this indicates the bitmask of the diffServIpv6AceDestPort." ::= { diffServIpv6AceEntry 18 } diffServArpAceTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServArpAceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of all of diffServArpAceEntry." ::= { diffServMgt 23 } diffServArpAceEntry OBJECT-TYPE SYNTAX DiffServArpAceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for diffServArpAceTable." INDEX { diffServArpAceIndex } ::= { diffServArpAceTable 1 } DiffServArpAceEntry ::= SEQUENCE { diffServArpAceIndex Integer32, diffServArpAceAction INTEGER, diffServArpAcePktType INTEGER, diffServArpAceSourceIpAddr IpAddress, diffServArpAceSourceIpAddrBitmask IpAddress, diffServArpAceDestIpAddr IpAddress, diffServArpAceDestIpAddrBitmask IpAddress, diffServArpAceSourceMacAddr OCTET STRING, diffServArpAceSourceMacAddrBitmask OCTET STRING, diffServArpAceDestMacAddr OCTET STRING, diffServArpAceDestMacAddrBitmask OCTET STRING, diffServArpAceLogStatus EnabledStatus, diffServArpAceStatus RowStatus } diffServArpAceIndex OBJECT-TYPE SYNTAX Integer32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The unique index of an ACE within an ACL." ::= { diffServArpAceEntry 1 } diffServArpAceAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the action to be taken if a packet matches this ACE. This object cannot not be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 2 } diffServArpAcePktType OBJECT-TYPE SYNTAX INTEGER { request(1), response(2), both(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the packet type to be taken if a packet matches this ACE. This object can not be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 3 } diffServArpAceSourceIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified source ARP address. The packet's source address is AND'ed with the value of diffServArpAceSourceIpAddrBitmask and then compared against the value of this object. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 4 } diffServArpAceSourceIpAddrBitmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified source ARP address mask. The packet's destination address is AND'ed with the value of diffServArpAceSourceIpAddr and then compared against the value of this object." ::= { diffServArpAceEntry 5 } diffServArpAceDestIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified destination IP address. The packet's destination address is AND'ed with the value of diffServArpAceDestIpAddrBitmask and then compared against the value of this object." ::= { diffServArpAceEntry 6 } diffServArpAceDestIpAddrBitmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The specified destination IP address mask." ::= { diffServArpAceEntry 7 } diffServArpAceSourceMacAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the 48-bit destination MAC address. The specified source MAC of the packet. The packet's source MAC address is AND'ed with the value of aceArpSourceMacAddrBitmask and then compared against the value of this object. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 8 } diffServArpAceSourceMacAddrBitmask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) MAX-ACCESS read-create STATUS current DESCRIPTION "The specified source MAC address mask. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 9 } diffServArpAceDestMacAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND'ed with the value of aceArpDestMacAddrBitmask and then compared against the value of this object. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 10 } diffServArpAceDestMacAddrBitmask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) MAX-ACCESS read-create STATUS current DESCRIPTION "The specified destination MAC address mask. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 11 } diffServArpAceLogStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether to log messages against the packets. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1)." ::= { diffServArpAceEntry 12 } diffServArpAceStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB." ::= { diffServArpAceEntry 13 } diffServArpTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of all of diffServArpEntry." ::= { diffServMgt 24 } diffServArpEntry OBJECT-TYPE SYNTAX DiffServArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for diffServArpTable." INDEX { diffServArpAclName } ::= { diffServArpTable 1 } DiffServArpEntry ::= SEQUENCE { diffServArpAclName DisplayString } diffServArpAclName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of an ACL. Within a feature, a unique name is used to identify the list to which the entry belongs in the device." ::= { diffServArpEntry 1 } diffServTcamMgt OBJECT IDENTIFIER ::= { diffServMgt 25 } diffServTcamTotalPolicyControlEntries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of policy control entries." ::= { diffServTcamMgt 1 } diffServTcamFreePolicyControlEntries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The free number of policy control entries." ::= { diffServTcamMgt 2 } diffServTcamUtilization OBJECT-TYPE SYNTAX Integer32(0..10000) MAX-ACCESS read-only STATUS current DESCRIPTION "TCAM utilization in hundredths of a percent." ::= { diffServTcamMgt 3 } diffServTcamEntriesUsedBySystem OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of policy control entries used by system." ::= { diffServTcamMgt 4 } diffServTcamEntriesUsedByUser OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of policy control entries used by user." ::= { diffServTcamMgt 5 } diffServAclHwCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServAclHwCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for differentiated services hardware counter on each port." ::= { diffServMgt 26 } diffServAclHwCounterEntry OBJECT-TYPE SYNTAX DiffServAclHwCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for differentiated services hardware counter on each port." INDEX { diffServAclHwCounterIfIndex, diffServAclHwCounterDirection, diffServAclHwCounterAclIndex, diffServAclHwCounterAceIndex } ::= { diffServAclHwCounterTable 1 } DiffServAclHwCounterEntry ::= SEQUENCE { diffServAclHwCounterIfIndex InterfaceIndex, diffServAclHwCounterDirection INTEGER, diffServAclHwCounterAclIndex Integer32, diffServAclHwCounterAceIndex Integer32, diffServAclHwCounterAceHitCount Unsigned32 } diffServAclHwCounterIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the interface index of diffServPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { diffServAclHwCounterEntry 1 } diffServAclHwCounterDirection OBJECT-TYPE SYNTAX INTEGER { ingress(1), egress(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates a particular direction of traffic." ::= { diffServAclHwCounterEntry 2 } diffServAclHwCounterAclIndex OBJECT-TYPE SYNTAX Integer32 (0|1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the ACL table." ::= { diffServAclHwCounterEntry 3 } diffServAclHwCounterAceIndex OBJECT-TYPE SYNTAX Integer32 (0|1..2048) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry of an ACL. This entry might be a compressed ACE (which index is bigger than SYS_ADPT_MAX_NBRS_OF_ACE_OF_SYSTEM) with multiple user configured ACEs, and the index of compressed ACE will not show in ACE table." ::= { diffServAclHwCounterEntry 4 } diffServAclHwCounterAceHitCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the hardware counter of an ACE entry." ::= { diffServAclHwCounterEntry 5 } -- -- diffServPolicyMapPortTable -- diffServPolicyMapPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServPolicyMapPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for policy map of each port." ::= { diffServMgt 27 } diffServPolicyMapPortEntry OBJECT-TYPE SYNTAX DiffServPolicyMapPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for diffServPolicyMapPortTable." INDEX { diffServPolicyMapPortIfIndex, diffServPolicyMapPortDirection } ::= { diffServPolicyMapPortTable 1 } DiffServPolicyMapPortEntry ::= SEQUENCE { diffServPolicyMapPortIfIndex InterfaceIndex, diffServPolicyMapPortDirection INTEGER, diffServPolicyMapPortPolicyMapIndex Integer32, diffServPolicyMapPortStatus RowStatus } diffServPolicyMapPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is the interface index of DiffServPolicyMapPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { diffServPolicyMapPortEntry 1 } diffServPolicyMapPortDirection OBJECT-TYPE SYNTAX INTEGER { ingress(1), egress(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates this policy map effect to which direction of traffic." ::= { diffServPolicyMapPortEntry 2 } diffServPolicyMapPortPolicyMapIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the policy map index binded to the interface. The policy map identified by a particular value of this index is associated with the same DiffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex." ::= { diffServPolicyMapPortEntry 3 } diffServPolicyMapPortStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB. " ::= { diffServPolicyMapPortEntry 4 } -- -- diffServAccessGroupTable -- diffServAccessGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF DiffServAccessGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for specifies access group for ACL on each port." ::= { diffServMgt 28 } diffServAccessGroupEntry OBJECT-TYPE SYNTAX DiffServAccessGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for diffServAccessGroupTable." INDEX { diffServAccessGroupIfIndex, diffServAccessGroupDirection, diffServAccessGroupType } ::= { diffServAccessGroupTable 1 } DiffServAccessGroupEntry ::= SEQUENCE { diffServAccessGroupIfIndex InterfaceIndex, diffServAccessGroupDirection INTEGER, diffServAccessGroupType INTEGER, diffServAccessGroupAclIndex Integer32, diffServAccessGroupTimeRangeName DisplayString, diffServAccessGroupCounterStatus EnabledStatus, diffServAccessGroupStatus RowStatus } diffServAccessGroupIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is the interface index of diffServAccessGroupEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB. If support global ACL, using the specific ifindex(65535)." ::= { diffServAccessGroupEntry 1 } diffServAccessGroupDirection OBJECT-TYPE SYNTAX INTEGER { ingress(1), egress(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates this access group effect on which direction of traffic." ::= { diffServAccessGroupEntry 2 } diffServAccessGroupType OBJECT-TYPE SYNTAX INTEGER { mac(1), ip(2), ipv6(3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the access group type, only supports binding one ACL on a port." ::= { diffServAccessGroupEntry 3 } diffServAccessGroupAclIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the ACL index applied to this access group. The index uniquely identifies an entry in diffServAclTable." ::= { diffServAccessGroupEntry 4 } diffServAccessGroupTimeRangeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the time range entry bound to the access group. This object should be equal to one of the timeRangeName objects in timeRangeTable." ::= { diffServAccessGroupEntry 5 } diffServAccessGroupCounterStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The acl counter enable status of this access group." ::= { diffServAccessGroupEntry 6 } diffServAccessGroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB. " ::= { diffServAccessGroupEntry 7 } -- -- securityMgt -- -- Management for security, e.g. user security and port security. privateVlanMgt OBJECT IDENTIFIER ::= { securityMgt 1 } portSecurityMgt OBJECT IDENTIFIER ::= { securityMgt 2 } radiusMgt OBJECT IDENTIFIER ::= { securityMgt 4 } tacacsMgt OBJECT IDENTIFIER ::= { securityMgt 5 } sshMgt OBJECT IDENTIFIER ::= { securityMgt 6 } aclMgt OBJECT IDENTIFIER ::= { securityMgt 7 } ipFilterMgt OBJECT IDENTIFIER ::= { securityMgt 9 } userAuthMgt OBJECT IDENTIFIER ::= { securityMgt 10 } dot1xMgt OBJECT IDENTIFIER ::= { securityMgt 11 } aaaMgt OBJECT IDENTIFIER ::= { securityMgt 12 } networkAccessMgt OBJECT IDENTIFIER ::= { securityMgt 13 } macAuthMgt OBJECT IDENTIFIER ::= { securityMgt 14 } webAuthMgt OBJECT IDENTIFIER ::= { securityMgt 15 } dosMgt OBJECT IDENTIFIER ::= { securityMgt 16 } appFilterMgt OBJECT IDENTIFIER ::= { securityMgt 17 } -- -- SYS_CPNT_COMMUNITY_PRIVATE_VLAN (use PVLAN_MGR API) start privateVlanStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This controls whether private VLAN is enabled." ::= { privateVlanMgt 1 } privateVlanUplinkPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This is the list of uplink ports for private VLAN. They should not overlap with privateVlanDownlinkPorts. 0 will be displayed if the privateVlanStatus is disabled. You must enable the privateVlanStatus before setting this variable." ::= { privateVlanMgt 2 } privateVlanDownlinkPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This is the list of downlink ports for private VLAN. They should not overlap with privateVlanUplinkPorts. Multiple port setting is permitted. 0 will be displayed if the privateVlanStatus is disabled. You must enable the privateVlanStatus before setting this variable." ::= { privateVlanMgt 3 } privateVlanVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing private VLAN information on the VLANs which currently exist." ::= { privateVlanMgt 4 } privateVlanVlanEntry OBJECT-TYPE SYNTAX PrivateVlanVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the private VLAN information on the VLANs for a particular management domain." INDEX { privateVlanVlanIndex } ::= { privateVlanVlanTable 1 } PrivateVlanVlanEntry ::= SEQUENCE { privateVlanVlanIndex Integer32, privateVlanVlanType INTEGER, privateVlanAssoicatedPrimaryVlan Integer32 } privateVlanVlanIndex OBJECT-TYPE SYNTAX Integer32(1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID of this private VLAN." ::= { privateVlanVlanEntry 1 } privateVlanVlanType OBJECT-TYPE SYNTAX INTEGER { invalid(1), primary(2), isolated(3), community(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN type as defined for Private VLAN feature. Set the value to invalid(1) to destroy an entry. Set other values to create an entry. If an index already exists, set others to modifiy it. Note that a VLAN's private VLAN type cannot be changed once it has any port members." ::= { privateVlanVlanEntry 2 } privateVlanAssoicatedPrimaryVlan OBJECT-TYPE SYNTAX Integer32(0..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN ID of the associated primary VLAN used for the private VLAN feature if privateVlanVlanType has the value of isolated(3), community(4). If privateVlanVlanType has the value of primary(2), then this object has the value of 0. Note that one isolated VLAN can only be associated with one unique primary VLAN. One primary VLAN can only be associated with one isolated VLAN. One primary VLAN can be associated with multiple community VLANs; one community VLAN can only be associated with one unique primary VLAN." ::= { privateVlanVlanEntry 3 } -- -- Table for configuring secondary VLAN on private ports -- privateVlanPrivatePortTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanPrivatePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information on the configuration of secondary VLANs on the device ports." ::= { privateVlanMgt 5 } privateVlanPrivatePortEntry OBJECT-TYPE SYNTAX PrivateVlanPrivatePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing information of the configuration of secondary VLANs for each port. An entry is created by the managed system for each interface which can be configured as a private port for Private VLAN feature." INDEX { privateVlanPrivatePortIfIndex } ::= { privateVlanPrivatePortTable 1 } PrivateVlanPrivatePortEntry ::= SEQUENCE { privateVlanPrivatePortIfIndex InterfaceIndex, privateVlanPrivatePortSecondaryVlan Integer32 } privateVlanPrivatePortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as the ifIndex." ::= { privateVlanPrivatePortEntry 1 } privateVlanPrivatePortSecondaryVlan OBJECT-TYPE SYNTAX Integer32(0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN ID of the secondary VLAN configured on this private port. A private port is a port that allows ingress traffic of the secondary VLAN as well as egress traffic of its associated primary VLAN, but blocks the egress traffic of the isolated VLAN while allowing the egress traffic of the community or twoWayCommunity VLAN depending on the type of the secondary VLAN. Note that a port can join a secondary VLAN only after this secondary VLAN has been associated with a primary VLAN, i.e., the cpvlanVlanAssociatedPrimaryVlan has a non-zero value. The default value of 0 for this object means this port has not yet joined a secondary VLAN." DEFVAL { 0 } ::= { privateVlanPrivatePortEntry 2 } -- -- Table for remapping secondary VLAN to primary VLAN on promiscuous -- ports for Private VLAN feature -- privateVlanPromPortTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanPromPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing secondary VLAN to primary VLAN remapping information on ports of the device." ::= { privateVlanMgt 6 } privateVlanPromPortEntry OBJECT-TYPE SYNTAX PrivateVlanPromPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing secondary VLAN to primary VLAN remapping information for each port. An entry is created by the managed system for each interface which can be configured as a promiscuous port for the private VLAN feature." INDEX { privateVlanPromPortIfIndex } ::= { privateVlanPromPortTable 1 } PrivateVlanPromPortEntry ::= SEQUENCE { privateVlanPromPortIfIndex InterfaceIndex, privateVlanPromPortPrimaryVlanId Integer32, privateVlanPromPortSecondaryRemap OCTET STRING, privateVlanPromPortSecondaryRemap2k OCTET STRING, privateVlanPromPortSecondaryRemap3k OCTET STRING, privateVlanPromPortSecondaryRemap4k OCTET STRING } privateVlanPromPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as ifIndex." ::= { privateVlanPromPortEntry 1 } privateVlanPromPortPrimaryVlanId OBJECT-TYPE SYNTAX Integer32(0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "The primary VLAN ID of the promiscous port." ::= { privateVlanPromPortEntry 2 } privateVlanPromPortSecondaryRemap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs." ::= { privateVlanPromPortEntry 3 } privateVlanPromPortSecondaryRemap2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 1024 through 2047 in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated on devices which support the range of VlanIndexOrZero up to 4095." ::= { privateVlanPromPortEntry 4 } privateVlanPromPortSecondaryRemap3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 2048 through 3071 in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated on devices which support the range of VlanIndexOrZero up to 4095." ::= { privateVlanPromPortEntry 5 } privateVlanPromPortSecondaryRemap4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANs with VlanIndexOrZero values of 3072 through 4095 in the management domain on this port. The first octet corresponds to VLANs with VlanIndexOrZero values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndexOrZero in that octet. Note that if the length of this string is less than 128 octets, any 'missing' octets are assumed to contain the value zero. An NMS may omit any zero-valued octets from the end of this string in order to reduce SetPDU size, and the agent may also omit zero-valued trailing octets, to reduce the size of GetResponse PDUs. This object is only instantiated on devices which support the range of VlanIndexOrZero up to 4095." ::= { privateVlanPromPortEntry 6 } -- SYS_CPNT_COMMUNITY_PRIVATE_VLAN (use PVLAN_MGR API) end privateVlanSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the settings for private VLAN Session." ::= { privateVlanMgt 8 } privateVlanSessionEntry OBJECT-TYPE SYNTAX PrivateVlanSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the privateVlanSession table." INDEX { privateVlanSessionId } ::= { privateVlanSessionTable 1 } PrivateVlanSessionEntry::= SEQUENCE { privateVlanSessionId INTEGER, privateVlanSessionUplinkPorts PortList, privateVlanSessionDownlinkPorts PortList, privateVlanSessionStatus ValidStatus } privateVlanSessionId OBJECT-TYPE SYNTAX INTEGER(1..4) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The session ID that may specifiy certain entry in the table which contains private VLAN session information." ::= { privateVlanSessionEntry 1 } privateVlanSessionUplinkPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "This is the list of uplink ports for a session of private VLAN. They should not overlap with the privateVlanSessionPortDownlink of the same session, and they also should not overlap with the privateVlanSessionPortUplink and the privateVlanSessionPortDownlink of other session." ::= { privateVlanSessionEntry 2 } privateVlanSessionDownlinkPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "This is the list of downlink ports for a session of private VLAN. They should not overlap with the privateVlanSessionPortUplink of the same session, and they also should not overlap with the privateVlanSessionPortUplink and the privateVlanSessionPortDownlink of other session." ::= { privateVlanSessionEntry 3 } privateVlanSessionStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this to valid(1) to create an entry. Sets this to invalid(2) to destroy an entry." ::= { privateVlanSessionEntry 4 } privateVlanUplinkToUplink OBJECT-TYPE SYNTAX INTEGER { blocking(1), forwarding(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets this to blocking(2) to deny the traffic of uplink ports between different sessions. Set this to forwarding(1) to allow the traffic of uplink ports between different sessions." ::= { privateVlanMgt 9 } portSecPortTable OBJECT-TYPE SYNTAX SEQUENCE OF PortSecPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port security(MAC binding) Table." ::= { portSecurityMgt 1 } portSecPortEntry OBJECT-TYPE SYNTAX PortSecPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of portSecPortTable." INDEX { portSecPortIndex } ::= { portSecPortTable 1 } PortSecPortEntry ::= SEQUENCE { portSecPortIndex InterfaceIndex, portSecPortStatus EnabledStatus, portSecAction INTEGER, portSecMaxMacCount Integer32 } portSecPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { portSecPortEntry 1 } portSecPortStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable port security and set disabled(2) to disable port security." ::= { portSecPortEntry 2 } portSecAction OBJECT-TYPE SYNTAX INTEGER { none(1), trap(2), shutdown(3), trapAndShutdown(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The corresponding actions that will take place when a port is under intrusion, when this variable is set to none(1), no action will be performed, when this variable is set to trap(2), a swPortSecurityTrap trap will be sent, when this variable is set to shutdown(3), the port will shutdown, when this variable is set to trapAndShutdown(4), a swPortSecurityTrap will be sent and the port will shutdown." ::= { portSecPortEntry 3 } portSecMaxMacCount OBJECT-TYPE SYNTAX Integer32(0..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximun number of MAC addresses that will be learned and locked. When we change the value of this variable, if the portSecPortStatus is enabled, we will discard all secure MAC and begin to learn again, until the number of MAC has reached this value, and only the secure MAC addresses can enter this port. If the portSecPortStatus is disabled, we will begin to learn the MAC, and auto enabled the portSecPortStatus when the MAC has reached this value." ::= { portSecPortEntry 4 } -- -- portSecMacAsPermanentMgt -- portSecMacAsPermanentMgt OBJECT IDENTIFIER ::= { portSecurityMgt 6 } portSecMacAsPermanentPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB. Specifies the interface to convert the learnt secured MAC address into manual configured. '0' represents that no interface is specified." ::= { portSecMacAsPermanentMgt 1 } portSecMacAsPermanentAction OBJECT-TYPE SYNTAX INTEGER { noAction (1), action (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set action(2) to convert the learnt secured MAC address into manual configured. When action finsh or no action, the value of this object is noAction(1)." ::= { portSecMacAsPermanentMgt 2 } -- -- radiusMgt -- -- Management for Remote Authentication Dial-In User Service (RADIUS). --SYS_ADPT_MAX_NBR_OF_RADIUS_SERVERS=1: single server --SYS_ADPT_MAX_NBR_OF_RADIUS_SERVERS>1: multiple server radiusServerGlobalAuthPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Aauthentication port number for RADIUS server. When specified radius server do not set aauthentication port number, this value is used." ::= { radiusMgt 1 } radiusServerGlobalAcctPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Accounting port number of RADIUS server. When specified radius server do not set accounting port number, this value is used." ::= { radiusMgt 2 } radiusServerGlobalKey OBJECT-TYPE SYNTAX DisplayString(SIZE(0..48)) MAX-ACCESS read-write STATUS current DESCRIPTION "Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string. When specified radius server do not set key, this this value is used." ::= { radiusMgt 3 } radiusServerGlobalRetransmit OBJECT-TYPE SYNTAX INTEGER (1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of retransmissions for RADIUS. When specified radius server do not set maximum number of retransmissions, this value is used." ::= { radiusMgt 4 } radiusServerGlobalTimeout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout for RADIUS. When specified radius server do not set timeout, this value is used." ::= { radiusMgt 5 } --radiusServerTable radiusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF RadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for RADIUS server." ::= { radiusMgt 7 } radiusServerEntry OBJECT-TYPE SYNTAX RadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for radiusServerTable." INDEX { radiusServerIndex } ::= { radiusServerTable 1 } RadiusServerEntry ::= SEQUENCE { radiusServerIndex Integer32, radiusServerAddress IpAddress, radiusServerAuthPortNumber Integer32, radiusServerAcctPortNumber Integer32, radiusServerKey DisplayString, radiusServerRetransmit Integer32, radiusServerTimeout Integer32, radiusServerStatus ValidStatus } radiusServerIndex OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RADIUS server index in the table." ::= { radiusServerEntry 1 } radiusServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP address of a RADIUS server." ::= { radiusServerEntry 2 } radiusServerAuthPortNumber OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Authentication port number of RADIUS server." ::= { radiusServerEntry 3 } radiusServerAcctPortNumber OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Accounting port number of RADIUS server." ::= { radiusServerEntry 4 } radiusServerKey OBJECT-TYPE SYNTAX DisplayString(SIZE(0..48)) MAX-ACCESS read-write STATUS current DESCRIPTION "Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string." ::= { radiusServerEntry 5 } radiusServerRetransmit OBJECT-TYPE SYNTAX Integer32 (1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout for RADIUS." ::= { radiusServerEntry 6 } radiusServerTimeout OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout for RADIUS." ::= { radiusServerEntry 7 } radiusServerStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { radiusServerEntry 8 } -- -- tacacsMgt -- -- Management for Terminal Access Controller Access Control System plus (TACACS+). -- Global server setting tacacsPlusServerGlobalPortNumber OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "TCP port number of TACACS+ server. When specified TACACS+ server do not set TCP port number, this this value is used." ::= { tacacsMgt 2 } tacacsPlusServerGlobalKey OBJECT-TYPE SYNTAX DisplayString(SIZE(0..48)) MAX-ACCESS read-write STATUS current DESCRIPTION "The encryption key used to encrpt the traffic between client and TACACS+ server. Do not use blank spaces in the string. This variable can only be set. When this variable is read, it always returns a zero-length string.When specified TACACS+ server do not set the encryption key , this this value is used." ::= { tacacsMgt 3 } tacacsPlusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF TacacsPlusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for TACACS+ server." ::= { tacacsMgt 4 } tacacsPlusServerEntry OBJECT-TYPE SYNTAX TacacsPlusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for tacacsPlusServerTable." INDEX { tacacsPlusServerIndex } ::= { tacacsPlusServerTable 1 } TacacsPlusServerEntry ::= SEQUENCE { tacacsPlusServerIndex Integer32, tacacsPlusServerAddress IpAddress, tacacsPlusServerPortNumber Integer32, tacacsPlusServerKey DisplayString, tacacsPlusServerStatus ValidStatus } tacacsPlusServerIndex OBJECT-TYPE SYNTAX Integer32 (1..1) MAX-ACCESS not-accessible STATUS current DESCRIPTION "TACACS+ server index." ::= { tacacsPlusServerEntry 1 } tacacsPlusServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP address of a TACACS+ server." ::= { tacacsPlusServerEntry 2 } tacacsPlusServerPortNumber OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "TCP port number of a TACACS+ server." ::= { tacacsPlusServerEntry 3 } tacacsPlusServerKey OBJECT-TYPE SYNTAX DisplayString(SIZE(0..48)) MAX-ACCESS read-create STATUS current DESCRIPTION "The encryption key used to encrpt the traffic between client and TACACS+ server. Do not use blank spaces in the string. This variable can only be set. When this variable is read, it always returns a zero-length string." ::= { tacacsPlusServerEntry 4 } tacacsPlusServerStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { tacacsPlusServerEntry 8 } -- -- sshMgt -- -- Management for Secure Shell Configuration sshServerStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of Secure Shell Server. Set this value to enabled(1) to enable SSH server, set this value to disabled(2) to disable the SSH server." ::= { sshMgt 1 } sshServerMajorVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The major version of the SSH Server." ::= { sshMgt 2 } sshServerMinorVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minor version of the SSH Server." ::= { sshMgt 3 } sshTimeout OBJECT-TYPE SYNTAX INTEGER(1..120) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The time interval that the router waits for the SSH client to respond. The range is 1-120." ::= { sshMgt 4 } sshAuthRetries OBJECT-TYPE SYNTAX INTEGER(1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of attempts after which the interface is reset. The range is 1-5." ::= { sshMgt 5 } sshConnInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF SshConnInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for Secure Shell Connection." ::= { sshMgt 6 } sshConnInfoEntry OBJECT-TYPE SYNTAX SshConnInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for sshConnInfoTable." INDEX { sshConnID } ::= { sshConnInfoTable 1 } SshConnInfoEntry ::= SEQUENCE { --both sshv1 & sshv2 start sshConnID Integer32, sshConnMajorVersion Integer32, sshConnMinorVersion Integer32, sshConnStatus INTEGER, --both sshv1 & sshv2 end --both sshv1 & sshv2 start sshConnUserName DisplayString, sshDisconnect INTEGER, --both sshv1 & sshv2 end --sshv2 only start sshConnEncryptionTypeStr DisplayString --sshv2 only end } --both sshv1 & sshv2 start sshConnID OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The connection ID of the Secure Shell Connection." ::= { sshConnInfoEntry 1 } sshConnMajorVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The SSH major version." ::= { sshConnInfoEntry 2 } sshConnMinorVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The SSH minor version." ::= { sshConnInfoEntry 3 } sshConnStatus OBJECT-TYPE SYNTAX INTEGER { negotiationStart(1), authenticationStart(2), sessionStart(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The SSH connection State. negotiationStart(1) means the SSH is in its negotiation start state, authenticationStart(2) means the SSH is in authentication start state, sessionStart(3) means the SSH is in session start State." ::= { sshConnInfoEntry 5 } --both sshv1 & sshv2 end --both sshv1 & sshv2 start sshConnUserName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The user name of the connection." ::= { sshConnInfoEntry 6 } sshDisconnect OBJECT-TYPE SYNTAX INTEGER { noDisconnect(1), disconnect(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set the variable to disconnect the connection, noDisconnect(1) will always be obtained when reading this variable." ::= { sshConnInfoEntry 7 } --both sshv1 & sshv2 end --sshv2 only start sshConnEncryptionTypeStr OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption type of the SSH." ::= { sshConnInfoEntry 8 } sshKeySize OBJECT-TYPE SYNTAX INTEGER(512..896) MAX-ACCESS read-write STATUS current DESCRIPTION "The SSH server key size." ::= { sshMgt 7 } sshRsaHostKey1 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 1." ::= { sshMgt 8 } sshRsaHostKey2 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 2." ::= { sshMgt 9 } sshRsaHostKey3 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 3." ::= { sshMgt 10 } sshRsaHostKey4 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 4." ::= { sshMgt 11 } sshRsaHostKey5 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 5." ::= { sshMgt 12 } sshRsaHostKey6 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 6." ::= { sshMgt 13 } sshRsaHostKey7 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 7." ::= { sshMgt 14 } sshRsaHostKey8 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA host key segment 8." ::= { sshMgt 15 } sshDsaHostKey1 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 1." ::= { sshMgt 16 } sshDsaHostKey2 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 2." ::= { sshMgt 17 } sshDsaHostKey3 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 3." ::= { sshMgt 18 } sshDsaHostKey4 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 4." ::= { sshMgt 19 } sshDsaHostKey5 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 5." ::= { sshMgt 20 } sshDsaHostKey6 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 6." ::= { sshMgt 21 } sshDsaHostKey7 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 7." ::= { sshMgt 22 } sshDsaHostKey8 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA host key segment 8." ::= { sshMgt 23 } sshHostKeyGenAction OBJECT-TYPE SYNTAX INTEGER { noGen(1), genRsaKey(2), genDsaKey(3), genBothKeys(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is for host key generating. For the set behavior: Set it to genRsaKey(2) to generate the RSA host key, and to genDsaKey(3) to generate the DSA host key, if genBothKeys(4) is set, both RSA and DSA host key are generated. For the get behavior: You will get genRsaKey(2), genDsaKey(3) or genBothKeys(4) when the key gen action is in progress. otherwise, you will get noGen(1)." ::= { sshMgt 24 } sshHostKeyGenStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), success(2), failure(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of the last KeyGen status. if no key gen action has been performed. you will get unknown(1) status." ::= { sshMgt 25 } sshHostKeySaveAction OBJECT-TYPE SYNTAX INTEGER { noSave(1), save(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To save host key from memory to flash. For the set behavior: Set it to save(2) to perform the save operation. For the get behavior: You will get save(1) when the save action is in progress. Otherwise, you will get noSave(1)." ::= { sshMgt 26 } sshHostKeySaveStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), success(2), failure(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of the last savekey status. If no save action has been performed, you will get unknown(1) status." ::= { sshMgt 27 } sshHostKeyDelAction OBJECT-TYPE SYNTAX INTEGER { noDel(1), delRsaKey(2), delDsaKey(3), delBothKeys(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "To delete the host key. For the set behavior: Set it to delRsaKey(2) to delete the RSA host key, to delDsaKey(3) to delete the DSA host key, or to delBothKeys(4) to delete both RSA and DSA host key. For the get behavior: You will get delRsaKey(2), delDsaKey(3) or delBothKeys(4) when the delete operation is in progress. Otherwise, you will get noDel(1)." ::= { sshMgt 28 } sshUserTable OBJECT-TYPE SYNTAX SEQUENCE OF SshUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of all of sshUserEntry." ::= { sshMgt 29 } sshUserEntry OBJECT-TYPE SYNTAX SshUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for sshUserTable." INDEX { IMPLIED sshUserName} ::= { sshUserTable 1 } SshUserEntry ::= SEQUENCE { sshUserName DisplayString, sshUserRsaKey1 KeySegment, sshUserRsaKey2 KeySegment, sshUserRsaKey3 KeySegment, sshUserRsaKey4 KeySegment, sshUserRsaKey5 KeySegment, sshUserRsaKey6 KeySegment, sshUserRsaKey7 KeySegment, sshUserRsaKey8 KeySegment, sshUserDsaKey1 KeySegment, sshUserDsaKey2 KeySegment, sshUserDsaKey3 KeySegment, sshUserDsaKey4 KeySegment, sshUserDsaKey5 KeySegment, sshUserDsaKey6 KeySegment, sshUserDsaKey7 KeySegment, sshUserDsaKey8 KeySegment, sshUserKeyDelAction INTEGER } sshUserName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Name." ::= { sshUserEntry 1 } sshUserRsaKey1 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 1." ::= { sshUserEntry 2 } sshUserRsaKey2 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 2." ::= { sshUserEntry 3 } sshUserRsaKey3 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 3." ::= { sshUserEntry 4 } sshUserRsaKey4 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 4." ::= { sshUserEntry 5 } sshUserRsaKey5 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 5." ::= { sshUserEntry 6 } sshUserRsaKey6 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 6." ::= { sshUserEntry 7 } sshUserRsaKey7 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 7." ::= { sshUserEntry 8 } sshUserRsaKey8 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The RSA user key segment 8." ::= { sshUserEntry 9 } sshUserDsaKey1 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 1." ::= { sshUserEntry 10 } sshUserDsaKey2 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 2." ::= { sshUserEntry 11 } sshUserDsaKey3 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 3." ::= { sshUserEntry 12 } sshUserDsaKey4 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 4." ::= { sshUserEntry 13 } sshUserDsaKey5 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 5." ::= { sshUserEntry 14 } sshUserDsaKey6 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 6." ::= { sshUserEntry 15 } sshUserDsaKey7 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 7." ::= { sshUserEntry 16 } sshUserDsaKey8 OBJECT-TYPE SYNTAX KeySegment MAX-ACCESS read-only STATUS current DESCRIPTION "The DSA user key segment 8." ::= { sshUserEntry 17 } sshUserKeyDelAction OBJECT-TYPE SYNTAX INTEGER { noDel(1), delRsaKey(2), delDsaKey(3), delBothKeys(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "To delete the user key. For the set behavior: Set it to delRsaKey(2) to delete the RSA user key, to delDsaKey(3) to delete the DSA user key, or to delBothKeys(4) to delete both RSA and DSA user key. For the get behavior: You will get delRsaKey(2), delDsaKey(3) or delBothKeys(4) when the delete operation is in progress. Otherwise, you will get noDel(1)." ::= { sshUserEntry 18 } sshRsaHostKeySHA1FingerPrint OBJECT-TYPE SYNTAX DisplayString(SIZE(65)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SHA1 finger print of the RSA host key." ::= { sshMgt 30 } sshRsaHostKeyMD5FingerPrint OBJECT-TYPE SYNTAX DisplayString(SIZE(47)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MD5 finger print of RSA host key." ::= { sshMgt 31 } sshDsaHostKeySHA1FingerPrint OBJECT-TYPE SYNTAX DisplayString(SIZE(65)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SHA1 finger print of the DSA host key." ::= { sshMgt 32 } sshDsaHostKeyMD5FingerPrint OBJECT-TYPE SYNTAX DisplayString(SIZE(47)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MD5 finger print of the DSA host key." ::= { sshMgt 33 } --sshv2 only end -- -- aaaMgt -- aaaMethodTable OBJECT-TYPE SYNTAX SEQUENCE OF AaaMethodEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the settings needed for accounting." ::= { aaaMgt 1 } aaaMethodEntry OBJECT-TYPE SYNTAX AaaMethodEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the aaaMethodTable." INDEX { aaaMethodIndex } ::= { aaaMethodTable 1 } AaaMethodEntry ::= SEQUENCE { aaaMethodIndex Integer32, aaaMethodName DisplayString, aaaMethodGroupName DisplayString, aaaMethodMode INTEGER, aaaMethodStatus ValidStatus, aaaMethodClientType INTEGER, aaaMethodPrivilegeLevel INTEGER } aaaMethodIndex OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the index for the entry." ::= { aaaMethodEntry 1 } aaaMethodName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Name for the method." ::= { aaaMethodEntry 2 } aaaMethodGroupName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Name for the server to use, pointing to aaaRadiusGroupName or aaaTacacsPlusGroupName." ::= { aaaMethodEntry 3 } aaaMethodMode OBJECT-TYPE SYNTAX INTEGER { start-stop(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "start-stop(1),sends a 'start' accounting notice at the beginning of a process and a 'stop' accounting notice at the end of a process. The 'start' accounting record is sent in the background. The requested user process begins regardless of whether or not the 'start' accounting notice was received by the accounting server." ::= { aaaMethodEntry 4 } aaaMethodStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set to 1 to initiate the aaaMethodTable, 2 to destroy the table." ::= { aaaMethodEntry 5 } aaaMethodClientType OBJECT-TYPE SYNTAX INTEGER { dot1x(1), exec(2), commands(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "dot1x(1): Provides accounting service for 802.1x activity; exec(2): Provides accounting service for EXEC connection such as Telnet, SSH or console; commands(3): Provides accounting service for command privileges." ::= { aaaMethodEntry 6 } aaaMethodPrivilegeLevel OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the privilege level for the entry. When aaaMethodClientType is in the mode of command(3), the privilege level is enabled to be accessed." ::= { aaaMethodEntry 7 } aaaRadiusGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AaaRadiusGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Uses a subset of RADIUS servers for accounting as defined by the server group" ::= { aaaMgt 2 } aaaRadiusGroupEntry OBJECT-TYPE SYNTAX AaaRadiusGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of aaaRadiusGroupEntry." INDEX { aaaRadiusGroupIndex } ::= { aaaRadiusGroupTable 1 } AaaRadiusGroupEntry ::= SEQUENCE { aaaRadiusGroupIndex Integer32, aaaRadiusGroupServerBitMap OCTET STRING, aaaRadiusGroupName DisplayString, aaaRadiusGroupStatus ValidStatus } aaaRadiusGroupIndex OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the index for the entry." ::= { aaaRadiusGroupEntry 1 } aaaRadiusGroupServerBitMap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies which RADIUS sever to use, each bit points to each radius server. 80 (1000 0000) point to radius server 1, C0 (11000000) points to radius 1 and radius 2." ::= { aaaRadiusGroupEntry 2 } aaaRadiusGroupName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Uses a subset of servers for accounting as defined by the server group. The same name as aaaTacasPlusGroupName is not allowed." ::= { aaaRadiusGroupEntry 3 } aaaRadiusGroupStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table." ::= { aaaRadiusGroupEntry 4 } aaaTacacsPlusGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AaaTacacsPlusGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Uses a subset of TACACS+ servers for accounting as defined by the server group" ::= { aaaMgt 3 } aaaTacacsPlusGroupEntry OBJECT-TYPE SYNTAX AaaTacacsPlusGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of aaaTacacsPlusGroupEntry." INDEX { aaaTacacsPlusGroupIndex } ::= { aaaTacacsPlusGroupTable 1 } AaaTacacsPlusGroupEntry ::= SEQUENCE { aaaTacacsPlusGroupIndex Integer32, aaaTacacsPlusGroupServerBitMap OCTET STRING, aaaTacacsPlusGroupName DisplayString, aaaTacacsPlusGroupStatus ValidStatus } aaaTacacsPlusGroupIndex OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the index for the entry." ::= { aaaTacacsPlusGroupEntry 1 } aaaTacacsPlusGroupServerBitMap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies which TACACS+ sever to use." ::= { aaaTacacsPlusGroupEntry 2 } aaaTacacsPlusGroupName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Uses a subset of servers for accounting as defined by the server group. We can't have the same name as aaaRadiusGroupName" ::= { aaaTacacsPlusGroupEntry 3 } aaaTacacsPlusGroupStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table." ::= { aaaTacacsPlusGroupEntry 4 } aaaUpdate OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the periodic interim accounting records to be sent to the accounting server and periodic intervals to send accounting update records(in minutes)." ::= { aaaMgt 4 } aaaAccountTable OBJECT-TYPE SYNTAX SEQUENCE OF AaaAccountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies an interface or a set of interfaces that the accounting method list will be applied to." ::= { aaaMgt 5 } aaaAccountEntry OBJECT-TYPE SYNTAX AaaAccountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of aaaAccountTable." INDEX { aaaAccountIfIndex } ::= { aaaAccountTable 1 } AaaAccountEntry ::= SEQUENCE { aaaAccountIfIndex InterfaceIndex, aaaAccountMethodName DisplayString, aaaAccountProtocol INTEGER, aaaAccountStatus ValidStatus } aaaAccountIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defined as the ifIndex" ::= { aaaAccountEntry 1 } aaaAccountMethodName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the name of the list of accounting methods to use. If no method name is specified, the system uses the default." ::= { aaaAccountEntry 2 } aaaAccountProtocol OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Get the protocol type of a list method to know which server (RADIUS or TACACS+) is in use." ::= { aaaAccountEntry 3 } aaaAccountStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set to 1 to initiate the aaaRadiusGroupTable, 2 to destroy the table." ::= { aaaAccountEntry 4 } aaaCommandPrivilegesTable OBJECT-TYPE SYNTAX SEQUENCE OF AaaCommandPrivilegesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the settings needed for command privileges." ::= { aaaMgt 8 } aaaCommandPrivilegesEntry OBJECT-TYPE SYNTAX AaaCommandPrivilegesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the aaaCommandPrivilegesTable." INDEX { aaaCommandPrivilegesLevel, aaaCommandPrivilegesInterfaceIndex } ::= { aaaCommandPrivilegesTable 1 } AaaCommandPrivilegesEntry ::= SEQUENCE { aaaCommandPrivilegesLevel INTEGER, aaaCommandPrivilegesInterfaceIndex INTEGER, aaaCommandPrivilegesMethodName DisplayString } aaaCommandPrivilegesLevel OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the privilege level index for the entry." ::= { aaaCommandPrivilegesEntry 1 } aaaCommandPrivilegesInterfaceIndex OBJECT-TYPE SYNTAX INTEGER { console(1), vty(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the interface index for the entry." ::= { aaaCommandPrivilegesEntry 2 } aaaCommandPrivilegesMethodName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the method name in the lists under the mode of command privileges." ::= { aaaCommandPrivilegesEntry 3 } aaaAccExecTable OBJECT-TYPE SYNTAX SEQUENCE OF AaaAccExecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies an interface or a set of interfaces that the accounting method list will be applied to." ::= { aaaMgt 9 } aaaAccExecEntry OBJECT-TYPE SYNTAX AaaAccExecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of aaaAccExecTable." INDEX { aaaAccExecIndex } ::= { aaaAccExecTable 1 } AaaAccExecEntry ::= SEQUENCE { aaaAccExecIndex INTEGER, aaaAccExecMethodName DisplayString } aaaAccExecIndex OBJECT-TYPE SYNTAX INTEGER { console(1), vty(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The method of accessing CLI management." ::= { aaaAccExecEntry 1 } aaaAccExecMethodName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the name of the list of accounting methods to use. If no method name is specified, the system uses the default." ::= { aaaAccExecEntry 2 } -- --userAuthMgt -- userAuthEnablePassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set enable password or delete enable password. NULL is used to delete the enable password. The password is starting with alphanumeric." ::= { userAuthMgt 3 } userAuthMethod OBJECT-TYPE SYNTAX INTEGER { local(1), localradius(2), localradiustacacs(3), localtacacs(4), localtacacsradius(5), radius(6), radiuslocal(7), radiuslocaltacacs(8), radiustacacs(9), radiustacacslocal(10), tacacs(11), tacacslocal(12), tacacslocalradius(13), tacacsradius(14), tacacsradiuslocal(15) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set user authencation method for system." ::= { userAuthMgt 4 } userAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF UserAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is for creating the new user." ::= { userAuthMgt 5 } userAuthEntry OBJECT-TYPE SYNTAX UserAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries in this table correspond to the users entries in system." INDEX { userAuthUserName } ::= { userAuthTable 1 } UserAuthEntry ::= SEQUENCE { userAuthUserName DisplayString, userAuthPassword DisplayString, userAuthPrivilege Integer32, userAuthPublicKey DisplayString, userAuthStatus Integer32 } userAuthUserName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The name of the user. The user name is starting with alphanumeric." ::= { userAuthEntry 1 } userAuthPassword OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the user password. zero length input will set the user enrty without password. If the user is not exist, it will create the user with the giving password and privilege 0. The password is starting with alphanumeric." ::= { userAuthEntry 2 } userAuthPrivilege OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the user level. If the user is not exist, it will create the user with the giving privilege with none password. Privilege 15 is maximum privilege that only can be applied to system administrator." ::= { userAuthEntry 3 } userAuthPublicKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "User public key, the value can be 'RSA' or 'DSA' or 'Both' or 'None'." ::= { userAuthEntry 4 } userAuthStatus OBJECT-TYPE SYNTAX Integer32 (0..1) MAX-ACCESS read-create STATUS current DESCRIPTION "This node is used to create the user entry by '1' and to delete one user entry by '0'." ::= { userAuthEntry 5 } aclAttachCtlMgt OBJECT IDENTIFIER ::= { aclMgt 13 } aclAttachCtlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index for attachment control. Specifies the ACL as the target to relate with the IP ACE, the MAC ACE or IPv6 ACE. The ACL identified by a particular value of this index is associated with the same aclEntry as identified by the same value of aclIndex." ::= { aclAttachCtlMgt 1 } aclAttachCtlAceType OBJECT-TYPE SYNTAX INTEGER { noType(0), macAce(1), ipAce(2), ipv6Ace(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type for attachment control. Specifies the type of aclAttachCtlAceIndex to relate with the aclAttachCtlIndex. When the type is macAce(1), the index of aclAceIndexList is the aclMacAceEntry. When the type is ipAce(2), the index of aclAceIndexList is the aclIpAceEntry. When the type is ipv6Ace(3), the index of aclAceIndexList is the aclIpv6AceEntry." ::= { aclAttachCtlMgt 2 } aclAttachCtlAceIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Index for attachment control. Specifies the ACE to relate with the aclAttachCtlIndex. When aclAttachCtlAceType is macAce(1), the value of aclAttachCtlIndex is the diffServMacAceEntry. When aclAttachCtlAceType is ipAce(2), the value of aclAttachCtlIndex is the diffServIpAceEntry. When aclAttachCtlAceType is ipv6Ace(3), the value of aclAttachCtlIndex is the diffServIpv6AceEntry." ::= { aclAttachCtlMgt 3 } aclAttachCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), attach(2), detach(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular ACE is attached to a particular ACL. When setting this object to detach(3) to begin the not attached operation, then a particular ACE is not attached to a particular ACL. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1), The value of a particular ACL is specified in the aclAttachCtlAceType and aclAttachCtlAceIndex." ::= { aclAttachCtlMgt 4 } -- -- ipFilterMgt -- --ipFilterSnmpInetTable ipFilterSnmpInetTable OBJECT-TYPE SYNTAX SEQUENCE OF IpFilterSnmpInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of IP address entries." ::= { ipFilterMgt 12 } ipFilterSnmpInetEntry OBJECT-TYPE SYNTAX IpFilterSnmpInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry includes an IP address range which the system will allow to connect to this device through SNMP." INDEX { ipFilterSnmpInetAddressType, IMPLIED ipFilterSnmpInetAddressStart} ::= { ipFilterSnmpInetTable 1 } IpFilterSnmpInetEntry ::= SEQUENCE { ipFilterSnmpInetAddressType InetAddressType, ipFilterSnmpInetAddressStart InetAddress, ipFilterSnmpInetAddressEnd InetAddress, ipFilterSnmpInetStatus ValidStatus } ipFilterSnmpInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of IP address filter. Only supports IPv4 and IPv6 address types." ::= { ipFilterSnmpInetEntry 1 } ipFilterSnmpInetAddressStart OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The start IP address." ::= { ipFilterSnmpInetEntry 2 } ipFilterSnmpInetAddressEnd OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The end IP address." ::= { ipFilterSnmpInetEntry 3 } ipFilterSnmpInetStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { ipFilterSnmpInetEntry 4 } --ipFilterHttpInetTable ipFilterHttpInetTable OBJECT-TYPE SYNTAX SEQUENCE OF IpFilterHttpInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of IP address entries." ::= { ipFilterMgt 13 } ipFilterHttpInetEntry OBJECT-TYPE SYNTAX IpFilterHttpInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry includes an IP address range which the system will allow to connect to this device through SNMP." INDEX { ipFilterHttpInetAddressType, IMPLIED ipFilterHttpInetAddressStart } ::= { ipFilterHttpInetTable 1 } IpFilterHttpInetEntry ::= SEQUENCE { ipFilterHttpInetAddressType InetAddressType, ipFilterHttpInetAddressStart InetAddress, ipFilterHttpInetAddressEnd InetAddress, ipFilterHttpInetStatus ValidStatus } ipFilterHttpInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of IP address filter . Only supports IPv4 and IPv6 address types." ::= { ipFilterHttpInetEntry 1 } ipFilterHttpInetAddressStart OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The start IP address." ::= { ipFilterHttpInetEntry 2 } ipFilterHttpInetAddressEnd OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The end IP address." ::= { ipFilterHttpInetEntry 3 } ipFilterHttpInetStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { ipFilterHttpInetEntry 4 } --ipFilterTelnetInetTable ipFilterTelnetInetTable OBJECT-TYPE SYNTAX SEQUENCE OF IpFilterTelnetInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of IP address entries." ::= { ipFilterMgt 14 } ipFilterTelnetInetEntry OBJECT-TYPE SYNTAX IpFilterTelnetInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry includes an IP address range which the system will allow them to connect to this device through SNMP." INDEX { ipFilterTelnetInetAddressType, IMPLIED ipFilterTelnetInetAddressStart } ::= { ipFilterTelnetInetTable 1 } IpFilterTelnetInetEntry ::= SEQUENCE { ipFilterTelnetInetAddressType InetAddressType, ipFilterTelnetInetAddressStart InetAddress, ipFilterTelnetInetAddressEnd InetAddress, ipFilterTelnetInetStatus ValidStatus } ipFilterTelnetInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of IP address filter . Only supports IPv4 and IPv6 address types." ::= { ipFilterTelnetInetEntry 1 } ipFilterTelnetInetAddressStart OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The start IP address." ::= { ipFilterTelnetInetEntry 2 } ipFilterTelnetInetAddressEnd OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The end IP address." ::= { ipFilterTelnetInetEntry 3 } ipFilterTelnetInetStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { ipFilterTelnetInetEntry 4 } ipFilterAllClientCtl OBJECT IDENTIFIER ::= { ipFilterMgt 15 } ipFilterAllClientCtlInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of IP address filter. Only supports IPv4 and IPv6 address types." ::= { ipFilterAllClientCtl 1 } ipFilterAllClientCtlInetAddressStart OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The start IP address." ::= { ipFilterAllClientCtl 2 } ipFilterAllClientCtlInetAddressEnd OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The end IP address." ::= { ipFilterAllClientCtl 3 } ipFilterAllClientCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), create(2), destroy(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for IP filter control. Set this object to create(2) to create entries in the ipFilterSnmpInetTable, ipFilterHttpInetTable and ipFilterTelnetInetTable. Set this object to destroy(3) to destroy specified entries in the ipFilterSnmpInetTable, ipFilterHttpInetTable and ipFilterTelnetInetTable. When the action is finshed, whether successfully or not, or no action is taken, the value of this object is always noAction(1)." ::= { ipFilterAllClientCtl 4 } -- -- dot1xMgt -- -- The extension table of dot1xAuthConfigTable dot1xAuthConfigExtTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xAuthConfigExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension table of dot1xAuthConfigTable." ::= { dot1xMgt 1 } dot1xAuthConfigExtEntry OBJECT-TYPE SYNTAX Dot1xAuthConfigExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of dot1xAuthConfigExtTable." AUGMENTS { dot1xAuthConfigEntry } ::= { dot1xAuthConfigExtTable 1 } Dot1xAuthConfigExtEntry ::= SEQUENCE { dot1xAuthConfigExtOperMode INTEGER, dot1xAuthConfigExtMultiHostMaxCnt Integer32, dot1xAuthConfigExtPortIntrusionAction INTEGER } dot1xAuthConfigExtOperMode OBJECT-TYPE SYNTAX INTEGER { singleHost(1), multiHost(2), macBasedAuth(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The operation mode of dot1x port which allows host connection to 802.1x-authorized ports." ::= { dot1xAuthConfigExtEntry 1 } dot1xAuthConfigExtMultiHostMaxCnt OBJECT-TYPE SYNTAX Integer32(1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of hosts when the dot1xAuthConfigExtOperMode is multiHost(2). When the operation Mode is singleHost(1), we can ignore this variables." DEFVAL { 5 } ::= { dot1xAuthConfigExtEntry 2 } dot1xAuthConfigExtPortIntrusionAction OBJECT-TYPE SYNTAX INTEGER { block-traffic(1), guest-vlan(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Responses to intrusion when the authentication is failed; block-traffic(1) means that to block traffic when the authentication is failed and guest-vlan(2) means that to join to a guest VLAN when the authentication is failed." ::= { dot1xAuthConfigExtEntry 3 } dot1xEapolPassThrough OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "When this variable is enabled(1), EAPOL frames will be forwarded to all ports where the Spanning Tree status is forwarding. When this variable is disabled(2), EAPOL frames will be discarded. EAPOL Pass-Through operates when the global status of 802.1X is disabled." DEFVAL { disabled } ::= { dot1xMgt 3 } -- -- networkAccessPortTable -- networkAccessPortTable OBJECT-TYPE SYNTAX SEQUENCE OF NetworkAccessPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the information of network access about every port." ::= { networkAccessMgt 2 } networkAccessPortEntry OBJECT-TYPE SYNTAX NetworkAccessPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the networkAccessPort table." INDEX { networkAccessPortPortIndex } ::= { networkAccessPortTable 1 } NetworkAccessPortEntry ::= SEQUENCE { networkAccessPortPortIndex InterfaceIndex, networkAccessPortDynamicVlan EnabledStatus, networkAccessPortMaxMacCount INTEGER, networkAccessPortMode EnabledStatus, networkAccessPortMacFilter INTEGER, networkAccessPortGuestVlan INTEGER, networkAccessPortLinkDetectionStatus EnabledStatus, networkAccessPortLinkDetectionMode INTEGER, networkAccessPortLinkDetectionAciton INTEGER, networkAccessPortDynamicQos EnabledStatus } networkAccessPortPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this port index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { networkAccessPortEntry 1 } networkAccessPortDynamicVlan OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Sets enabled(1) to enable dynamic VLAN assigment and sets disabled(2) to disable dynamic VLAN assigment." ::= { networkAccessPortEntry 2 } networkAccessPortMaxMacCount OBJECT-TYPE SYNTAX INTEGER (0..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum number of authenticated MAC address." ::= { networkAccessPortEntry 3 } networkAccessPortMode OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the secure port mode. enabled(1) means that Mac address authentication is used and disabled(2) means that the authentication is disabled." ::= { networkAccessPortEntry 4 } networkAccessPortMacFilter OBJECT-TYPE SYNTAX INTEGER (0..64) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the MAC filter ID, Set this variable to zero to disable MAC filter." ::= { networkAccessPortEntry 5 } networkAccessPortGuestVlan OBJECT-TYPE SYNTAX INTEGER (0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the guest VLAN ID. To disable the VLAN, set the value to 0." ::= { networkAccessPortEntry 6 } networkAccessPortLinkDetectionStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to enabled(1) to enable link detection. Set this object to disabled(2) to disable link detection." ::= { networkAccessPortEntry 7 } networkAccessPortLinkDetectionMode OBJECT-TYPE SYNTAX INTEGER { linkUp(1), linkDown(2), linkUpDown(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the detection event for a port. Set this object to linkUp(1) to detect a link-up event. Set this object to linkDown(2) to detect a link-down event. Set this object to linkUpDown(3) to detect both link up and link down events." ::= { networkAccessPortEntry 8 } networkAccessPortLinkDetectionAciton OBJECT-TYPE SYNTAX INTEGER { trap(1), shutDown(2), trapAndShutDown(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to take when a networkAccessPortLinkDetection event is triggered. Set this object to trap(1) to send a trap when a networkAccessPortLinkDetection event is triggered. Set this object to shutDown(2) to shut down the port when a networkAccessPortLinkDetection event is triggered. Set this object to trapAndShutDown(3) to send a trap and shut down the port when a networkAccessPortLinkDetection event is triggered." ::= { networkAccessPortEntry 9 } networkAccessPortDynamicQos OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to enabled(1) to enable Dynamic QoS. Set this object to disabled(2) to disable Dynamic QoS." ::= { networkAccessPortEntry 10 } -- -- networkAccessClearMacAddressMgt -- networkAccessClearMacAddressMgt OBJECT IDENTIFIER ::= { networkAccessMgt 3 } networkAccessClearMacAddressAttribute OBJECT-TYPE SYNTAX INTEGER { all (1), static (2), dynamic (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute for clearing Mac address. Specifies the certain attribute in Mac address table. all(1) indicates both reauthorized and learnt secure MAC address; static(2) indicates reauthorized MAC address; dynamic(3) indicates learnt secure MAC address." ::= { networkAccessClearMacAddressMgt 1 } networkAccessClearMacAddressMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies MAC address in the MAC address table for clearing MAC address. '000000' represents that no MAC address is specified." ::= { networkAccessClearMacAddressMgt 2 } networkAccessClearMacAddressPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The specifies port in the MAC address table for clearing MAC address. '0' represents that no port is specified." ::= { networkAccessClearMacAddressMgt 3 } networkAccessClearMacAddressAction OBJECT-TYPE SYNTAX INTEGER { noclear (1), clear (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for clearing MAC address . When setting this object to clear(2) to begin the clearing MAC address operation, a particular MAC address is cleared from the MAC address table. When the action is finshed whether or not it is successful or no action is taken, the value of this object is always noclear(1)." ::= { networkAccessClearMacAddressMgt 4 } -- -- networkAccessMacAddressTable -- networkAccessMacAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF NetworkAccessMacAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the information of network access MAC addresses." ::= { networkAccessMgt 4} networkAccessMacAddressEntry OBJECT-TYPE SYNTAX NetworkAccessMacAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the networkAccessMacAddress table." INDEX { networkAccessMacAddressAddress, networkAccessMacAddressPort } ::= { networkAccessMacAddressTable 1 } NetworkAccessMacAddressEntry ::= SEQUENCE { networkAccessMacAddressAddress MacAddress, networkAccessMacAddressPort InterfaceIndex, networkAccessMacAddressInetAddressType InetAddressType, networkAccessMacAddressRadiusServerInetAddress InetAddress, networkAccessMacAddressTime DisplayString, networkAccessMacAddressAttribute INTEGER } networkAccessMacAddressAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the authenticated MAC address." ::= { networkAccessMacAddressEntry 1 } networkAccessMacAddressPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the port of authenticated MAC address." ::= { networkAccessMacAddressEntry 2 } networkAccessMacAddressInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of IP address denoted in networkAccessMacAddressRadiusServerInetAddress type." ::= { networkAccessMacAddressEntry 3 } networkAccessMacAddressRadiusServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the IP address of radius server that authenticates the specified Mac address." ::= { networkAccessMacAddressEntry 4 } networkAccessMacAddressTime OBJECT-TYPE SYNTAX DisplayString(SIZE(12)) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the authentication time of the authenticated MAC address. The following form is a text string; 'yyyy MMm DDd HHh MMm SSs'. 'yyyy' is a four-digit year. 'MM' is a month. A single-digit month is preceded by a zero. 'DD' is the day of a month. A single-digit day is preceded by the value zero. 'HH', 'MM' and 'SS' are hour, minute, and second respectively. A single-digit hour, minute, and second are preceded by a zero value. An example is: '2001y 01m 01d 00h 04m 43s'." ::= { networkAccessMacAddressEntry 5 } networkAccessMacAddressAttribute OBJECT-TYPE SYNTAX INTEGER { static (1), dynamic (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the attribute of an authenticated MAC address. static(1) indicates resauthorized secure MAC address. dynamic(2) indicates learnt secure MAC address." ::= { networkAccessMacAddressEntry 6 } networkAccessAging OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to enabled(1) to enable MAC address aging feature. Set this object to disabled(2) to disable MAC address aging feature." ::= { networkAccessMgt 5 } -- -- networkAccessMacFilterWithMaskTable -- networkAccessMacFilterWithMaskTable OBJECT-TYPE SYNTAX SEQUENCE OF NetworkAccessMacFilterWithMaskEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the settings for MAC filter." ::= { networkAccessMgt 6} networkAccessMacFilterWithMaskEntry OBJECT-TYPE SYNTAX NetworkAccessMacFilterWithMaskEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the networkAccessMacFilterWithMaskTable." INDEX { networkAccessMacFilterWithMaskID, networkAccessMacFilterWithMaskMacAddress, networkAccessMacFilterWithMaskMacAddressMask } ::= { networkAccessMacFilterWithMaskTable 1 } NetworkAccessMacFilterWithMaskEntry ::= SEQUENCE { networkAccessMacFilterWithMaskID INTEGER, networkAccessMacFilterWithMaskMacAddress MacAddress, networkAccessMacFilterWithMaskMacAddressMask MacAddress, networkAccessMacFilterWithMaskStatus INTEGER } networkAccessMacFilterWithMaskID OBJECT-TYPE SYNTAX INTEGER (1..64) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the MAC filter ID." ::= { networkAccessMacFilterWithMaskEntry 1 } networkAccessMacFilterWithMaskMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the MAC address to be filtered." ::= { networkAccessMacFilterWithMaskEntry 2 } networkAccessMacFilterWithMaskMacAddressMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the MAC mask to be filtered." ::= { networkAccessMacFilterWithMaskEntry 3 } networkAccessMacFilterWithMaskStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this object to valid(1) to create an entry. Set this object to invalid(2) to destroy an entry." ::= { networkAccessMacFilterWithMaskEntry 4 } macAuthReauthTime OBJECT-TYPE SYNTAX Integer32 (120..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the reauthentication time period." ::= { macAuthMgt 1 } -- -- macAuthPortTable -- macAuthPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MacAuthPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the settings for mac authentication of each port." ::= { macAuthMgt 2 } macAuthPortEntry OBJECT-TYPE SYNTAX MacAuthPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the macAuthPort table." INDEX { macAuthPortIndex } ::= { macAuthPortTable 1 } MacAuthPortEntry ::= SEQUENCE { macAuthPortIndex InterfaceIndex, macAuthPortMaxMacCount INTEGER, macAuthPortIntrusionAction INTEGER } macAuthPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (including trunk members) interface of the port table. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { macAuthPortEntry 1 } macAuthPortMaxMacCount OBJECT-TYPE SYNTAX INTEGER (0..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum number of authenticated MAC addresses for MAC authentication." ::= { macAuthPortEntry 2 } macAuthPortIntrusionAction OBJECT-TYPE SYNTAX INTEGER { block-traffic(1), pass-traffic(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Responses to intrusion when the authentication is failed. block-traffic(1) : denies network access to an unauthorized client; pass-traffic(2) : allows unauthorized clients to the access network." ::= { macAuthPortEntry 3 } webAuthSystemAuthControl OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Sets enabled(1) to enable WebAuth feature and sets disabled(2) to disable WebAuth feature." ::= { webAuthMgt 1 } webAuthSessionTimeout OBJECT-TYPE SYNTAX INTEGER (300..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "For authenticated success users, they can use internet service during a certain period. Whenever this period expires, users need to be re-authenticated again. This period is called session time." ::= { webAuthMgt 5 } webAuthQuietPeriod OBJECT-TYPE SYNTAX INTEGER (1..180) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the re-authentication interval when the authentication fail attempts reach the webAuthLoginAttempts value. Unauthenticated user won't be authenticated during this period." ::= { webAuthMgt 6 } webAuthLoginAttempts OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the counter that configures the authentication fail times for a client. If authentication fail times reaches the specified value, the client are not allowed to login for some period." ::= { webAuthMgt 7 } -- -- webAuthReauthenticateMgt -- webAuthReauthenticateMgt OBJECT IDENTIFIER ::= { webAuthMgt 8 } webAuthReauthenticatePort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the port to re-authenticate for all of its authenticated hosts." ::= { webAuthReauthenticateMgt 1 } webAuthReauthenticateInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies host type to re-authenticate." ::= { webAuthReauthenticateMgt 2 } webAuthReauthenticateInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Specificies host to re-authenticate." ::= { webAuthReauthenticateMgt 3 } webAuthReauthenticateAction OBJECT-TYPE SYNTAX INTEGER { noReauth (1), reauth (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for WebAuth re-authenication. When setting this object to reauth(2) to begin the re-authenticated operation, a particular user is re-authenticated. When the action is finshed whether it is successfully, or no action is taken, the value of this object is always noReauth(1)." ::= { webAuthReauthenticateMgt 4 } -- -- webAuthPortConfigTable -- webAuthPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF WebAuthPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the settings for web authentication of each port." ::= { webAuthMgt 9 } webAuthPortConfigEntry OBJECT-TYPE SYNTAX WebAuthPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the webAuthPortConfigTable." INDEX { webAuthPortConfigPortIndex } ::= { webAuthPortConfigTable 1 } WebAuthPortConfigEntry ::= SEQUENCE { webAuthPortConfigPortIndex InterfaceIndex, webAuthPortConfigStatus INTEGER, webAuthPortConfigAuthenticatedHostCount INTEGER } webAuthPortConfigPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port number of the port that may specify certain entry in the table which contains web authentication information." ::= { webAuthPortConfigEntry 1 } webAuthPortConfigStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Sets enabled(1) to enable web authentication feature for each port and sets disabled(2) to disable web authentication for each port." ::= { webAuthPortConfigEntry 2 } webAuthPortConfigAuthenticatedHostCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the authenticated host counts for each port" ::= { webAuthPortConfigEntry 3 } -- -- webAuthPortInfoTable -- webAuthPortInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF WebAuthPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the information for web authentication of each port." ::= { webAuthMgt 10 } webAuthPortInfoEntry OBJECT-TYPE SYNTAX WebAuthPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the webAuthPortTable." INDEX { webAuthPortInfoPortIndex, webAuthPortInfoPortAuthSuccessIndex} ::= { webAuthPortInfoTable 1 } WebAuthPortInfoEntry ::= SEQUENCE { webAuthPortInfoPortIndex InterfaceIndex, webAuthPortInfoPortAuthSuccessIndex INTEGER, webAuthPortInfoInetAddressType InetAddressType, webAuthPortInfoInetAddress InetAddress, webAuthPortInfoRemainingSessiontime INTEGER, webAuthPortInfoStatus INTEGER } webAuthPortInfoPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port number for which this entry contains web authentication information." ::= { webAuthPortInfoEntry 1 } webAuthPortInfoPortAuthSuccessIndex OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The authentication success number of port for which this entry contains web authentication information." ::= { webAuthPortInfoEntry 2 } webAuthPortInfoInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of IP address denoted in webAuthPortInfoIpAddress type." ::= { webAuthPortInfoEntry 3 } webAuthPortInfoInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address which may specify the entry containing web authentication information." ::= { webAuthPortInfoEntry 4 } webAuthPortInfoRemainingSessiontime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The remaining session time for authenticated hosts. During this period, they may use internet resource. When the session time expires, they will need to re-authenticate again." ::= { webAuthPortInfoEntry 5 } webAuthPortInfoStatus OBJECT-TYPE SYNTAX INTEGER { authenticated (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the web authentication status for each port. authenticated (1) means the user is authenticated." ::= { webAuthPortInfoEntry 6 } -- -- dosMgt -- system OBJECT IDENTIFIER ::= { dosMgt 1 } dosEchoChargen OBJECT IDENTIFIER ::= { system 1 } dosEchoChargenStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of Echo/Chargen protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosEchoChargen 1 } dosEchoChargenRateLimitInKilo OBJECT-TYPE SYNTAX Integer32 (64..2000) MAX-ACCESS read-write STATUS current DESCRIPTION "Value of the rate limit for Echo/Chargen packets. The unit is kilobits per second." ::= { dosEchoChargen 2 } dosSmurf OBJECT IDENTIFIER ::= { system 3 } dosSmurfStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of Smurf protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosSmurf 1 } dosTcpFlooding OBJECT IDENTIFIER ::= { system 4 } dosTcpFloodingStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of TCP flooding protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosTcpFlooding 1 } dosTcpFloodingRateLimitInKilo OBJECT-TYPE SYNTAX Integer32 (64..2000) MAX-ACCESS read-write STATUS current DESCRIPTION "Value of the rate limit for TCP flooding packets. The unit is kilobits per second." ::= { dosTcpFlooding 2 } dosTcpNullScan OBJECT IDENTIFIER ::= { system 5 } dosTcpNullScanStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of TCP Null-scan protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosTcpNullScan 1 } dosTcpSynFinScan OBJECT IDENTIFIER ::= { system 6 } dosTcpSynFinScanStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of TCP SYN FIN scan protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosTcpSynFinScan 1 } dosTcpXmasScan OBJECT IDENTIFIER ::= { system 7 } dosTcpXmasScanStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of TCP Xmas-scan protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosTcpXmasScan 1 } dosUdpFlooding OBJECT IDENTIFIER ::= { system 8 } dosUdpFloodingStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of UDP flooding protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosUdpFlooding 1 } dosUdpFloodingRateLimitInKilo OBJECT-TYPE SYNTAX Integer32 (64..2000) MAX-ACCESS read-write STATUS current DESCRIPTION "Value of the rate limit for UDP flooding packets. The unit is kilobits per second." ::= { dosUdpFlooding 2 } dosWinNuke OBJECT IDENTIFIER ::= { system 9 } dosWinNukeStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of WinNUKE protection. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosWinNuke 1 } dosWinNukeRateLimitInKilo OBJECT-TYPE SYNTAX Integer32 (64..2000) MAX-ACCESS read-write STATUS current DESCRIPTION "Value of the rate limit for WinNUKE packets. The unit is kilobits per second." ::= { dosWinNuke 2 } dosTcpUdpPortZero OBJECT IDENTIFIER ::= { system 11 } dosTcpUdpPortZeroStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of checking for TCP/UDP packets with port 0. Set this to enabled(1) to enable the feature, and set this to disabled(2) to disable the feature." ::= { dosTcpUdpPortZero 1 } -- -- appFilterMgt -- -- Management for application filter to control specific packet transmitted -- status appFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AppFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The application filter Table." ::= { appFilterMgt 1 } appFilterPortEntry OBJECT-TYPE SYNTAX AppFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of appFilterPortTable." INDEX {appFilterPortIndex, appFilterProtocolType} ::= { appFilterPortTable 1 } AppFilterPortEntry ::= SEQUENCE { appFilterPortIndex InterfaceIndex, appFilterProtocolType INTEGER, appFilterPktStatus INTEGER } appFilterPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { appFilterPortEntry 1 } appFilterProtocolType OBJECT-TYPE SYNTAX INTEGER { cdp(1), pvst(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The protocol type define some specific packets which are supported on this function" ::= { appFilterPortEntry 2 } appFilterPktStatus OBJECT-TYPE SYNTAX INTEGER { default(0), discard(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set discard(1) to discard packet and set default(0) to transmit packet in default behavior." ::= { appFilterPortEntry 3 } -- -- layer3Mgt -- -- Management for layer 3 settings and protocols. arpMgt OBJECT IDENTIFIER ::= { layer3Mgt 1 } ripMgt OBJECT IDENTIFIER ::= { layer3Mgt 2 } ospfMgt OBJECT IDENTIFIER ::= { layer3Mgt 3 } routeMgt OBJECT IDENTIFIER ::= { layer3Mgt 5 } -- arpMgt arpCacheDeleteAll OBJECT-TYPE SYNTAX INTEGER { delete(1), noDelete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To delete all dynamic entries in the ARP cache, write this variable to delete(1). Writing this variable to noDelete(2) has no effect on the device. When read, this variable always returns noDelete(2)." ::= { arpMgt 1 } arpCacheTimeout OBJECT-TYPE SYNTAX Integer32(300..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout is provided for entries in the ARP Cache. It is for dynamic mapping only. Static mapping by creating an entry that associates a logical address with a physical address is never aged out." DEFVAL { 1200 } ::= { arpMgt 2 } arpTrafficStatistics OBJECT IDENTIFIER ::= { arpMgt 3 } arpStatSendRequestPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ARP Request packets sent by the ARP process." ::= { arpTrafficStatistics 1 } arpStatRcvRequestPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ARP Request packets received by the ARP process." ::= { arpTrafficStatistics 2 } arpStatSendReplyPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ARP Reply packets sent by the ARP process." ::= { arpTrafficStatistics 3 } arpStatRcvReplyPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ARP Reply packets received by the ARP process." ::= { arpTrafficStatistics 4 } arpProxyArpTable OBJECT-TYPE SYNTAX SEQUENCE OF ArpProxyArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Proxy ARP status. This table has entries for all static VLANs." ::= { arpMgt 4 } arpProxyArpEntry OBJECT-TYPE SYNTAX ArpProxyArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about Proxy ARP configuration." INDEX { arpProxyArpIfIndex } ::= { arpProxyArpTable 1 } ArpProxyArpEntry ::= SEQUENCE { arpProxyArpIfIndex InterfaceIndex, arpProxyArpStatus EnabledStatus } arpProxyArpIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as a VLAN interface. A routing interface is a VLAN that binds an IP subnet." ::= { arpProxyArpEntry 1 } arpProxyArpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable proxy ARP process on an interface." DEFVAL { disabled } ::= { arpProxyArpEntry 2 } -- ripMgt ripBasicTimers OBJECT IDENTIFIER ::= { ripMgt 1 } ripUpdateBasicTimer OBJECT-TYPE SYNTAX Integer32 (5..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The update time in seconds controls the advertising of regular update messages. In the real implementation, the actual timer is this value offset by a random time (+/-50%) each time it is set." DEFVAL { 30 } ::= { ripBasicTimers 1 } ripTimeoutBasicTimer OBJECT-TYPE SYNTAX Integer32 (5..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The timeout timer in seconds governs the validity of a route. It is initialized when a route is established, and any time an update message is received for the route. If the setting time elapses from the last time the timeout was initialized, the route is considered to have expired, and the hop count of the route is set to infinite. It should be at least three times the value of the update timer." DEFVAL { 180 } ::= { ripBasicTimers 2 } ripGarbageCollectionBasicTimer OBJECT-TYPE SYNTAX Integer32 (5..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "When the information about a route becomes invalid, the system does not immediately purge that route from its table. Instead, it continues to advertise the route with an infinite metric. At the same time, the garbage-collection timer is set for that route. When the count reaches zero, the route is purged from the table. This timer allows neighbors to become aware of the invalidity of a route prior to purging." DEFVAL { 120 } ::= { ripBasicTimers 3 } ripRoutingProcessStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable RIP routing process on a system." DEFVAL { disabled } ::= { ripMgt 2 } ripGlobalRouterVersion OBJECT-TYPE SYNTAX INTEGER { rip1(1), rip2(2), byInterface(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "To specify a RIP version used globally by the router. If interface version is configurated, router will use the interface configuration; and if version is not configurated on interface, router will use this global version; and if both interface and global are not configurated, router will use interface's default configuration." DEFVAL { byInterface } ::= { ripMgt 3 } ripInstabilityPreventingTable OBJECT-TYPE SYNTAX SEQUENCE OF RipInstabilityPreventingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of RIP instability preventing status." ::= { ripMgt 4 } ripInstabilityPreventingEntry OBJECT-TYPE SYNTAX RipInstabilityPreventingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about RIP instability preventing configuration. The ifIndex index is a VLAN's ifIndex." INDEX { ripIfindex } ::= { ripInstabilityPreventingTable 1 } RipInstabilityPreventingEntry ::= SEQUENCE { ripIfindex InterfaceIndex, ripSplitHorizonStatus INTEGER } ripIfindex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as a VLAN interface. A routing interface is a VLAN and an IP subnet bound to it." ::= { ripInstabilityPreventingEntry 1 } ripSplitHorizonStatus OBJECT-TYPE SYNTAX INTEGER { splitHorizon(1), poisonReverse(2), none(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable RIP poison reverse on an interface." ::= { ripInstabilityPreventingEntry 2 } ripStatisticsReset OBJECT-TYPE SYNTAX INTEGER { reset(1), noReset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Write it to reset(1), the following objects in RFC 1724 should be reset: 1. Global Counters: 'rip2GlobalRouteChanges', 'rip2GlobalQueries'. 2. Interface Status Table, for each 'rip2IfStatAddress': 'rip2IfStatRcvBadPackets', 'rip2IfStatRcvBadRoutes', 'rip2IfStatSendUpdates' 3. Peer Table, for each 'rip2PeerAddress' and 'rip2PeerDomain', 'rip2PeerRcvBadPackets', 'rip2PeerRcvBadRoutes' When read this value always is noReset(2)." ::= { ripMgt 5 } ripNetwork OBJECT IDENTIFIER ::= { ripMgt 6 } ripNetworkByInetAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RipNetworkByInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP network address table." ::= { ripNetwork 1 } ripNetworkByInetAddrEntry OBJECT-TYPE SYNTAX RipNetworkByInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ripNetworkByInetAddrTable." INDEX { ripNetworkByInetAddrAddressType, ripNetworkByInetAddrAddress, ripNetworkByInetAddrPfxLen } ::= { ripNetworkByInetAddrTable 1 } RipNetworkByInetAddrEntry ::= SEQUENCE { ripNetworkByInetAddrAddressType InetAddressType, ripNetworkByInetAddrAddress InetAddress, ripNetworkByInetAddrPfxLen InetAddressPrefixLength, ripNetworkByInetAddrStatus ValidStatus } ripNetworkByInetAddrAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP Network address type." ::= { ripNetworkByInetAddrEntry 1 } ripNetworkByInetAddrAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP Network address." ::= { ripNetworkByInetAddrEntry 2 } ripNetworkByInetAddrPfxLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "Network prefix length." ::= { ripNetworkByInetAddrEntry 3 } ripNetworkByInetAddrStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this variable to create or destroy a RIP network address." ::= { ripNetworkByInetAddrEntry 4 } ripNetworkByIfindexTable OBJECT-TYPE SYNTAX SEQUENCE OF RipNetworkByIfindexEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIp network ifindex table." ::= { ripNetwork 2 } ripNetworkByIfindexEntry OBJECT-TYPE SYNTAX RipNetworkByIfindexEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ripNetworkByIfindexTable." INDEX { ripNetworkIfindex } ::= { ripNetworkByIfindexTable 1 } RipNetworkByIfindexEntry ::= SEQUENCE { ripNetworkIfindex InterfaceIndex, ripNetworkByIfindexStatus ValidStatus } ripNetworkIfindex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as a layer3 interface." ::= { ripNetworkByIfindexEntry 1 } ripNetworkByIfindexStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this variable to create or destroy a RIP network ifindex table." ::= { ripNetworkByIfindexEntry 2 } ripDistributeListTable OBJECT-TYPE SYNTAX SEQUENCE OF RipDistributeListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP distribute list table. It's used to filter incoming or outgoing route updates using the access-list or prefix-list." ::= { ripMgt 7 } ripDistributeListEntry OBJECT-TYPE SYNTAX RipDistributeListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ripDistributelistTable." INDEX { ripDistributeListInterfaceIndex, ripDistributeListType } ::= { ripDistributeListTable 1 } RipDistributeListEntry ::= SEQUENCE { ripDistributeListInterfaceIndex InterfaceIndex, ripDistributeListType INTEGER, ripDistributeListIncomingRouteFilterName DisplayString, ripDistributeListOutgoingRouteFilterName DisplayString, ripDistributeListStatus ValidStatus } ripDistributeListInterfaceIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the interface on which distribute-list is applied, If index is 0, the filter will be applied to all the interfaces." ::= { ripDistributeListEntry 1 } ripDistributeListType OBJECT-TYPE SYNTAX INTEGER { access-list(1), prefix-list(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Type of distribute-list applied: access-list or prefix-list." ::= { ripDistributeListEntry 2 } ripDistributeListIncomingRouteFilterName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..15)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies access-list or prefix-list name to filter incoming routing updates." ::= { ripDistributeListEntry 3} ripDistributeListOutgoingRouteFilterName OBJECT-TYPE SYNTAX DisplayString(SIZE (1..15)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies access-list or prefix-list name to filter outgoing routing updates." ::= { ripDistributeListEntry 4} ripDistributeListStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this variable to create or destroy a distribute list." ::= { ripDistributeListEntry 5 } ripRedistributeTable OBJECT-TYPE SYNTAX SEQUENCE OF RipRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP Redistribute table. Config rip redistribute type, metric." ::= { ripMgt 8 } ripRedistributeEntry OBJECT-TYPE SYNTAX RipRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ripRedistributeTable." INDEX { ripRedistributeProtocol } ::= { ripRedistributeTable 1 } RipRedistributeEntry ::= SEQUENCE { ripRedistributeProtocol INTEGER, ripRedistributeMetric Integer32, ripRedistributeStatus ValidStatus } ripRedistributeProtocol OBJECT-TYPE SYNTAX INTEGER { connected(1), static(2), ospf(3), bgp(4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Protocol redistributed to Intermediate System: connected -- redistribute from connected routes; static -- redistribute from static routes; ospf -- redistribute from Open Shortest Path First (OSPF); bgp -- redistribute from Border Gateway Protocol (BGP)." ::= { ripRedistributeEntry 1 } ripRedistributeMetric OBJECT-TYPE SYNTAX Integer32(0..16) MAX-ACCESS read-create STATUS current DESCRIPTION "Metric value to be used in redistributing." DEFVAL { 1 } ::= { ripRedistributeEntry 2 } ripRedistributeStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this variable to create or destroy redistribute information." ::= { ripRedistributeEntry 3 } ripDefaultMetric OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS read-write STATUS current DESCRIPTION "A metric for redistribute routes." DEFVAL { 1 } ::= { ripMgt 9 } ripNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF RipNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP neighbor table." ::= { ripMgt 10 } ripNeighborEntry OBJECT-TYPE SYNTAX RipNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ripNeighborTable." INDEX { ripNeighborAddressType, ripNeighborAddress } ::= { ripNeighborTable 1 } RipNeighborEntry ::= SEQUENCE { ripNeighborAddressType InetAddressType, ripNeighborAddress InetAddress, ripNeighborAddressStatus ValidStatus } ripNeighborAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP Neighbor address type." ::= { ripNeighborEntry 1 } ripNeighborAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP Neighbor address." ::= { ripNeighborEntry 2 } ripNeighborAddressStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this variable to create or destroy a RIP neighbor address." ::= { ripNeighborEntry 3 } ripPassiveInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF RipPassiveInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of RIP passive interface status." ::= { ripMgt 11 } ripPassiveInterfaceEntry OBJECT-TYPE SYNTAX RipPassiveInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about RIP passive interface(s) configuration. The index is a VLAN's ifIndex." INDEX { ripInterfaceIndex } ::= { ripPassiveInterfaceTable 1 } RipPassiveInterfaceEntry ::= SEQUENCE { ripInterfaceIndex InterfaceIndex, ripPassiveInterfaceStatus ValidStatus } ripInterfaceIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as a VLAN interface. A passive VLAN interface will suppress route updates on it." ::= { ripPassiveInterfaceEntry 1 } ripPassiveInterfaceStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this variable to create or destroy a RIP passive interface." ::= { ripPassiveInterfaceEntry 2 } ripMaxPrefix OBJECT-TYPE SYNTAX Integer32 (1..11766) MAX-ACCESS read-write STATUS current DESCRIPTION "Max number of RIP dynamic routes." DEFVAL { 11766 } ::= { ripMgt 12 } ripRouteClear OBJECT IDENTIFIER ::= { ripMgt 13 } ripRouteClearByType OBJECT-TYPE SYNTAX INTEGER { noClear(1), all(2), connected(3), ospf(4), rip(5), static(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Write this object value 2-6 to clear rip route by type, when read, this always return noClear(1)." DEFVAL { 1 } ::= { ripRouteClear 1 } ripRouteClearByNetworkTable OBJECT-TYPE SYNTAX SEQUENCE OF RipRouteClearByNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Clear rip route by network address." ::= { ripRouteClear 2 } ripRouteClearByNetworkEntry OBJECT-TYPE SYNTAX RipRouteClearByNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Clear rip route by network address." INDEX { ripRouteClearByNetworkInetAddrType, ripRouteClearByNetworkInetAddr, ripRouteClearByNetworkPfxLen } ::= { ripRouteClearByNetworkTable 1 } RipRouteClearByNetworkEntry ::= SEQUENCE { ripRouteClearByNetworkInetAddrType InetAddressType, ripRouteClearByNetworkInetAddr InetAddress, ripRouteClearByNetworkPfxLen InetAddressPrefixLength, ripRouteClearByNetworkClearAction INTEGER } ripRouteClearByNetworkInetAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP route network address type." ::= { ripRouteClearByNetworkEntry 1 } ripRouteClearByNetworkInetAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP route network address.Write this object to clear rip route by network address." ::= { ripRouteClearByNetworkEntry 2 } ripRouteClearByNetworkPfxLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP route network prefix length." ::= { ripRouteClearByNetworkEntry 3 } ripRouteClearByNetworkClearAction OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Write this object value 2(clear) to clear rip route by spicify network address, when read, this always return noClear(1)." ::= { ripRouteClearByNetworkEntry 4 } ripDefaultInformationOriginate OBJECT-TYPE SYNTAX INTEGER { noOriginate(1), originate(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Write this object value 2(originate) to originate default information, write this object value 1(noOriginate) to not originate default information." DEFVAL { 1 } ::= { ripMgt 14 } ripDistance OBJECT IDENTIFIER ::= { ripMgt 15 } ripDefaultDistance OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Default distance value." DEFVAL { 120 } ::= { ripDistance 1 } ripDistanceTable OBJECT-TYPE SYNTAX SEQUENCE OF RipDistanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Rip distance table" ::= { ripDistance 2 } ripDistanceEntry OBJECT-TYPE SYNTAX RipDistanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Rip distance entry" INDEX { ripDistanceInetAddrType, ripDistanceInetAddr, ripDistancePfxLen } ::= { ripDistanceTable 1 } RipDistanceEntry ::= SEQUENCE { ripDistanceInetAddrType InetAddressType, ripDistanceInetAddr InetAddress, ripDistancePfxLen InetAddressPrefixLength, ripDistanceValue Integer32, ripDistanceAlistName DisplayString, ripDistanceRowStatus RowStatus } ripDistanceInetAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP distace table network address type." ::= { ripDistanceEntry 1 } ripDistanceInetAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP distance table network address." ::= { ripDistanceEntry 2 } ripDistancePfxLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RIP distance table network prefix length." ::= { ripDistanceEntry 3 } ripDistanceValue OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The RIP distance table distance value." ::= { ripDistanceEntry 4 } ripDistanceAlistName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) MAX-ACCESS read-create STATUS current DESCRIPTION "The RIP distance table access list name. If delete the access list name ,set null string" ::= { ripDistanceEntry 5 } ripDistanceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { ripDistanceEntry 6 } -- ospfMgt ospfMultiProcessSystemTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessSystemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptually table for ospfMultiProcessSystemEntry." ::= { ospfMgt 8 } ospfMultiProcessSystemEntry OBJECT-TYPE SYNTAX OspfMultiProcessSystemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptually row for ospfMultiProcessSystemTable." INDEX { ospfMultiProcessProcessId } ::= { ospfMultiProcessSystemTable 1 } OspfMultiProcessSystemEntry ::= SEQUENCE { ospfMultiProcessProcessId Integer32, ospfMultiProcessRouterIdType INTEGER, ospfMultiProcessRfc1583CompatibleState EnabledStatus, ospfMultiProcessAutoCost Integer32, ospfMultiProcessOriginateDefaultRoute EnabledStatus, ospfMultiProcessAdvertiseDefaultRoute INTEGER, ospfMultiProcessExternalMetricType INTEGER, ospfMultiProcessDefaultExternalMetric Integer32, ospfMultiProcessSpfHoldTime Integer32, ospfMultiProcessAreaNumber Integer32, ospfMultiProcessAreaLimit Gauge32, ospfMultiProcessSystemStatus RowStatus, ospfMultiProcessRouterId RouterID, ospfMultiProcessAdminStat Status, ospfMultiProcessVersionNumber INTEGER, ospfMultiProcessAreaBdrRtrStatus TruthValue, ospfMultiProcessASBdrRtrStatus TruthValue, ospfMultiProcessExternLsaCount Gauge32, ospfMultiProcessExternLsaCksumSum Integer32, ospfMultiProcessOriginateNewLsas Counter32, ospfMultiProcessRxNewLsas Counter32, ospfMultiProcessAsLsaCount Integer32, ospfMultiProcessSpfDelayTime Integer32, ospfMultiProcessDefaultMetric Integer32 } ospfMultiProcessProcessId OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Process ID of an OSPF instance. You can create an OSPF instance from 0 to 65535 with its id. 0 is reserved for default process." DEFVAL { 0 } ::= { ospfMultiProcessSystemEntry 1 } ospfMultiProcessRouterIdType OBJECT-TYPE SYNTAX INTEGER { auto(1), manual(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set router ID automatically or manually." DEFVAL { auto } ::= { ospfMultiProcessSystemEntry 2 } ospfMultiProcessRfc1583CompatibleState OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable rfc1583 compatibility." DEFVAL { disabled } ::= { ospfMultiProcessSystemEntry 3 } ospfMultiProcessAutoCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the reference bandwidth of auto cost, the unit is Mbps." DEFVAL { 100 } ::= { ospfMultiProcessSystemEntry 4 } ospfMultiProcessOriginateDefaultRoute OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable ASBR to generate a default external route into an OSPF domain if the default route already exists." DEFVAL { disabled } ::= { ospfMultiProcessSystemEntry 5 } ospfMultiProcessAdvertiseDefaultRoute OBJECT-TYPE SYNTAX INTEGER { always(1), notAlways(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "If 'always', always advertises default route regardless of whether the default route exists. Note that any operation on it will not take effect unless ospfMultiProcessOriginateDefaultRoute has firstly been enabled." DEFVAL { notAlways } ::= { ospfMultiProcessSystemEntry 6 } ospfMultiProcessExternalMetricType OBJECT-TYPE SYNTAX INTEGER { type1(1), type2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "External link type associated with the default route advertised into the OSPF routing domain. Note that any operation on it will not take effect unless ospfMultiProcessOriginateDefaultRoute has firstly been enabled." DEFVAL { type2 } ::= { ospfMultiProcessSystemEntry 7 } ospfMultiProcessDefaultExternalMetric OBJECT-TYPE SYNTAX Integer32 (-1..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "Metric used for generating the default route. Note that any operation on it will not take effect unless ospfMultiProcessOriginateDefaultRoute has firstly been enabled; '-1' is only for 'unset', that will destroy this metric value." ::= { ospfMultiProcessSystemEntry 8 } ospfMultiProcessSpfHoldTime OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the hold time between two consecutive SPF calculations." DEFVAL { 10 } ::= { ospfMultiProcessSystemEntry 9 } ospfMultiProcessAreaNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Records the OSPF area numbers." DEFVAL { 0 } ::= { ospfMultiProcessSystemEntry 10 } ospfMultiProcessAreaLimit OBJECT-TYPE SYNTAX Gauge32(1..4294967294) MAX-ACCESS read-write STATUS current DESCRIPTION "Max number of ospf area." DEFVAL { 4294967294 } ::= { ospfMultiProcessSystemEntry 11 } ospfMultiProcessSystemStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. Currently only support 4 status: 1. active 2. notInService 4. createAndGo 6. destroy ('active' and 'notInservice' status are used for getting action, 'createAndGo' and 'destroy' status are used for setting action.) - 'active', which indicates that the current OSPF instance exists in - the system. - 'notInService', if not exist in the system. - 'createAndGo', set this status to create an OSPF instance. - 'destroy', to delete an OSPF instance." ::= { ospfMultiProcessSystemEntry 17 } ospfMultiProcessRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-write STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses. This object is persistent and when written the entity SHOULD save the change to non-volatile storage. This is a private substitution for ospfRouterId of RFC1253." ::= { ospfMultiProcessSystemEntry 18 } ospfMultiProcessAdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one interface; 'disabled' disables it on all interfaces. This is a private substitution for ospfAdminStat of RFC1253." ::= { ospfMultiProcessSystemEntry 19 } ospfMultiProcessVersionNumber OBJECT-TYPE SYNTAX INTEGER { version2 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current version number of the OSPF protocol is 2. This is a private substitution for ospfVersionNumber of RFC1253." ::= { ospfMultiProcessSystemEntry 20 } ospfMultiProcessAreaBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A flag to note whether this router is an Area Border Router. This is a private substitution for ospfAreaBdrRtrStatus of RFC1253." ::= { ospfMultiProcessSystemEntry 21 } ospfMultiProcessASBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A flag to note whether this router is configured as an Autonomous System Border Router. This is a private substitution for ospfAreaBdrRtrStatus of RFC1253." ::= { ospfMultiProcessSystemEntry 22 } ospfMultiProcessExternLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of external (LS type-5) link state advertisements in the link state database. This is a private substitution for ospfExternLsaCount of RFC1253." ::= { ospfMultiProcessSystemEntry 23 } ospfMultiProcessExternLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit sum of the LS checksums of the external link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database and to compare the link state database of two routers. The value should be treated as unsigned when comparing two sums of checksums. This is a private substitution for ospfExternLsaCksumSum of RFC1253." ::= { ospfMultiProcessSystemEntry 24 } ospfMultiProcessOriginateNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of new link state advertisements that have been originated. This number is incremented each time the router originates a new LSA. Discontinuities in the value of this counter can occur at re-initialization of the management system. This is a private substitution for ospfOriginateNewLsas of RFC1253." ::= { ospfMultiProcessSystemEntry 25 } ospfMultiProcessRxNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of link state advertisements received that are determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements. Discontinuities in the value of this counter can occur at re-initialization of the management system. This is a private substitution for ospfRxNewLsas of RFC1253." ::= { ospfMultiProcessSystemEntry 26 } ospfMultiProcessAsLsaCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AS-scope link state advertisements in the AS-scope link state database. This is a private substitution for ospfAsLsaCount of RFC4750." ::= { ospfMultiProcessSystemEntry 30 } ospfMultiProcessSpfDelayTime OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the delay between receiving a change to SPF calculation." DEFVAL { 5 } ::= { ospfMultiProcessSystemEntry 31 } ospfMultiProcessDefaultMetric OBJECT-TYPE SYNTAX Integer32 (-1..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "The default metric for all redistributed routes. If the value is -1, then there is no default metric." ::= { ospfMultiProcessSystemEntry 33 } ospfMultiProcessNssaTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessNssaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptually table for ospfNssaEntry." ::= { ospfMgt 9 } ospfMultiProcessNssaEntry OBJECT-TYPE SYNTAX OspfMultiProcessNssaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptually row for ospfNssaTable." INDEX { ospfMultiProcessProcessId, ospfMultiProcessNssaAreaId } ::= { ospfMultiProcessNssaTable 1 } OspfMultiProcessNssaEntry ::= SEQUENCE { ospfMultiProcessNssaAreaId Unsigned32, ospfMultiProcessNssaTranslatorRole INTEGER, ospfMultiProcessNssaRedistributeStatus EnabledStatus, ospfMultiProcessNssaOriginateDefaultInfoStatus EnabledStatus, ospfMultiProcessNssaMetricType INTEGER, ospfMultiProcessNssaMetric Integer32, ospfMultiProcessNssaStatus RowStatus, ospfMultiProcessNssaTranslatorState INTEGER } ospfMultiProcessNssaAreaId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The 32-bit identifier for the NSSA. On creation, this can be derived from the instance." ::= { ospfMultiProcessNssaEntry 1 } ospfMultiProcessNssaTranslatorRole OBJECT-TYPE SYNTAX INTEGER { never(1), always(2), candidate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify NSSA-ABR translator-role. Candidate: Router may translate NSSA-LSA to Type-5 LSA if it is elected. Never: Router never translate NSSA-LSA. Always: Router always translate NSSA-LSA to Type-5 LSA." ::= { ospfMultiProcessNssaEntry 2 } ospfMultiProcessNssaRedistributeStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Enabled or disabled to import routes only into the normal areas, but not into the NSSA area." DEFVAL { enabled } ::= { ospfMultiProcessNssaEntry 3 } ospfMultiProcessNssaOriginateDefaultInfoStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable to generate a Type 7 default into the NSSA area." DEFVAL { disabled } ::= { ospfMultiProcessNssaEntry 4 } ospfMultiProcessNssaMetricType OBJECT-TYPE SYNTAX INTEGER { type1(1), type2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify NSSA external metric type." DEFVAL { type2 } ::= { ospfMultiProcessNssaEntry 5 } ospfMultiProcessNssaMetric OBJECT-TYPE SYNTAX Integer32(0..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify NSSA external metric value." DEFVAL { 1 } ::= { ospfMultiProcessNssaEntry 6 } ospfMultiProcessNssaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. Currently only support 4 status: 1. active 2. notInService 4. createAndGo 6. destroy ('active' and 'notInservice' status are used for getting action, 'createAndGo' and 'destroy' status are used for setting action.) - 'active',which indicates that the current NSSA exists in the system. - 'notInService', if not exist in the system. - 'createAndGo', set this status to create a NSSA instance. - 'destroy', to delete a NSSA instance." ::= { ospfMultiProcessNssaEntry 7 } ospfMultiProcessNssaTranslatorState OBJECT-TYPE SYNTAX INTEGER { enabled (1), elected (2), disabled (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if and how an NSSA border router is performing NSSA translation of type-7 LSAs into type-5 LSAs. When this object is set to enabled, the NSSA Border router's OspfAreaNssaExtTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is Translating type-7 LSAs into type-5.When this object is set to disabled, a candidate NSSA border router is NOT translating type-7 LSAs into type-5." ::= { ospfMultiProcessNssaEntry 8 } ospfMultiProcessRedistributeTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of all of ospfRedistributeEntry." ::= { ospfMgt 10 } ospfMultiProcessRedistributeEntry OBJECT-TYPE SYNTAX OspfMultiProcessRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for ospfRedistributeTable." INDEX { ospfMultiProcessProcessId, ospfMultiProcessRedistributeProtocol } ::= { ospfMultiProcessRedistributeTable 1 } OspfMultiProcessRedistributeEntry ::= SEQUENCE { ospfMultiProcessRedistributeProtocol INTEGER, ospfMultiProcessRedistributeMetricType INTEGER, ospfMultiProcessRedistributeMetric BigMetric, ospfMultiProcessRedistributeTag Gauge32, ospfMultiProcessRedistributeFilterListName DisplayString, ospfMultiProcessRedistributeStatus RowStatus, ospfMultiProcessRedistributeRoutemapName DisplayString } ospfMultiProcessRedistributeProtocol OBJECT-TYPE SYNTAX INTEGER { rip(1), static(2), connected(3), bgp(4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Protocol ID, type of the redistribute." ::= { ospfMultiProcessRedistributeEntry 1 } ospfMultiProcessRedistributeMetricType OBJECT-TYPE SYNTAX INTEGER { type1(1), type2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Metric type." DEFVAL { type2 } ::= { ospfMultiProcessRedistributeEntry 2 } ospfMultiProcessRedistributeMetric OBJECT-TYPE SYNTAX BigMetric MAX-ACCESS read-write STATUS current DESCRIPTION "Metric value." ::= { ospfMultiProcessRedistributeEntry 3 } ospfMultiProcessRedistributeTag OBJECT-TYPE SYNTAX Gauge32(0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The external route tag. " ::= { ospfMultiProcessRedistributeEntry 4 } ospfMultiProcessRedistributeFilterListName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "List name of access filter which use in other routing protocols." ::= { ospfMultiProcessRedistributeEntry 5 } ospfMultiProcessRedistributeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. Currently only support 4 status: 1. active 2. notInService 4. createAndGo 6. destroy ('active' and 'notInservice' status are used for getting action, 'createAndGo' and 'destroy' status are used for setting action.) - 'active', which indicates that the current type of redistribute - exists in the system. - 'notInService', if not exist in the system. - 'createAndGo', set this status to create a type of redistribute - instance. - 'destroy', to delete a type of redistribute instance." ::= { ospfMultiProcessRedistributeEntry 6 } ospfMultiProcessRedistributeRoutemapName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name of the route map. " ::= { ospfMultiProcessRedistributeEntry 7 } ospfMultiProcessSummaryAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessSummaryAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of all of ospfSummaryAddressEntry. " ::= { ospfMgt 11 } ospfMultiProcessSummaryAddressEntry OBJECT-TYPE SYNTAX OspfMultiProcessSummaryAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for ospfSummaryAddressTable. " INDEX { ospfMultiProcessProcessId, ospfMultiProcessSummaryAddressType, ospfMultiProcessSummaryAddress, ospfMultiProcessSummaryPfxLen } ::= { ospfMultiProcessSummaryAddressTable 1 } OspfMultiProcessSummaryAddressEntry ::= SEQUENCE { ospfMultiProcessSummaryAddressType InetAddressType, ospfMultiProcessSummaryAddress InetAddress, ospfMultiProcessSummaryPfxLen InetAddressPrefixLength, ospfMultiProcessSummaryStatus RowStatus } ospfMultiProcessSummaryAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Summary address type. " ::= { ospfMultiProcessSummaryAddressEntry 1 } ospfMultiProcessSummaryAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Summary address." ::= { ospfMultiProcessSummaryAddressEntry 2 } ospfMultiProcessSummaryPfxLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "Summary address prefix length." ::= { ospfMultiProcessSummaryAddressEntry 3 } ospfMultiProcessSummaryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. Currently only support 4 status: 1. active 2. notInService 4. createAndGo 6. destroy ('active' and 'notInservice' status are used for getting action, 'createAndGo' and 'destroy' status are used for setting action.) - 'active', which indicates that the current summary address exists in - the system. - 'notInService', if not exist in the system. - 'createAndGo', set this status to create a summary address. - 'destroy', to delete a summary address. " ::= { ospfMultiProcessSummaryAddressEntry 4 } ospfMultiProcessNetworkAreaAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessNetworkAreaAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of all of ospfNetworkAreaAddressEntry." ::= { ospfMgt 12 } ospfMultiProcessNetworkAreaAddressEntry OBJECT-TYPE SYNTAX OspfMultiProcessNetworkAreaAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row for ospfNetworkAreaAddressTable." INDEX { ospfMultiProcessProcessId, ospfMultiProcessNetworkAreaAddressType, ospfMultiProcessNetworkAreaAddress, ospfMultiProcessNetworkAreaPfxLen } ::= { ospfMultiProcessNetworkAreaAddressTable 1 } OspfMultiProcessNetworkAreaAddressEntry ::= SEQUENCE { ospfMultiProcessNetworkAreaAddressType InetAddressType, ospfMultiProcessNetworkAreaAddress InetAddress, ospfMultiProcessNetworkAreaPfxLen InetAddressPrefixLength, ospfMultiProcessNetworkAreaAreaId Unsigned32, ospfMultiProcessNetworkAreaStatus RowStatus, ospfMultiProcessNetworkAreaAreaId2 AreaID } ospfMultiProcessNetworkAreaAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "NetworkArea address type." ::= { ospfMultiProcessNetworkAreaAddressEntry 1 } ospfMultiProcessNetworkAreaAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "NetworkArea address. " ::= { ospfMultiProcessNetworkAreaAddressEntry 2 } ospfMultiProcessNetworkAreaPfxLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "NetworkArea prefix length. " ::= { ospfMultiProcessNetworkAreaAddressEntry 3 } ospfMultiProcessNetworkAreaAreaId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "NetworkArea area ID. " ::= { ospfMultiProcessNetworkAreaAddressEntry 4 } ospfMultiProcessNetworkAreaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. Currently only support 4 status: 1. active 2. notInService 4. createAndGo 6. destroy ('active' and 'notInservice' status are used for getting action, 'createAndGo' and 'destroy' status are used for setting action.) - 'active', which indicates that the current network exists in the - system. - 'notInService', if not exist in the system. - 'createAndGo', set this status to create a network. - 'destroy', to delete a network. " ::= { ospfMultiProcessNetworkAreaAddressEntry 5 } ospfMultiProcessNetworkAreaAreaId2 OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-write STATUS current DESCRIPTION "NetworkArea area ID as IP address format." ::= { ospfMultiProcessNetworkAreaAddressEntry 6 } --Ospf interface Table ospfMultiProcessIfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Table describes the interfaces from the viewpoint of OSPF. " ::= { ospfMgt 14 } ospfMultiProcessIfEntry OBJECT-TYPE SYNTAX OspfMultiProcessIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Entry describes one interface from the viewpoint of OSPF." INDEX { ospfMultiProcessIfIpAddressType, ospfMultiProcessIfIpAddress } ::= { ospfMultiProcessIfTable 1 } OspfMultiProcessIfEntry ::= SEQUENCE { ospfMultiProcessIfIpAddressType InetAddressType, ospfMultiProcessIfIpAddress InetAddress, ospfMultiProcessIfCost Integer32, ospfMultiProcessIfMtu Integer32, ospfMultiProcessIfMtuIgnore INTEGER, ospfMultiProcessIfAreaId AreaID, ospfMultiProcessIfRtrPriority DesignatedRouterPriority, ospfMultiProcessIfTransitDelay UpToMaxAge, ospfMultiProcessIfRetransInterval UpToMaxAge, ospfMultiProcessIfHelloInterval HelloRange, ospfMultiProcessIfRtrDeadInterval PositiveInteger, ospfMultiProcessIfState INTEGER, ospfMultiProcessIfDesignatedRouter IpAddress, ospfMultiProcessIfBackupDesignatedRouter IpAddress, ospfMultiProcessIfEvents Counter32, ospfMultiProcessIfAuthKey OCTET STRING, ospfMultiProcessIfStatus RowStatus, ospfMultiProcessIfAuthType OspfAuthenticationType, ospfMultiProcessIfDesignatedRouterId RouterID, ospfMultiProcessIfBackupDesignatedRouterId RouterID } ospfMultiProcessIfIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address type of this OSPF interface. " ::= { ospfMultiProcessIfEntry 1 } ospfMultiProcessIfIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of this OSPF interface. " ::= { ospfMultiProcessIfEntry 2 } ospfMultiProcessIfCost OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The output cost of this OSPF interface. Set 0 means unset the cost, thus the cost is dependent on ospfMultiProcessAutoCost. " ::= { ospfMultiProcessIfEntry 3 } ospfMultiProcessIfMtu OBJECT-TYPE SYNTAX Integer32 (576..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The mtu of this OSPF interface. Set 0 to unset the mtu. " ::= { ospfMultiProcessIfEntry 4 } ospfMultiProcessIfMtuIgnore OBJECT-TYPE SYNTAX INTEGER { check(0), ignore(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If check(0), OSPF will check the MTU size during DD (Database Description) exchange. If ignore(1), OSPF will not check the MTU size during DD exchange. " ::= { ospfMultiProcessIfEntry 5 } ospfMultiProcessIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone. This is a private substitution for ospfIfAreaId of RFC1253." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfMultiProcessIfEntry 6 } ospfMultiProcessIfRtrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority(0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker. This is a private substitution for ospfIfRtrPriority of RFC1253. " DEFVAL { 1 } ::= { ospfMultiProcessIfEntry 7 } ospfMultiProcessIfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge (1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface. Note that the minimal value SHOULD be 1 second. This is a private substitution for ospfIfTransitDelay of RFC1253. " DEFVAL { 1 } ::= { ospfMultiProcessIfEntry 8 } ospfMultiProcessIfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and Link State request packets. Note that minimal value SHOULD be 1 second. This is a private substitution for ospfIfRetransInterval of RFC1253. " DEFVAL { 5 } ::= { ospfMultiProcessIfEntry 9 } ospfMultiProcessIfHelloInterval OBJECT-TYPE SYNTAX HelloRange(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network. This is a private substitution for ospfIfHelloInterval of RFC1253. " DEFVAL { 10 } ::= { ospfMultiProcessIfEntry 10 } ospfMultiProcessIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network. Note that 1..65535 is for 'set' range ; The read value may be (1...65535)*4 by default according to the Hello interval if this dead interval have not been set. This is a private substitution for ospfIfRtrDeadInterval of RFC1253." DEFVAL { 40 } ::= { ospfMultiProcessIfEntry 11 } ospfMultiProcessIfState OBJECT-TYPE SYNTAX INTEGER { down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Interface State. This is a private substitution for ospfIfState of RFC1253." DEFVAL { down } ::= { ospfMultiProcessIfEntry 12 } ospfMultiProcessIfDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the designated router. This is a private substitution for ospfIfDesignatedRouter of RFC1253." ::= { ospfMultiProcessIfEntry 13 } ospfMultiProcessIfBackupDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the backup designated router. This is a private substitution for ospfIfBackupDesignatedRouter of RFC1253." ::= { ospfMultiProcessIfEntry 14 } ospfMultiProcessIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this OSPF interface has changed its state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system. This is a private substitution for ospfIfEvents of RFC1253. " ::= { ospfMultiProcessIfEntry 15 } ospfMultiProcessIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "The cleartext password used as an OSPF authentication key when simplePassword security is enabled. This object does not access any OSPF cryptogaphic (e.g., MD5) authentication key under any circumstance. If the key length is shorter than 8 octets, th agent will left adjust and zero fill to 8 octets. Unauthenticated interfaces need no authentication key, and simple password authentication cannot us a key of more than 8 octets. Note that the use of simplePassword authentication is NOT recommended when there is concern regarding attack upon the OSPF system. SimplePassword authentication is only sufficient to protect against accidental misconfigurations because it re-uses cleartext passwords [RFC1704]. When read, ospfIfAuthKey always returns an octet string of length zero. This is a private substitution for ospfIfAuthKey of RFC1253." ::= { ospfMultiProcessIfEntry 16 } ospfMultiProcessIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This variable display the status of the ospf interface. Currently only active and notInService statues are supported. The value of this object has no effect on whether other objects in this conceptual row can be modified. This is a private substitution for ospfIfStatus of RFC1253. " ::= { ospfMultiProcessIfEntry 17 } ospfMultiProcessIfAuthType OBJECT-TYPE SYNTAX OspfAuthenticationType MAX-ACCESS read-write STATUS current DESCRIPTION "The authentication type specified for an interface. Note that this object can be used to engage in significant attacks against an OSPF router. This is a private substitution for ospfIfAuthType of RFC1253. " DEFVAL { none } -- no authentication, by default ::= { ospfMultiProcessIfEntry 18 } ospfMultiProcessIfDesignatedRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the designated router. This is a private substitution for ospfIfDesignatedRouterId of RFC4750. " ::= { ospfMultiProcessIfEntry 19 } ospfMultiProcessIfBackupDesignatedRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the backup designated router. This is a private substitution for ospfIfBackupDesignatedRouterId of RFC4750." ::= { ospfMultiProcessIfEntry 20 } -- OSPF Area Table -- The OSPF Area Table contains information -- regarding the various areas. ospfMultiProcessAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the configured parameters and cumulative statistics of the router's attached areas. The interfaces and virtual links are configured as part of these areas. Area 0.0.0.0, by definition, is the backbone area. This is a private substitution for ospfAreaTable of RFC1253." ::= { ospfMgt 15 } ospfMultiProcessAreaEntry OBJECT-TYPE SYNTAX OspfMultiProcessAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the configured parameters and cumulative statistics of one of the router's attached areas. The interfaces and virtual links are configured as part of these areas. Area 0.0.0.0, by definition, is the backbone area. Information in this table is persistent and when this object is written the entity SHOULD save the change to non-volatile storage. " INDEX { ospfMultiProcessProcessId, ospfMultiProcessAreaId } ::= { ospfMultiProcessAreaTable 1 } OspfMultiProcessAreaEntry ::= SEQUENCE { ospfMultiProcessAreaId AreaID, ospfMultiProcessAuthType OspfAuthenticationType, ospfMultiProcessImportAsExtern INTEGER, ospfMultiProcessSpfRuns Counter32, ospfMultiProcessAreaBdrRtrCount Gauge32, ospfMultiProcessAsBdrRtrCount Gauge32, ospfMultiProcessAreaLsaCount Gauge32, ospfMultiProcessAreaLsaCksumSum Integer32, ospfMultiProcessAreaSummary INTEGER, ospfMultiProcessAreaStatus RowStatus } ospfMultiProcessAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS not-accessible -- read-only since originally -- an SMIv1 index STATUS current DESCRIPTION "A 32-bit integer uniquely identifying an area. " ::= { ospfMultiProcessAreaEntry 1 } ospfMultiProcessAuthType OBJECT-TYPE SYNTAX OspfAuthenticationType MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The authentication type specified for an area." DEFVAL { none } -- no authentication, by default ::= { ospfMultiProcessAreaEntry 2 } ospfMultiProcessImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal (1), importNoExternal (2), importNssa (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if an area is a stub area, NSSA, or standard area. Type-5 AS-external LSAs and type-11 Opaque LSAs are not imported into stub areas or NSSAs. NSSAs import AS-external data as type-7 LSAs. " DEFVAL { importExternal } ::= { ospfMultiProcessAreaEntry 3 } ospfMultiProcessSpfRuns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm. Discontinuities in the value of this counter can occur at re-initialization of the management system." ::= { ospfMultiProcessAreaEntry 4 } ospfMultiProcessAreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Area Border Routers reachable within this area. This is initially zero and is calculated in each Shortest Path First (SPF) pass. " ::= { ospfMultiProcessAreaEntry 5 } ospfMultiProcessAsBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Autonomous System Border Routers reachable within this area. This is initially zero and is calculated in each SPF pass. " ::= { ospfMultiProcessAreaEntry 6 } ospfMultiProcessAreaLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of link state advertisements in this area's link state database, excluding AS-external LSAs. " ::= { ospfMultiProcessAreaEntry 7 } ospfMultiProcessAreaLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit sum of the link state advertisements' LS checksums contained in this area's link state database. This sum excludes external (LS type-5) link state advertisements. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers. The value should be treated as unsigned when comparing two sums of checksums." DEFVAL { 0 } ::= { ospfMultiProcessAreaEntry 8 } ospfMultiProcessAreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary (1), sendAreaSummary (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable controls the import of summary LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will not originate summary LSAs into the stub or NSSA area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs." DEFVAL { sendAreaSummary } ::= { ospfMultiProcessAreaEntry 9 } ospfMultiProcessAreaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Row status of area. Note ospf area can't be created or destroyed solely in this table. Only read is permitted. The value of this object has no effect on whether other objects in this conceptual row can be modified. " ::= { ospfMultiProcessAreaEntry 10 } -- OSPF Area Default Metric Table ospfMultiProcessStubAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessStubAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The set of metrics that will be advertised by a default Area Border Router into a stub area. This is a private substitution for ospfStubAreaTable of RFC1253." ::= { ospfMgt 16 } ospfMultiProcessStubAreaEntry OBJECT-TYPE SYNTAX OspfMultiProcessStubAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The metric for a given Type of Service that will be advertised by a default Area Border Router into a stub area. Information in this table is persistent and when this object is written the entity SHOULD save the change to non-volatile storage." INDEX { ospfMultiProcessProcessId, ospfMultiProcessStubAreaId, ospfMultiProcessStubTOS } ::= { ospfMultiProcessStubAreaTable 1 } OspfMultiProcessStubAreaEntry ::= SEQUENCE { ospfMultiProcessStubAreaId AreaID, ospfMultiProcessStubTOS TOSType, ospfMultiProcessStubMetric BigMetric, ospfMultiProcessStubStatus RowStatus } ospfMultiProcessStubAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The 32-bit identifier for the stub area. On creation, this can be derived from the instance." ::= { ospfMultiProcessStubAreaEntry 1 } ospfMultiProcessStubTOS OBJECT-TYPE SYNTAX TOSType MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The Type of Service associated with the metric. On creation, this can be derived from the instance. Currently only support TOS=0." ::= { ospfMultiProcessStubAreaEntry 2 } ospfMultiProcessStubMetric OBJECT-TYPE SYNTAX BigMetric(0..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The metric value applied at the indicated Type of Service. By default, this equals the least metric at the Type of Service among the interfaces to other areas." ::= { ospfMultiProcessStubAreaEntry 3 } ospfMultiProcessStubStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction, and destruction. Currently set only support 'createAndGo' and 'destroy'. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { ospfMultiProcessStubAreaEntry 4 } -- OSPF Link State Database ospfMultiProcessLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's link state database (LSDB). The LSDB contains the link state advertisements from throughout the areas that the device is attached to. This is a private substitution for ospfLsdbTable of RFC1253." ::= { ospfMgt 17 } ospfMultiProcessLsdbEntry OBJECT-TYPE SYNTAX OspfMultiProcessLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single link state advertisement." INDEX { ospfMultiProcessProcessId, ospfMultiProcessLsdbAreaId, ospfMultiProcessLsdbType, ospfMultiProcessLsdbLsid, ospfMultiProcessLsdbRouterId } ::= { ospfMultiProcessLsdbTable 1 } OspfMultiProcessLsdbEntry ::= SEQUENCE { ospfMultiProcessLsdbAreaId AreaID, ospfMultiProcessLsdbType INTEGER, ospfMultiProcessLsdbLsid IpAddress, ospfMultiProcessLsdbRouterId RouterID, ospfMultiProcessLsdbSequence Integer32, ospfMultiProcessLsdbAge Integer32, ospfMultiProcessLsdbChecksum Integer32, ospfMultiProcessLsdbAdvertisement OCTET STRING } ospfMultiProcessLsdbAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The 32-bit identifier of the area from which the LSA was received." ::= { ospfMultiProcessLsdbEntry 1 } ospfMultiProcessLsdbType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), -- but see ospfAsLsdbTable multicastLink (6), nssaExternalLink (7), areaOpaqueLink (10) } MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertisement format. Note: External link state advertisements are permitted for backward compatibility, but should be displayed in the ospfMultiProcessExtLsdbTable rather than here. " ::= { ospfMultiProcessLsdbEntry 2 } ospfMultiProcessLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP address; It identifies the piece of the routing domain that is being described by the advertisement. " ::= { ospfMultiProcessLsdbEntry 3 } ospfMultiProcessLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The 32-bit number that uniquely identifies the originating router in the Autonomous System. " ::= { ospfMultiProcessLsdbEntry 4 } ospfMultiProcessLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate Link State Advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement." ::= { ospfMultiProcessLsdbEntry 5 } ospfMultiProcessLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge, except when -- doNotAge bit is set UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state advertisement in seconds. " ::= { ospfMultiProcessLsdbEntry 6 } ospfMultiProcessLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. " ::= { ospfMultiProcessLsdbEntry 7 } ospfMultiProcessLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire link state advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size." ::= { ospfMultiProcessLsdbEntry 8 } -- OSPF Virtual Interface Table ospfMultiProcessVirtIfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessVirtIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about this router's virtual interfaces that the OSPF Process is configured to carry on. This is a private substitution for ospfVirtIfTable of RFC1253. " ::= { ospfMgt 20 } ospfMultiProcessVirtIfEntry OBJECT-TYPE SYNTAX OspfMultiProcessVirtIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single virtual interface. Information in this table is persistent and when this object is written the entity SHOULD save the change to non-volatile storage. " INDEX { ospfMultiProcessProcessId, ospfMultiProcessVirtIfAreaId, ospfMultiProcessVirtIfNeighbor } ::= { ospfMultiProcessVirtIfTable 1 } OspfMultiProcessVirtIfEntry ::= SEQUENCE { ospfMultiProcessVirtIfAreaId AreaID, ospfMultiProcessVirtIfNeighbor RouterID, ospfMultiProcessVirtIfTransitDelay UpToMaxAge, ospfMultiProcessVirtIfRetransInterval UpToMaxAge, ospfMultiProcessVirtIfHelloInterval HelloRange, ospfMultiProcessVirtIfRtrDeadInterval PositiveInteger, ospfMultiProcessVirtIfState INTEGER, ospfMultiProcessVirtIfEvents Counter32, ospfMultiProcessVirtIfAuthKey OCTET STRING, ospfMultiProcessVirtIfStatus RowStatus, ospfMultiProcessVirtIfAuthType OspfAuthenticationType } ospfMultiProcessVirtIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The transit area that the virtual link traverses. By definition, this is not 0.0.0.0. " ::= { ospfMultiProcessVirtIfEntry 1 } ospfMultiProcessVirtIfNeighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The Router ID of the virtual neighbor. " ::= { ospfMultiProcessVirtIfEntry 2 } ospfMultiProcessVirtIfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a Link State update packet over this interface. Note that the minimal value SHOULD be 1 second." DEFVAL { 1 } ::= { ospfMultiProcessVirtIfEntry 3 } ospfMultiProcessVirtIfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds between link state avertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and Link State request packets. This value should be well over the expected round-trip time. Note that the minimal value SHOULD be 1 second. " DEFVAL { 5 } ::= { ospfMultiProcessVirtIfEntry 4 } ospfMultiProcessVirtIfHelloInterval OBJECT-TYPE SYNTAX HelloRange(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { ospfMultiProcessVirtIfEntry 5 } ospfMultiProcessVirtIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger(1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be 4 multiple of the Hello interval. This value must be the same for the virtual neighbor. Note that 1..65535 is for 'set' range ; The read value may be (1...65535)*4 by default according to the Hello interval if this dead interval haven't been set. " DEFVAL { 40 } ::= { ospfMultiProcessVirtIfEntry 6 } ospfMultiProcessVirtIfState OBJECT-TYPE SYNTAX INTEGER { down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF virtual interface states. " DEFVAL { down } ::= { ospfMultiProcessVirtIfEntry 7 } ospfMultiProcessVirtIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of state changes or error events on this virtual link. Discontinuities in the value of this counter can occur at re-initialization of the management system." ::= { ospfMultiProcessVirtIfEntry 8 } ospfMultiProcessVirtIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "The cleartext password used as an OSPF authentication key when simplePassword security is enabled. This object does not access any OSPF cryptogaphic (e.g., MD5) authentication key under any circumstance. If the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Unauthenticated interfaces need no authentication key, and simple password authentication cannot use a key of more than 8 octets. Note that the use of simplePassword authentication is NOT recommended when there is concern regarding attack upon the OSPF system. SimplePassword authentication is only sufficient to protect against accidental misconfigurations because it re-uses cleartext passwords. [RFC1704] When read, ospfVirtIfAuthKey always returns an octet string of length zero. " ::= { ospfMultiProcessVirtIfEntry 9 } ospfMultiProcessVirtIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. " ::= { ospfMultiProcessVirtIfEntry 10 } ospfMultiProcessVirtIfAuthType OBJECT-TYPE SYNTAX OspfAuthenticationType MAX-ACCESS read-write STATUS current DESCRIPTION "The authentication type specified for a virtual interface. Note that this object can be used to engage in significant attacks against an OSPF router." DEFVAL { none } -- no authentication, by default ::= { ospfMultiProcessVirtIfEntry 11 } -- OSPF Neighbor Table ospfMultiProcessNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table describing all non-virtual neighbors in the locality of the OSPF router. This is a private substitution for ospfNbrTable of RFC1253." ::= { ospfMgt 21 } ospfMultiProcessNbrEntry OBJECT-TYPE SYNTAX OspfMultiProcessNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single neighbor. " INDEX { ospfMultiProcessProcessId, ospfMultiProcessNbrIpAddr } ::= { ospfMultiProcessNbrTable 1 } OspfMultiProcessNbrEntry ::= SEQUENCE { ospfMultiProcessNbrIpAddr IpAddress, ospfMultiProcessNbrRtrId RouterID, ospfMultiProcessNbrOptions Integer32, ospfMultiProcessNbrPriority DesignatedRouterPriority, ospfMultiProcessNbrState INTEGER, ospfMultiProcessNbrEvents Counter32, ospfMultiProcessNbrLsRetransQLen Gauge32 } ospfMultiProcessNbrIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The IP address this neighbor is using in its IP source address." ::= { ospfMultiProcessNbrEntry 1 } ospfMultiProcessNbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS not-accessible STATUS current DESCRIPTION "A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System. " ::= { ospfMultiProcessNbrEntry 2 } ospfMultiProcessNbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A bit mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external information; if zero, it is a stub area. Bit 2, if set, indicates that the system is capable of routing IP multicast datagrams, that is that it implements the multicast extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type-7 external advertisements, which are translated into type-5 external advertisements at NSSA borders. " DEFVAL { 0 } ::= { ospfMultiProcessNbrEntry 3 } ospfMultiProcessNbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-only STATUS current DESCRIPTION "The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network. " DEFVAL { 1 } ::= { ospfMultiProcessNbrEntry 4 } ospfMultiProcessNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the relationship with this neighbor." DEFVAL { down } ::= { ospfMultiProcessNbrEntry 5 } ospfMultiProcessNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this neighbor relationship has changed state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system. " ::= { ospfMultiProcessNbrEntry 6 } ospfMultiProcessNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue. " ::= { ospfMultiProcessNbrEntry 7 } -- OSPF Virtual Neighbor Table ospfMultiProcessVirtNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessVirtNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes all virtual neighbors. Since virtual links are configured in the Virtual Interface Table, this table is read-only. This is a private substitution for ospfVirtNbrTable of RFC1253. " ::= { ospfMgt 22 } ospfMultiProcessVirtNbrEntry OBJECT-TYPE SYNTAX OspfMultiProcessVirtNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Virtual neighbor information." INDEX { ospfMultiProcessProcessId, ospfMultiProcessVirtNbrArea, ospfMultiProcessVirtNbrRtrId } ::= { ospfMultiProcessVirtNbrTable 1 } OspfMultiProcessVirtNbrEntry ::= SEQUENCE { ospfMultiProcessVirtNbrArea AreaID, ospfMultiProcessVirtNbrRtrId RouterID, ospfMultiProcessVirtNbrIpAddr IpAddress, ospfMultiProcessVirtNbrOptions Integer32, ospfMultiProcessVirtNbrState INTEGER, ospfMultiProcessVirtNbrEvents Counter32, ospfMultiProcessVirtNbrLsRetransQLen Gauge32 } ospfMultiProcessVirtNbrArea OBJECT-TYPE SYNTAX AreaID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The Transit Area Identifier. " ::= { ospfMultiProcessVirtNbrEntry 1 } ospfMultiProcessVirtNbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the neighboring router in the Autonomous System." ::= { ospfMultiProcessVirtNbrEntry 2 } ospfMultiProcessVirtNbrIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address this virtual neighbor is using. " ::= { ospfMultiProcessVirtNbrEntry 3 } ospfMultiProcessVirtNbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A bit mask corresponding to the neighbor's options field. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 2, if set, indicates that the system is network multicast capable, i.e., that it implements OSPF multicast routing." ::= { ospfMultiProcessVirtNbrEntry 4 } ospfMultiProcessVirtNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the virtual neighbor relationship." ::= { ospfMultiProcessVirtNbrEntry 5 } ospfMultiProcessVirtNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this virtual link has changed its state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system." ::= { ospfMultiProcessVirtNbrEntry 6 } ospfMultiProcessVirtNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue." ::= { ospfMultiProcessVirtNbrEntry 7 } -- OSPF Link State Database, External ospfMultiProcessExtLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's external LSA link state database. This table is identical to the OSPF LSDB Table in format, but contains only external link state advertisements. The purpose is to allow external LSAs to be displayed once for the router rather than once in each non-stub area. Note that external LSAs are also in the AS-scope link state database. This is a private substitution for ospfExtLsdbTable of RFC1253." ::= { ospfMgt 23 } ospfMultiProcessExtLsdbEntry OBJECT-TYPE SYNTAX OspfMultiProcessExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single link state advertisement." INDEX { ospfMultiProcessProcessId, ospfMultiProcessExtLsdbType, ospfMultiProcessExtLsdbLsid, ospfMultiProcessExtLsdbRouterId } ::= { ospfMultiProcessExtLsdbTable 1 } OspfMultiProcessExtLsdbEntry ::= SEQUENCE { ospfMultiProcessExtLsdbType INTEGER, ospfMultiProcessExtLsdbLsid IpAddress, ospfMultiProcessExtLsdbRouterId RouterID, ospfMultiProcessExtLsdbSequence Integer32, ospfMultiProcessExtLsdbAge Integer32, ospfMultiProcessExtLsdbChecksum Integer32, ospfMultiProcessExtLsdbAdvertisement OCTET STRING } ospfMultiProcessExtLsdbType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (5) } MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertisement format. " ::= { ospfMultiProcessExtLsdbEntry 1 } ospfMultiProcessExtLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP address; it identifies the piece of the routing domain that is being described by the advertisement. " ::= { ospfMultiProcessExtLsdbEntry 2 } ospfMultiProcessExtLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The 32-bit number that uniquely identifies the originating router in the Autonomous System." ::= { ospfMultiProcessExtLsdbEntry 3 } ospfMultiProcessExtLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement." ::= { ospfMultiProcessExtLsdbEntry 4 } ospfMultiProcessExtLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge, except when -- doNotAge bit is set UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state advertisement in seconds. " ::= { ospfMultiProcessExtLsdbEntry 5 } ospfMultiProcessExtLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. " ::= { ospfMultiProcessExtLsdbEntry 6 } ospfMultiProcessExtLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE(36)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire link state advertisement, including its header." ::= { ospfMultiProcessExtLsdbEntry 7 } -- The OSPF Area Aggregate Table -- -- This table replaces the OSPF Area Summary Table, being an -- extension of that for CIDR routers. ospfMultiProcessAreaAggregateTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessAreaAggregateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Area Aggregate Table acts as an adjunct to the Area Table. It describes those address aggregates that are configured to be propagated from an area. Its purpose is to reduce the amount of information that is known beyond an Area's borders. It contains a set of IP address ranges specified by an IP address/IP network mask pair. For example, a class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are configured such that one range subsumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one. This is a private substitution for ospfAreaAggregateTable of RFC1253." ::= { ospfMgt 24 } ospfMultiProcessAreaAggregateEntry OBJECT-TYPE SYNTAX OspfMultiProcessAreaAggregateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single area aggregate entry. Information in this table is persistent and when this object is written the entity SHOULD save the change to non-volatile storage. " INDEX { ospfMultiProcessProcessId, ospfMultiProcessAreaAggregateAreaID, ospfMultiProcessAreaAggregateLsdbType, ospfMultiProcessAreaAggregateNet, ospfMultiProcessAreaAggregateMask } ::= { ospfMultiProcessAreaAggregateTable 1 } OspfMultiProcessAreaAggregateEntry ::= SEQUENCE { ospfMultiProcessAreaAggregateAreaID AreaID, ospfMultiProcessAreaAggregateLsdbType INTEGER, ospfMultiProcessAreaAggregateNet IpAddress, ospfMultiProcessAreaAggregateMask IpAddress, ospfMultiProcessAreaAggregateStatus RowStatus, ospfMultiProcessAreaAggregateEffect INTEGER } ospfMultiProcessAreaAggregateAreaID OBJECT-TYPE SYNTAX AreaID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The area within which the address aggregate is to be found." ::= { ospfMultiProcessAreaAggregateEntry 1 } ospfMultiProcessAreaAggregateLsdbType OBJECT-TYPE SYNTAX INTEGER { summaryLink (3) } MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The type of the address aggregate. This field specifies the Lsdb type that this address aggregate applies to." ::= { ospfMultiProcessAreaAggregateEntry 2 } ospfMultiProcessAreaAggregateNet OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The IP address of the net or subnet indicated by the range." ::= { ospfMultiProcessAreaAggregateEntry 3 } ospfMultiProcessAreaAggregateMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The subnet mask that pertains to the net or subnet. " ::= { ospfMultiProcessAreaAggregateEntry 4 } ospfMultiProcessAreaAggregateStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. " ::= { ospfMultiProcessAreaAggregateEntry 5 } ospfMultiProcessAreaAggregateEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching (1), doNotAdvertiseMatching (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (advertiseMatching) or result in the subnet's not being advertised at all outside the area. " DEFVAL { advertiseMatching } ::= { ospfMultiProcessAreaAggregateEntry 6 } -- OSPF Interface Message Digest Authentication Table ospfMultiProcessIfAuthMd5Table OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessIfAuthMd5Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Message Digest Authentication Table describes the interfaces from the viewpoint of OSPF." ::= { ospfMgt 27 } ospfMultiProcessIfAuthMd5Entry OBJECT-TYPE SYNTAX OspfMultiProcessIfAuthMd5Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Message Digest Authentication Entry describes one interface from the viewpoint of OSPF." INDEX { ospfMultiProcessIfAuthMd5IpAddressType, ospfMultiProcessIfAuthMd5IpAddress, ospfMultiProcessIfAuthMd5KeyId } ::= { ospfMultiProcessIfAuthMd5Table 1 } OspfMultiProcessIfAuthMd5Entry ::= SEQUENCE { ospfMultiProcessIfAuthMd5IpAddressType InetAddressType, ospfMultiProcessIfAuthMd5IpAddress InetAddress, ospfMultiProcessIfAuthMd5KeyId Integer32, ospfMultiProcessIfAuthMd5Key OCTET STRING } ospfMultiProcessIfAuthMd5IpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address type of this OSPF interface." ::= { ospfMultiProcessIfAuthMd5Entry 1 } ospfMultiProcessIfAuthMd5IpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of this OSPF interface. " ::= { ospfMultiProcessIfAuthMd5Entry 2 } ospfMultiProcessIfAuthMd5KeyId OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Message Digest Authentication key ID of this OSPF interface. " ::= { ospfMultiProcessIfAuthMd5Entry 3 } ospfMultiProcessIfAuthMd5Key OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Message Digest Authentication key of this OSPF interface. When read, ospfIfAuthMd5Key always returns an octet string of length zero. Set zero-length string to unset the md5 key." ::= { ospfMultiProcessIfAuthMd5Entry 4 } -- OSPF Virtual Link Interface Message Digest Authentication Table ospfMultiProcessVirtIfAuthMd5Table OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessVirtIfAuthMd5Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Virtual Interface Message Digest Authentication Table describes the interfaces from the viewpoint of OSPF." ::= { ospfMgt 28 } ospfMultiProcessVirtIfAuthMd5Entry OBJECT-TYPE SYNTAX OspfMultiProcessVirtIfAuthMd5Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Virtual Interface Message Digest Authentication Entry describes one interface from the viewpoint of OSPF. " INDEX { ospfMultiProcessProcessId, ospfMultiProcessVirtIfAuthMd5AreaId, ospfMultiProcessVirtIfAuthMd5Neighbor, ospfMultiProcessVirtIfAuthMd5KeyId } ::= { ospfMultiProcessVirtIfAuthMd5Table 1 } OspfMultiProcessVirtIfAuthMd5Entry ::= SEQUENCE { ospfMultiProcessVirtIfAuthMd5AreaId AreaID, ospfMultiProcessVirtIfAuthMd5Neighbor RouterID, ospfMultiProcessVirtIfAuthMd5KeyId Integer32, ospfMultiProcessVirtIfAuthMd5Key OCTET STRING } ospfMultiProcessVirtIfAuthMd5AreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The transit area that the virtual link traverses. By definition, this is not 0.0.0.0." ::= { ospfMultiProcessVirtIfAuthMd5Entry 1 } ospfMultiProcessVirtIfAuthMd5Neighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS not-accessible -- read-only since originally an -- SMIv1 index STATUS current DESCRIPTION "The Router ID of the virtual neighbor. " ::= { ospfMultiProcessVirtIfAuthMd5Entry 2 } ospfMultiProcessVirtIfAuthMd5KeyId OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Message Digest Authentication key ID of this OSPF virtual interface. " ::= { ospfMultiProcessVirtIfAuthMd5Entry 3 } ospfMultiProcessVirtIfAuthMd5Key OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Message Digest Authentication key of this OSPF virtual interface. When read, ospfVirtIfAuthMd5Key always returns an octet string of length zero. Set zero-length string to unset the md5 key." ::= { ospfMultiProcessVirtIfAuthMd5Entry 4 } --OSPF Route Table ospfMultiProcessRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfMultiProcessRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual table for ospfRouteEntry." ::= { ospfMgt 31 } ospfMultiProcessRouteEntry OBJECT-TYPE SYNTAX OspfMultiProcessRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptually row for ospfRouteTable." INDEX { ospfMultiProcessProcessId, ospfMultiProcessRouteDest, ospfMultiProcessRoutePfxLen, ospfMultiProcessRouteNexthop } ::= { ospfMultiProcessRouteTable 1 } OspfMultiProcessRouteEntry ::= SEQUENCE { ospfMultiProcessRouteDest IpAddress, ospfMultiProcessRoutePfxLen Integer32, ospfMultiProcessRouteNexthop IpAddress, ospfMultiProcessRouteInterface DisplayString, ospfMultiProcessRouteCost Unsigned32, ospfMultiProcessRoutePathType INTEGER, ospfMultiProcessRouteAreaId IpAddress, ospfMultiProcessRouteTransitArea INTEGER } ospfMultiProcessRouteDest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination IP address of this route. " ::= { ospfMultiProcessRouteEntry 1 } ospfMultiProcessRoutePfxLen OBJECT-TYPE SYNTAX Integer32(0..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The prefix length of this route." ::= { ospfMultiProcessRouteEntry 2 } ospfMultiProcessRouteNexthop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The nexthop IP address of this route. Note that, discard and directly connected routes have no nexthops. They are displayed as 0.0.0.0." ::= { ospfMultiProcessRouteEntry 3 } ospfMultiProcessRouteInterface OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of outgoing interface which links to nexthop. Return an octet string of length zero when it is discard route." ::= { ospfMultiProcessRouteEntry 4 } ospfMultiProcessRouteCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of this route. Always return 4294967295 if it is a discard route." ::= { ospfMultiProcessRouteEntry 5 } ospfMultiProcessRoutePathType OBJECT-TYPE SYNTAX INTEGER { unknown(0), connected(1), discard(2), intra(3), inter(4), type1(5), type2(6), nssa1(7), nssa2(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The path type of this route. unknown, unknown path type. connected, directly connected. discard, discard route. intra, intra-area route. inter, inter-area route. type1, external type 1 route. type2, external type 2 route. nssa1, nssa external type 1 route. nssa2, nssa external type 2 route." ::= { ospfMultiProcessRouteEntry 6 } ospfMultiProcessRouteAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Area ID of the path which links to nexthop. Note that, discard and external routes have no area option for the path. Always return 0.0.0.0." ::= { ospfMultiProcessRouteEntry 7 } ospfMultiProcessRouteTransitArea OBJECT-TYPE SYNTAX INTEGER { transitArea(1), normalArea(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "To display if the area is a transit area or not for the path. Note that, discard and external routes have no area option for the path. Always return normalArea(2)." ::= { ospfMultiProcessRouteEntry 8 } ospfIfParamTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfIfParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The TOS metrics for a non-virtual interface identified by the interface index." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" ::= { ospfMgt 37 } ospfIfParamEntry OBJECT-TYPE SYNTAX OspfIfParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A particular TOS metric for a non-virtual in- terface identified by the interface index." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" INDEX {ospfIfParamIfindex, ospfIfParamIpAddress, ospfIfParamTOS } ::= { ospfIfParamTable 1 } OspfIfParamEntry ::= SEQUENCE { ospfIfParamIfindex Integer32, ospfIfParamIpAddress IpAddress, ospfIfParamTOS TOSType, ospfIfParamCost Metric, ospfIfParamStatus ValidStatus } ospfIfParamIfindex OBJECT-TYPE SYNTAX Integer32(1001..5093) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Ifindex of this OSPF interface. On row creation, this can be derived from the instance." ::= { ospfIfParamEntry 1 } ospfIfParamIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of this OSPF interface. On row creation, this can be derived from the in- stance." ::= { ospfIfParamEntry 2 } ospfIfParamTOS OBJECT-TYPE SYNTAX TOSType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of service metric being referenced. On row creation, this can be derived from the instance." ::= { ospfIfParamEntry 3 } ospfIfParamCost OBJECT-TYPE SYNTAX Metric MAX-ACCESS read-write STATUS current DESCRIPTION "The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed." ::= { ospfIfParamEntry 4 } ospfIfParamStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry." ::= { ospfIfParamEntry 5 } -- routeMgt Table routeMultipath OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is the multipath numbers installed to FIB. The default value is 4." DEFVAL {4} ::={ routeMgt 3 } -- -- sysLogMgt -- -- Management for system log. This configures the logging -- of events inside the switch. sysLogStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether the system log is enabled." ::= { sysLogMgt 1 } sysLogHistoryFlashLevel OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Severity level for logging to flash." ::= { sysLogMgt 2 } sysLogHistoryRamLevel OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Severity level for logging to RAM." ::= { sysLogMgt 3 } -- --remoteLogMgt -- remoteLogMgt OBJECT IDENTIFIER ::= { sysLogMgt 6 } remoteLogStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether the remote log system is enabled." ::= { remoteLogMgt 1 } remoteLogLevel OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Severity level for remote log." ::= { remoteLogMgt 2 } remoteLogFacilityType OBJECT-TYPE SYNTAX INTEGER { localUse0(16), localUse1(17), localUse2(18), localUse3(19), localUse4(20), localUse5(21), localUse6(22), localUse7(23) } MAX-ACCESS read-write STATUS current DESCRIPTION " The facility type for remote log." ::= { remoteLogMgt 3 } --remoteLogServerInetTable remoteLogServerInetTable OBJECT-TYPE SYNTAX SEQUENCE OF RemoteLogServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for storing the remote log server list." ::= { remoteLogMgt 7 } remoteLogServerInetEntry OBJECT-TYPE SYNTAX RemoteLogServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for remoteLogServerInetTable." INDEX { remoteLogServerInetAddressType, remoteLogServerInetAddress} ::= { remoteLogServerInetTable 1 } RemoteLogServerInetEntry ::= SEQUENCE { remoteLogServerInetAddressType InetAddressType, remoteLogServerInetAddress InetAddress, remoteLogServerStatus ValidStatus, remoteLogServerUdpPort Integer32 } remoteLogServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the type of address denoted in remoteLogServerInetAddress type. Only ipv4(1), ipv6(2) and ipv6z(4) types are supported." ::= { remoteLogServerInetEntry 1 } remoteLogServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the remote log Server." ::= { remoteLogServerInetEntry 2 } remoteLogServerStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { remoteLogServerInetEntry 3 } remoteLogServerUdpPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The UDP port number of the remote log Server" ::= { remoteLogServerInetEntry 4 } -- --smtpMgt -- smtpMgt OBJECT IDENTIFIER ::= { sysLogMgt 7 } smtpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable the SMTP, set disabled(2) to disable the SMTP." ::= { smtpMgt 1 } smtpSeverityLevel OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the SMTP minimum severity level to send the event message." ::= { smtpMgt 2 } smtpSourceEMail OBJECT-TYPE SYNTAX DisplayString (SIZE(0..41)) MAX-ACCESS read-write STATUS current DESCRIPTION "SMTP source email address, the sender's mail address that appears in the 'From' field of the mail." ::= { smtpMgt 3 } --smtpServerIpTable smtpServerIpTable OBJECT-TYPE SYNTAX SEQUENCE OF SmtpServerIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SMTP server IP table. The maximum servers to be added is 3." ::= { smtpMgt 4 } smtpServerIpEntry OBJECT-TYPE SYNTAX SmtpServerIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the smtpServerIpTable." INDEX { smtpServerIp } ::= { smtpServerIpTable 1 } SmtpServerIpEntry ::= SEQUENCE { smtpServerIp IpAddress, smtpServerIpStatus ValidStatus } smtpServerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "SMTP mail server's IP address." ::= { smtpServerIpEntry 1 } smtpServerIpStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { smtpServerIpEntry 2 } --smtpDestEMailTable smtpDestEMailTable OBJECT-TYPE SYNTAX SEQUENCE OF SmtpDestEMailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the destination e-mail address. The maximum numbers of destination email address to be added is 5." ::= { smtpMgt 5} smtpDestEMailEntry OBJECT-TYPE SYNTAX SmtpDestEMailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the smtpDestEMailTable." INDEX { smtpDestEMail } ::= { smtpDestEMailTable 1 } SmtpDestEMailEntry ::= SEQUENCE { smtpDestEMail DisplayString, smtpDestEMailStatus ValidStatus } smtpDestEMail OBJECT-TYPE SYNTAX DisplayString (SIZE(0..41)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "SMTP destination e-mail address." ::= { smtpDestEMailEntry 1 } smtpDestEMailStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { smtpDestEMailEntry 2 } -- -- lineMgt -- -- Management for line. This includes management for -- serial line (RS232 port) and Telnet. consoleMgt OBJECT IDENTIFIER ::= { lineMgt 1 } telnetMgt OBJECT IDENTIFIER ::= { lineMgt 2 } vtyMgt OBJECT IDENTIFIER ::= { lineMgt 3 } --consoleMgt consoleDataBits OBJECT-TYPE SYNTAX INTEGER { databits7(1), databits8(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Number of data bits." ::= { consoleMgt 1 } consoleParity OBJECT-TYPE SYNTAX INTEGER { partyNone(1), partyEven(2), partyOdd(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the generation of a parity bit." ::= { consoleMgt 2 } consoleBaudRate OBJECT-TYPE SYNTAX INTEGER { baudRate9600(1), baudRate19200(2), baudRate38400(3), baudRate57600(4), baudRate115200(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Baud rate: Valid values are 115200, 57600, 38400, 19200, and 9600." ::= { consoleMgt 3 } consoleStopBits OBJECT-TYPE SYNTAX INTEGER { stopbits1(1), stopbits2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The console stop bits, valid values are stopbits1(1) or stopbits2(2)" ::= { consoleMgt 4 } consoleExecTimeout OBJECT-TYPE SYNTAX Integer32 (0 | 60..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "In a serial console, use the consoleExecTimeout variable to set the interval that the EXEC command interpreter waits until user input is detected; set the value to 0 to disable it." ::= { consoleMgt 5 } consolePasswordThreshold OBJECT-TYPE SYNTAX Integer32 (0 | 1..120) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of failed console logon attempts that may be made before the system will not accept a further attempt in the time specified by consoleSilentTime. A value of 0 disables the functionality." ::= { consoleMgt 6 } consoleSilentTime OBJECT-TYPE SYNTAX Integer32 (0 | 1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of time that the management console is inaccessible after the number of failed logon attempts has reached consolePasswordThreshold. A value of 0 disables the functionality." ::= { consoleMgt 7 } --to set login timeout seconds consoleLoginResponseTimeout OBJECT-TYPE SYNTAX Integer32(10..300) MAX-ACCESS read-write STATUS current DESCRIPTION "Console login response timeout setting." ::= { consoleMgt 10 } -- telnetMgt telnetStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable the telnet function. Any new telnet request will be rejected and all current telnet sessions will be terminated if this status is set to disabled(2)." DEFVAL { enabled } ::= { telnetMgt 4 } telnetPortNumber OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The telnet session port number." DEFVAL { 23 } ::= { telnetMgt 5 } -- vtyMgt vtyExecTimeout OBJECT-TYPE SYNTAX Integer32 (60..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interval that the system waits for user input before terminating the current session." ::= { vtyMgt 1 } vtyPasswordThreshold OBJECT-TYPE SYNTAX Integer32 (0 | 1..120) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of failed logon attempts that may be made before the system will not accept a further attempt to log on. Setting to 0 means disabled." ::= { vtyMgt 2 } vtyLoginResponseTimeout OBJECT-TYPE SYNTAX Integer32(10..300) MAX-ACCESS read-write STATUS current DESCRIPTION "Login response timeout setting." ::= { vtyMgt 3 } vtyMaxSession OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of allowed sessions." DEFVAL { 8 } ::= { vtyMgt 4 } vtySilentTime OBJECT-TYPE SYNTAX Integer32 (0 | 1..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The time the system waits before etablishing a new session after the number of failed logins reaches the specified limit. Setting to 0 means disabled." ::= { vtyMgt 5 } -- -- sysTimeMgt -- sntpMgt OBJECT IDENTIFIER ::= { sysTimeMgt 1 } ntpMgt OBJECT IDENTIFIER ::= { sysTimeMgt 5 } sntpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable the SNTP, set disabled(2) to disable the SNTP." ::= { sntpMgt 1 } sntpServiceMode OBJECT-TYPE SYNTAX INTEGER { unicast(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Service mode." ::= { sntpMgt 2 } sntpPollInterval OBJECT-TYPE SYNTAX Integer32(16..16384) MAX-ACCESS read-write STATUS current DESCRIPTION "Polling interval." ::= { sntpMgt 3 } sntpServerTable OBJECT-TYPE SYNTAX SEQUENCE OF SntpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for SNTP servers. IP addresses must occupy contiguous indexes, starting from 1. If a removed entry is not the last entry, the table will be shifted to contiguous indexes automatically." ::= { sntpMgt 4 } sntpServerEntry OBJECT-TYPE SYNTAX SntpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for SNTP servers." INDEX { sntpServerIndex } ::= { sntpServerTable 1 } SntpServerEntry ::= SEQUENCE { sntpServerIndex Integer32, sntpServerInetAddressType InetAddressType, sntpServerInetAddress InetAddress, sntpServerStatus ValidStatus } sntpServerIndex OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of a server." ::= { sntpServerEntry 1 } sntpServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the type of address denoted in sntpServerInetAddress type. Only ipv4(1), ipv6(2) and ipv6z(4) types are supported." ::= { sntpServerEntry 4 } sntpServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of a time server." ::= { sntpServerEntry 5 } sntpServerStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { sntpServerEntry 6 } sysCurrentTime OBJECT-TYPE SYNTAX DisplayString(SIZE(20)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' are the first three letters of the English name of the month. '_d' is the day of month. A single-digit day is preceded by a space. 'hh:mm:ss' is a 24-hour representations of hours, minutes, and seconds. A single-digit hour is preceded by a zero. 'yyyy' is a four-digit year. An example is: 'Jan 1 02:03:04 2002'." ::= { sysTimeMgt 2 } sysTimeZone OBJECT-TYPE SYNTAX DisplayString(SIZE(6)) MAX-ACCESS read-write STATUS current DESCRIPTION "This is a text string in the following form: '[s]hh:mm'. '[s]' is a plus-or-minus sign. For UTC, this is omitted. For a positive offset, this is '+'. For a negative offset, this is '-'. 'hh:mm' in the hour and minute offset from UTC. A single-digit hour is preceded by a zero. When sysTimeZonePredefined object is set to any value other than none(1), this object will be empty string." ::= { sysTimeMgt 3 } sysTimeZoneName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the time zone. When sysTimeZonePredefined object is set to any value other than none(1), this object will be empty string." ::= { sysTimeMgt 4 } ntpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable the NTP, set disabled(2) to disable the NTP." ::= { ntpMgt 1 } ntpServiceMode OBJECT-TYPE SYNTAX INTEGER { unicast(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Service mode." ::= { ntpMgt 2 } ntpPollInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Polling interval in seconds." ::= { ntpMgt 3 } ntpAuthenticateStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable the NTP Authenticate, set disabled(2) to disable the NTP." ::= { ntpMgt 4 } ntpServerTable OBJECT-TYPE SYNTAX SEQUENCE OF NtpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for NTP servers" ::= { ntpMgt 5 } ntpServerEntry OBJECT-TYPE SYNTAX NtpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for NTP servers." INDEX { ntpServerIpAddress } ::= { ntpServerTable 1 } NtpServerEntry ::= SEQUENCE { ntpServerIpAddress IpAddress, ntpServerVersion Integer32, ntpServerKeyId Integer32, ntpServerStatus INTEGER } ntpServerIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of a server. Valid IP addresses must occupy contiguous indexes. All IP addresses after the last valid index is 0." ::= { ntpServerEntry 1 } ntpServerVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "NTP version." ::= { ntpServerEntry 2 } ntpServerKeyId OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Key for a NTP server. This variable can only be written." ::= { ntpServerEntry 3 } ntpServerStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { ntpServerEntry 4 } ntpAuthKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF NtpAuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for NTP Authentication keys" ::= { ntpMgt 6 } ntpAuthKeyEntry OBJECT-TYPE SYNTAX NtpAuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for NTP Authentication keys." INDEX { ntpAuthKeyId } ::= { ntpAuthKeyTable 1 } NtpAuthKeyEntry::= SEQUENCE { ntpAuthKeyId Integer32, ntpAuthKeyWord OCTET STRING, ntpAuthKeyStatus INTEGER } ntpAuthKeyId OBJECT-TYPE SYNTAX Integer32 (1..65536) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of a Authentication key. This table has fixed size." ::= { ntpAuthKeyEntry 1 } ntpAuthKeyWord OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Authentication key word is used to created a key by the MD5 And the max length is 32." ::= { ntpAuthKeyEntry 2 } ntpAuthKeyStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { ntpAuthKeyEntry 3 } ntpServerHostTable OBJECT-TYPE SYNTAX SEQUENCE OF NtpServerHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for NTP server host with dns-name." ::= { ntpMgt 7 } ntpServerHostEntry OBJECT-TYPE SYNTAX NtpServerHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for NTP server host with dns-name." INDEX { ntpServerHostAssocId } ::= { ntpServerHostTable 1 } NtpServerHostEntry ::= SEQUENCE { ntpServerHostAssocId Integer32, ntpServerHostInetAddressType InetAddressType, ntpServerHostInetAddress InetAddress, ntpServerHostVersion Integer32, ntpServerHostKeyId Integer32, ntpServerHostStatus INTEGER } ntpServerHostAssocId OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer value greater than 0 that uniquely identifies a NTP server is associated." ::= { ntpServerHostEntry 1 } ntpServerHostInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the type of address denoted in ntpServerHostInetAddress type. Only ipv4(1), dns(16) types are supported." ::= { ntpServerHostEntry 2 } ntpServerHostInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address of a time server." ::= { ntpServerHostEntry 3 } ntpServerHostVersion OBJECT-TYPE SYNTAX Integer32 (3) MAX-ACCESS read-create STATUS current DESCRIPTION "NTP version." ::= { ntpServerHostEntry 4 } ntpServerHostKeyId OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Key for a NTP server. This variable can only be written." ::= { ntpServerHostEntry 5 } ntpServerHostStatus OBJECT-TYPE SYNTAX INTEGER { active(1), create(4), destroy(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has three defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'create', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row." ::= { ntpServerHostEntry 6 } -- -- fileMgt -- -- Management for File System Manipulate, including files copy, display and delete. fileCopyMgt OBJECT IDENTIFIER ::= { fileMgt 1 } fileInfoMgt OBJECT IDENTIFIER ::= { fileMgt 2 } fileAutoUpgradeMgt OBJECT IDENTIFIER ::= { fileMgt 4 } -- -- This performs the copy operation. -- fileCopySrcOperType OBJECT-TYPE SYNTAX INTEGER { file(1), runningCfg(2), startUpCfg(3), tftp(4), unit(5), http(6), ftp(7), sftp(10) } MAX-ACCESS read-write STATUS current DESCRIPTION "fileCopySrcOperType specifies where to copy from, and fileCopyDestOperType specifies where to copy to. Possible combinations of 'fileCopySrcOperType to fileCopyDestOperType' and required parameters are listed in the following table. --------------+------------------+--------------------------------- Source | Destination | Required parameters --------------+------------------+--------------------------------- file(1) | file(1) | fileCopySrcFileName | | fileCopyDestFileName +------------------+--------------------------------- | runningCfg(2) | fileCopySrcFileName +------------------+--------------------------------- | startUpCfg(3) | fileCopySrcFileName | | fileCopyDestFileName +------------------+--------------------------------- | tftp(4) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress +------------------+--------------------------------- | unit(5) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyUnitId +------------------+--------------------------------- | ftp(7) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | sftp(10) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword --------------+------------------+--------------------------------- runningCfg(2) | file(1) | fileCopyDestFileName +------------------+--------------------------------- | startUpCfg(3) | fileCopyDestFileName +------------------+--------------------------------- | tftp(4) | fileCopyDestFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress +------------------+--------------------------------- | ftp(7) | fileCopyDestFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | sftp(10) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword --------------+------------------+--------------------------------- startUpCfg(3) | file(1) | fileCopyDestFileName +------------------+--------------------------------- | runningCfg(2) | None. +------------------+--------------------------------- | tftp(4) | fileCopyDestFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress +------------------+--------------------------------- | ftp(7) | fileCopyDestFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | sftp(10) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword --------------+------------------+--------------------------------- tftp(4) | file(1) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress +------------------+--------------------------------- | runningCfg(2) | fileCopySrcFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress +------------------+--------------------------------- | startUpCfg(3) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress --------------+------------------+--------------------------------- unit(5) | file(1) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyUnitId --------------+------------------+--------------------------------- ftp(7) | file(1) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | runningCfg(2) | fileCopySrcFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | startUpCfg(3) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword --------------+------------------+--------------------------------- sftp(10) | file(1) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyFileType | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | runningCfg(2) | fileCopySrcFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | startUpCfg(3) | fileCopySrcFileName | | fileCopyDestFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword +------------------+--------------------------------- | addRunningCfg(15)| fileCopySrcFileName | | fileCopyServerInetAddressType | | fileCopyServerInetAddress | | fileCopyServerUserName | | fileCopyServerPassword --------------+------------------+---------------------------------" ::= { fileCopyMgt 1} fileCopySrcFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "The source file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to a zero length string when no file name has been specified. Note: If the fileCopySrcOperType is runningCfg(2) or startUpCfg(3), this variable can be ignored." ::= { fileCopyMgt 2 } fileCopyDestOperType OBJECT-TYPE SYNTAX INTEGER { file(1), runningCfg(2), startUpCfg(3), tftp(4), unit(5), http(6), ftp(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "See the description for fileCopySrcOperType." ::= { fileCopyMgt 3 } fileCopyDestFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "The destination file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to a zero length string when no file name has been specified. Note: If the fileCopyDestOperType is runningCfg(2) or startupCfg(3), this variable can be ignored." ::= { fileCopyMgt 4 } fileCopyFileType OBJECT-TYPE SYNTAX INTEGER { opcode(1), config(2), bootRom(3), loader(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of file to copy in fileCopyMgt. opcode(1) indicates operation code, config(2) indicates configuration file, bootRom(3) indicates diagnostic image file and loader(5) indicates loader image file. If the fileCopySrcOperType or fileCopyDestOperType is either runningCfg(2) or startupCfg(3), this variable can be ignored. bootRom(3) and loader(5) can be set only when the fileCopySrcOperType is tftp(4) and fileCopyDestOperType is file(1)." ::= { fileCopyMgt 5 } fileCopyUnitId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the switch unit for stackable devices. When performing the 'copy unit file' or 'copy file unit' action, if neither fileCopySrcOperType nor fileCopyDestOperType is unit(5), this variable can be ignored." ::= { fileCopyMgt 7 } fileCopyAction OBJECT-TYPE SYNTAX INTEGER { notCopying(1), copy(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to copy(2) to begin the copy operation. When the device is not copying, this object will have a value of notCopying(1)." ::= { fileCopyMgt 8 } fileCopyStatus OBJECT-TYPE SYNTAX INTEGER { fileCopyTftpUndefError(1), fileCopyTftpFileNotFound(2), fileCopyTftpAccessViolation(3), fileCopyTftpDiskFull(4), fileCopyTftpIllegalOperation(5), fileCopyTftpUnkownTransferId(6), fileCopyTftpFileExisted(7), fileCopyTftpNoSuchUser(8), fileCopyTftpTimeout(9), fileCopyTftpSendError(10), fileCopyTftpReceiverError(11), fileCopyTftpSocketOpenError(12), fileCopyTftpSocketBindError(13), fileCopyTftpUserCancel(14), fileCopyTftpCompleted(15), fileCopyParaError(16), fileCopyBusy(17), fileCopyUnknown(18), fileCopyReadFileError(19), fileCopySetStartupError(20), fileCopyFileSizeExceed(21), fileCopyMagicWordError(22), fileCopyImageTypeError(23), fileCopyHeaderChecksumError(24), fileCopyImageChecksumError(25), fileCopyWriteFlashFinish(26), fileCopyWriteFlashError(27), fileCopyWriteFlashProgramming(28), fileCopyError(29), fileCopySuccess(30), fileCopyCompleted(31), -- -- ES4612-20-00499, 2008-12-09, support FTPS -- fileCopyFileNotFound(41), fileCopyServerPermissionDenied(42), fileCopyStorageFull(43), fileCopyConnectError(44), fileCopyServerNotInService(45), fileCopyDataConnectionOpenError(46), fileCopyLogInError(47), fileCopyInvalidFileName(48), fileCopyServerNotAcceptProvidedCiphers(49), fileCopyServerNotSupportFtps(50), fileCopyFileUnavailable(51), fileCopyUnclassifiedError(52), fileCopyTimeout(53), fileCopyProjectIdError(54), fileCopyFileNumExceed(55), fileCopySameVersion(56) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the last copy procedure, if any. This object will have a value of fileCopyUnknown(18) if no copy operation has been performed. The listed values are identical to fileAutoDownloadResultStatus." ::= { fileCopyMgt 9 } fileCopyServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Internet address type of the remote server. Only ipv4(1) type is supported." ::= { fileCopyMgt 20 } fileCopyServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Internet address of the remote server." ::= { fileCopyMgt 21 } fileCopyServerUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "Login user name for the remote server. When this variable is empty, the system will use 'anonymous' as user name to log in to the remote server." ::= { fileCopyMgt 22 } fileCopyServerPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "Login password for the remote server. This variable can only be written. When this variable is read, it always returns a zero-length string." ::= { fileCopyMgt 23 } -- -- This mangement performs the display and delete operation. -- fileInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF FileInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contain the information of the file system; we can also perform the delete, set startup file operation." ::= { fileInfoMgt 1 } fileInfoEntry OBJECT-TYPE SYNTAX FileInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptually row for fileInfoTable." INDEX { fileInfoUnitID, IMPLIED fileInfoFileName} ::= { fileInfoTable 1 } FileInfoEntry ::= SEQUENCE { fileInfoUnitID Integer32, fileInfoFileName DisplayString, fileInfoFileType INTEGER, fileInfoIsStartUp TruthValue, fileInfoFileSize Integer32, fileInfoCreationTime DisplayString, fileInfoDelete INTEGER } fileInfoUnitID OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch unit in a stacking system, in a non-stacking system, this value is always 1." ::= { fileInfoEntry 1 } fileInfoFileName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The file Name of the file System in the device." ::= { fileInfoEntry 2 } fileInfoFileType OBJECT-TYPE SYNTAX INTEGER { diag(1), runtime(2), syslog(3), cmdlog(4), config(5), postlog(6), private(7), certificate(8), webarchive(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The file type of the file System in the device." ::= { fileInfoEntry 3 } fileInfoIsStartUp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This flag indicate whether this file is a startup file. Set this object to true(1) to indicate that this is a startup file. Setting this object to false(2) is a invalid operation." ::= { fileInfoEntry 4 } fileInfoFileSize OBJECT-TYPE SYNTAX Integer32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The sizes( in bytes) of the file." ::= { fileInfoEntry 5 } fileInfoCreationTime OBJECT-TYPE SYNTAX DisplayString(SIZE(20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The creation time of the file, This is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' are the first three letters of the English name of the month. '_d' is the day of month. A single-digit day is preceded by a space. 'hh:mm:ss' is a 24-hour representations of hours, minutes, and seconds. A single-digit hour is preceded by a zero. 'yyyy' is the four-digit year. An example is: 'Jan 1 02:03:04 2002'." ::= { fileInfoEntry 6 } fileInfoDelete OBJECT-TYPE SYNTAX INTEGER { noDelete(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Write this object to delete(2) to delete a file, when read, this always return noDelete(1)." ::= { fileInfoEntry 7 } --fileAutoDownloadResultTable fileAutoDownloadResultTable OBJECT-TYPE SYNTAX SEQUENCE OF FileAutoDownloadResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains file auto download result information." ::= { fileMgt 3 } fileAutoDownloadResultEntry OBJECT-TYPE SYNTAX FileAutoDownloadResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for fileAutoDownloadResultTable." INDEX {fileAutoDownloadResultUnitID} ::= { fileAutoDownloadResultTable 1 } FileAutoDownloadResultEntry ::= SEQUENCE { fileAutoDownloadResultUnitID Integer32, fileAutoDownloadResultAction INTEGER, fileAutoDownloadResultStatus INTEGER } fileAutoDownloadResultUnitID OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch unit in a stacking system, in a non-stacking system, this value is always 1." ::= { fileAutoDownloadResultEntry 1 } fileAutoDownloadResultAction OBJECT-TYPE SYNTAX INTEGER { notCopying(1), copying(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the auto download action. value copying(2) will be obtained if the auto download action is currently processing, or value notCopying(1) will be obtained if no auto download action is currently processing. You can check the download result through the fileAutoDownloadResultStatus object after the download action has finished. Please note that this object is read-only, since the auto download action is triggered automatically by the system when an image file or a config file is set as startup setting through the fileInfoIsStartUp, restartOpCodeFile or restartConfigFile objects, but not set by the user manually through this fileAutoDownloadResultAction object." ::= { fileAutoDownloadResultEntry 2 } fileAutoDownloadResultStatus OBJECT-TYPE SYNTAX INTEGER { fileCopyTftpUndefError(1), fileCopyTftpFileNotFound(2), fileCopyTftpAccessViolation(3), fileCopyTftpDiskFull(4), fileCopyTftpIllegalOperation(5), fileCopyTftpUnkownTransferId(6), fileCopyTftpFileExisted(7), fileCopyTftpNoSuchUser(8), fileCopyTftpTimeout(9), fileCopyTftpSendError(10), fileCopyTftpReceiverError(11), fileCopyTftpSocketOpenError(12), fileCopyTftpSocketBindError(13), fileCopyTftpUserCancel(14), fileCopyTftpCompleted(15), fileCopyParaError(16), fileCopyBusy(17), fileCopyUnknown(18), fileCopyReadFileError(19), fileCopySetStartupError(20), fileCopyFileSizeExceed(21), fileCopyMagicWordError(22), fileCopyImageTypeError(23), fileCopyHeaderChecksumError(24), fileCopyImageChecksumError(25), fileCopyWriteFlashFinish(26), fileCopyWriteFlashError(27), fileCopyWriteFlashProgramming(28), fileCopyError(29), fileCopySuccess(30), fileCopyCompleted(31), -- -- ES4612-20-00499, 2008-12-09, support FTPS -- fileCopyFileNotFound(41), fileCopyServerPermissionDenied(42), fileCopyStorageFull(43), fileCopyConnectError(44), fileCopyServerNotInService(45), fileCopyDataConnectionOpenError(46), fileCopyLogInError(47), fileCopyInvalidFileName(48), fileCopyServerNotAcceptProvidedCiphers(49), fileCopyServerNotSupportFtps(50), fileCopyFileUnavailable(51), fileCopyUnclassifiedError(52), fileCopyTimeout(53), fileCopyProjectIdError(54), fileCopyFileNumExceed(55), fileCopySameVersion(56) } MAX-ACCESS read-only STATUS current DESCRIPTION "The last auto download result status. value fileCopyUnknown(18) will be obtained if no download action has been performed before. The listed values are identical to fileCopyStatus." ::= { fileAutoDownloadResultEntry 3 } -- --dnsMgt -- --dnsHostTable dnsDomainLookup OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "To enable the IP Domain Naming System (DNS)-based host name-to-address translation." ::= { dnsMgt 1 } dnsDomainName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "To define a default domain name to complete unqualified host names (names without a dotted-decimal domain name)." ::= { dnsMgt 2 } --dnsCacheTable dnsCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF DnsCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To display the RRs in DNS cache." ::= { dnsMgt 7 } dnsCacheEntry OBJECT-TYPE SYNTAX DnsCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for the dnsCacheTable." INDEX { dnsCacheIndex } ::= { dnsCacheTable 1 } DnsCacheEntry ::= SEQUENCE { dnsCacheIndex Integer32, dnsCacheFlag Integer32, dnsCacheType INTEGER, dnsCacheTtl Integer32, dnsCacheDomain DisplayString, dnsCacheInetAddressType InetAddressType, dnsCacheInetAddress InetAddress } dnsCacheIndex OBJECT-TYPE SYNTAX Integer32(1280..6400) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry sequence number." ::= { dnsCacheEntry 1 } dnsCacheFlag OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Always get 4, means this record is unreliable." ::= { dnsCacheEntry 2 } dnsCacheType OBJECT-TYPE SYNTAX INTEGER { address(1), cname(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cache Type: address(1); cname(2)." ::= { dnsCacheEntry 3 } dnsCacheTtl OBJECT-TYPE SYNTAX Integer32(0..876000) MAX-ACCESS read-only STATUS current DESCRIPTION "The DNS cache TTL." ::= { dnsCacheEntry 5 } dnsCacheDomain OBJECT-TYPE SYNTAX DisplayString(SIZE(1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The DNS cache domain." ::= { dnsCacheEntry 6 } dnsCacheInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of address denoted in dnsHostAddrInetAddress type. Only ipv4(1) and ipv6(2) types are supported." ::= { dnsCacheEntry 7 } dnsCacheInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of DNS cache item." ::= { dnsCacheEntry 8 } dnsHostTable OBJECT-TYPE SYNTAX SEQUENCE OF DnsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of dnsHostEntry. The dnsHostTable and dnsHostAddrTable are used to define static host name-to-address mapping." ::= { dnsMgt 8 } dnsHostEntry OBJECT-TYPE SYNTAX DnsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for the dnsHostTable." INDEX { dnsHostIndex } ::= { dnsHostTable 1 } DnsHostEntry ::= SEQUENCE { dnsHostIndex Integer32, dnsHostName DisplayString, dnsHostStatus ValidStatus } dnsHostIndex OBJECT-TYPE SYNTAX Integer32(1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry sequence number." ::= { dnsHostEntry 1 } dnsHostName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "Host name." ::= { dnsHostEntry 2 } dnsHostStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { dnsHostEntry 3 } --dnsHostAddrTable dnsHostAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF DnsHostAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual table of dnsHostAddrEntry. The dnsHostTable and dnsHostAddrTable are used to define static host name-to-address mapping." ::= { dnsMgt 9 } dnsHostAddrEntry OBJECT-TYPE SYNTAX DnsHostAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for the dnsHostAddrTable." INDEX { dnsHostIndex, dnsHostAddrInetAddressType, IMPLIED dnsHostAddrInetAddress} ::= { dnsHostAddrTable 1 } DnsHostAddrEntry ::= SEQUENCE { dnsHostAddrInetAddressType InetAddressType, dnsHostAddrInetAddress InetAddress, dnsHostAddrStatus ValidStatus } dnsHostAddrInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the type of address denoted in dnsHostAddrInetAddress type. Only ipv4(1), ipv6(2) and ipv6z(4) type are supported." ::= { dnsHostAddrEntry 1 } dnsHostAddrInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the address of the host. Adding one address to two different hosts is not allowed." ::= { dnsHostAddrEntry 2 } dnsHostAddrStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { dnsHostAddrEntry 3 } --dnsDomainListTable dnsDomainListTable OBJECT-TYPE SYNTAX SEQUENCE OF DnsDomainListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines a list of default domain names to complete unqualified host names." ::= { dnsMgt 10 } dnsDomainListEntry OBJECT-TYPE SYNTAX DnsDomainListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for the dnsDomainListTable." INDEX { dnsDomainListIndex } ::= { dnsDomainListTable 1 } DnsDomainListEntry ::= SEQUENCE { dnsDomainListIndex Integer32, dnsDomainListName DisplayString, dnsDomainListStatus ValidStatus } dnsDomainListIndex OBJECT-TYPE SYNTAX Integer32(1..3) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry sequence number." ::= { dnsDomainListEntry 1 } dnsDomainListName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "Domain name." ::= { dnsDomainListEntry 2 } dnsDomainListStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { dnsDomainListEntry 3 } dnsNameServerInetTable OBJECT-TYPE SYNTAX SEQUENCE OF DnsNameServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the address of one or more name servers to use for name and address resolution." ::= { dnsMgt 11 } dnsNameServerInetEntry OBJECT-TYPE SYNTAX DnsNameServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row for dnsNameServerInetTable." INDEX { dnsNameServerInetAddressType, IMPLIED dnsNameServerInetAddress } ::= { dnsNameServerInetTable 1 } DnsNameServerInetEntry ::= SEQUENCE { dnsNameServerInetAddressType InetAddressType, dnsNameServerInetAddress InetAddress, dnsNameServerInetStatus ValidStatus } dnsNameServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Type of address. Only ipv4(1), ipv6(2) and ipv6z(4) types are supported." ::= { dnsNameServerInetEntry 1 } dnsNameServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address of name server." ::= { dnsNameServerInetEntry 2 } dnsNameServerInetStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { dnsNameServerInetEntry 3 } -- -- poeMgt -- -- PSE Objects pethPseMainExtTable OBJECT-TYPE SYNTAX SEQUENCE OF PethPseMainExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects that display and control attributes of the main power source in a PSE device. Ethernet switches are one example of boxes that would support these objects. Values of all read-write objects in this table are persistent at restart/reboot." REFERENCE "IEEE 802.3af, POWER-ETHERNET-MIB.pethMainPseTable" ::= { poeMgt 5 } pethPseMainExtEntry OBJECT-TYPE SYNTAX PethPseMainExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of objects that display and control the Main power of a PSE." AUGMENTS { pethMainPseEntry } ::= { pethPseMainExtTable 1 } PethPseMainExtEntry ::= SEQUENCE { pethPseMainExtDllPowerType INTEGER, pethPseMainExtDllPowerSource INTEGER } pethPseMainExtDllPowerType OBJECT-TYPE SYNTAX INTEGER { type2Pse(0), type1Pse(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the local system is a PSE or a PD and whether it is Type 1 or Type 2." REFERENCE "IEEE Std 802.3at Section 30.9.1.1.12 aDLLPowerType" ::= { pethPseMainExtEntry 1 } pethPseMainExtDllPowerSource OBJECT-TYPE SYNTAX INTEGER { unknown(0), primary(1), backup(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The power sources of the local system." REFERENCE "IEEE Std 802.3at Section 30.9.1.1.14 aDLLPowerSource" ::= { pethPseMainExtEntry 2 } pethPsePortExtTable OBJECT-TYPE SYNTAX SEQUENCE OF PethPsePortExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects that display and control the power characteristics of power Ethernet ports on a Power Source Entity (PSE) device. This group will be implemented in managed power Ethernet switches and mid-span devices. Values of all read-write objects in this table are persistent at restart/reboot." REFERENCE "IEEE 802.3af, POWER-ETHERNET-MIB.pethPsePortTable" ::= { poeMgt 6 } pethPsePortExtEntry OBJECT-TYPE SYNTAX PethPsePortExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of objects that display and control the power characteristics of a power Ethernet PSE port." AUGMENTS { pethPsePortEntry } ::= { pethPsePortExtTable 1 } PethPsePortExtEntry ::= SEQUENCE { pethPsePortExtMirroredDllPdRequestedPowerValue INTEGER, pethPsePortExtDllPseAllocatedPowerValue INTEGER, pethPsePortTimeRange DisplayString, pethPsePortTimeRangeStatus INTEGER, pethPsePortExtMaximumPowerValue INTEGER, pethPsePortExtUsedPowerValue INTEGER } pethPsePortExtMirroredDllPdRequestedPowerValue OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the PD requested power value received from the remote system. The definition and encoding of PD requested power value is the same as described in pethPdPortDllPdRequestedPowerValue." REFERENCE "IEEE Std 802.3at Section 30.9.1.1.18 aMirroredDLLPDRequestedPowerValue" ::= { pethPsePortExtEntry 4 } pethPsePortExtDllPseAllocatedPowerValue OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the PSE allocated power value that the local system has currently allocated to the remote system. The PSE allocated power value is the maximum input average power that the PSE wants the PD to ever draw under this allocation if it is accepted. The PSE allocated power value is encoded according to Equation (33-20), where X is the decimal value of pethPsePortExtDllPseAllocatedPowerValue." REFERENCE "IEEE Std 802.3at Section 30.9.1.1.20 aDLLPSEAllocatedPowerValue" ::= { pethPsePortExtEntry 6 } pethPsePortTimeRange OBJECT-TYPE SYNTAX DisplayString(SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the time range entry bound to the port. This object should be equal to one of the timeRangeName objects in timeRangeTable. The object works when pethPsePortAdminEnable is enabled(1)." ::= { pethPsePortExtEntry 11 } pethPsePortTimeRangeStatus OBJECT-TYPE SYNTAX INTEGER { none(0), active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "If no time range entry is bound to the port, value of this object is none(0). If PoE time range of the port is active, value of this object is active(1). If PoE time range of the port is inactive, value of this object is inactive(2)." ::= { pethPsePortExtEntry 12 } pethPsePortExtMaximumPowerValue OBJECT-TYPE SYNTAX INTEGER UNITS "milliwatts" MAX-ACCESS read-write STATUS current DESCRIPTION "Returns the user-configurable maximum power value that the local system has currently allocated to the remote system. The units of this variable is milliwatts." ::= { pethPsePortExtEntry 13 } pethPsePortExtUsedPowerValue OBJECT-TYPE SYNTAX INTEGER UNITS "milliwatts" MAX-ACCESS read-only STATUS current DESCRIPTION "Returns the currently used power value that the local system is delivering to the remote system. The units of this variable is milliwatts." ::= { pethPsePortExtEntry 14 } -- -- This mangement automatically upgrades image. -- fileAutoUpgradeOpCodeStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set this variable to enabled(1) to enable the device to automatically upgrade the current software image when a new version is detected. Set this variable to disabled(2) to disable this feature." ::= { fileAutoUpgradeMgt 1 } fileAutoUpgradeOpCodePath OBJECT-TYPE SYNTAX DisplayString(SIZE(0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "The URL (Universal Resource Location) of the image file location for automatic upgrades. The URL schema can be set to TFTP. The Hostname is the IP address of the server. The last character of the URL is always a '/' and the filename must not be included in the URL." ::= { fileAutoUpgradeMgt 2 } fileAutoUpgradeOpCodeFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The file name of the image file." ::= { fileAutoUpgradeMgt 3 } -- -- mcastStormMgt -- mcastStormMgt OBJECT IDENTIFIER ::= { stormMgt 1 } mcastStormTable OBJECT-TYPE SYNTAX SEQUENCE OF McastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table to manage the control of multicast storms for ports." ::= { mcastStormMgt 1 } mcastStormEntry OBJECT-TYPE SYNTAX McastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of multiStormTable." INDEX { mcastStormIfIndex } ::= { mcastStormTable 1 } McastStormEntry ::= SEQUENCE { mcastStormIfIndex InterfaceIndex, mcastStormStatus EnabledStatus, mcastStormPktRate Integer32 } mcastStormIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mcastStormEntry 1 } mcastStormStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether multicast storm protection is enabled." ::= { mcastStormEntry 2 } mcastStormPktRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Multicast storm threshold as packets per second. If this entry is for a trunk, this is the value for each member port. The range is 500 to 14881000." ::= { mcastStormEntry 4 } -- -- bcastStormMgt -- -- Management for broadcast storm control for ports. bcastStormMgt OBJECT IDENTIFIER ::= { stormMgt 3 } bcastStormTable OBJECT-TYPE SYNTAX SEQUENCE OF BcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table to manage the control of broadcast storms for ports." ::= { bcastStormMgt 1 } bcastStormEntry OBJECT-TYPE SYNTAX BcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of bcastStormTable." INDEX { bcastStormIfIndex } ::= { bcastStormTable 1 } BcastStormEntry ::= SEQUENCE { bcastStormIfIndex InterfaceIndex, bcastStormStatus EnabledStatus, bcastStormPktRate Integer32 } bcastStormIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { bcastStormEntry 1 } bcastStormStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether broadcast storm protection is enabled." ::= { bcastStormEntry 2 } bcastStormPktRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Broadcast storm threshold as packets per second. If this entry is for a trunk, this is the value for each member port. The range is 500 to 14881000." ::= { bcastStormEntry 4 } -- -- unknownUcastStormMgt -- unknownUcastStormMgt OBJECT IDENTIFIER ::= {stormMgt 4 } unknownUcastStormTable OBJECT-TYPE SYNTAX SEQUENCE OF UnknownUcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table to manage the unknown unicast storm control." ::= { unknownUcastStormMgt 1 } unknownUcastStormEntry OBJECT-TYPE SYNTAX UnknownUcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of unknownUcastStormTable." INDEX { unknownUcastStormIfIndex } ::= { unknownUcastStormTable 1 } UnknownUcastStormEntry ::= SEQUENCE { unknownUcastStormIfIndex InterfaceIndex, unknownUcastStormStatus EnabledStatus, unknownUcastStormPktRate Integer32 } unknownUcastStormIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port or trunk interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { unknownUcastStormEntry 1 } unknownUcastStormStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates that the unknown unicast storm protection is enabled/disabled." ::= { unknownUcastStormEntry 2 } unknownUcastStormPktRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the packet rate(packet per second) of the storm protection. The range is 500 to 14881000." ::= { unknownUcastStormEntry 4 } -- -- Auto Traffic Control -- atcMgt OBJECT IDENTIFIER ::= { stormMgt 5 } atcBcastStormTcApplyTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the timing when the ATC (Auto Traffic Control) is activated after the broadcast traffic being detected as the storm." ::= { atcMgt 1 } atcBcastStormTcReleaseTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the timing when the ATC is released after the broadcast traffic being detected as no storm." ::= { atcMgt 2 } atcBcastStormTable OBJECT-TYPE SYNTAX SEQUENCE OF AtcBcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains the Auto Traffic Control configuration and the status for broadcast traffic." ::= { atcMgt 3 } atcBcastStormEntry OBJECT-TYPE SYNTAX AtcBcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of the table." INDEX { atcBcastStormIfIndex } ::= { atcBcastStormTable 1 } AtcBcastStormEntry ::= SEQUENCE { atcBcastStormIfIndex InterfaceIndex, atcBcastStormEnable EnabledStatus, atcBcastStormAutoRelease EnabledStatus, atcBcastStormSampleType INTEGER, atcBcastStormCurrentTrafficRate Integer32, atcBcastStormAlarmFireThreshold Integer32, atcBcastStormAlarmClearThreshold Integer32, atcBcastStormTcAction INTEGER, atcBcastStormAlarmFireTrapStatus EnabledStatus, atcBcastStormAlarmClearTrapStatus EnabledStatus, atcBcastStormTcApplyTrapStatus EnabledStatus, atcBcastStormTcReleaseTrapStatus EnabledStatus } atcBcastStormIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The specified port on which the ATC is applied." ::= { atcBcastStormEntry 1 } atcBcastStormEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the ATC of the broadcast traffic is applied." ::= { atcBcastStormEntry 2 } atcBcastStormAutoRelease OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the Auto-Release feature of ATC is applied." ::= { atcBcastStormEntry 3 } atcBcastStormSampleType OBJECT-TYPE SYNTAX INTEGER { packet-rate(1), octet-rate(2), percent(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the unit of traffic rate and threshold." ::= { atcBcastStormEntry 4 } atcBcastStormCurrentTrafficRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The parameter indicates the current broadcast traffic rate." ::= { atcBcastStormEntry 5 } atcBcastStormAlarmFireThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates that if the current broadcast traffic rate exceeds the specified threshold, it will be treated as the storm." ::= { atcBcastStormEntry 6 } atcBcastStormAlarmClearThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates that if the current broadcast traffic falls below the specified threshold it will be treated as the normal traffic." ::= { atcBcastStormEntry 7 } atcBcastStormTcAction OBJECT-TYPE SYNTAX INTEGER { rate-control(1), shutdown(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the protecting action which ATC will applied to the specified port." ::= { atcBcastStormEntry 8 } atcBcastStormAlarmFireTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the broadcast storm has been detected." ::= { atcBcastStormEntry 9 } atcBcastStormAlarmClearTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the broadcast storm has been detected as the normal traffic." ::= { atcBcastStormEntry 10 } atcBcastStormTcApplyTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the ATC is activated." ::= { atcBcastStormEntry 11 } atcBcastStormTcReleaseTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the ATC is released." ::= { atcBcastStormEntry 12 } atcMcastStormTcApplyTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the timing when the ATC (Auto Traffic Control) is activated after the broadcast traffic being detected as the storm." ::= { atcMgt 4 } atcMcastStormTcReleaseTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the timing when the ATC is released after the broadcast traffic being detected as no storm." ::= { atcMgt 5 } atcMcastStormTable OBJECT-TYPE SYNTAX SEQUENCE OF AtcMcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains the Auto Traffic Control configuration and the status for mulicast traffic." ::= { atcMgt 6 } atcMcastStormEntry OBJECT-TYPE SYNTAX AtcMcastStormEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The conceptual row of the table." INDEX { atcMcastStormIfIndex } ::= { atcMcastStormTable 1 } AtcMcastStormEntry ::= SEQUENCE { atcMcastStormIfIndex InterfaceIndex, atcMcastStormEnable EnabledStatus, atcMcastStormAutoRelease EnabledStatus, atcMcastStormSampleType INTEGER, atcMcastStormCurrentTrafficRate Integer32, atcMcastStormAlarmFireThreshold Integer32, atcMcastStormAlarmClearThreshold Integer32, atcMcastStormTcAction INTEGER, atcMcastStormAlarmFireTrapStatus EnabledStatus, atcMcastStormAlarmClearTrapStatus EnabledStatus, atcMcastStormTcApplyTrapStatus EnabledStatus, atcMcastStormTcReleaseTrapStatus EnabledStatus } atcMcastStormIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The specified port on which the ATC is applied." ::= { atcMcastStormEntry 1 } atcMcastStormEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the ATC of the mulicast traffic is applied." ::= { atcMcastStormEntry 2 } atcMcastStormAutoRelease OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the Auto-Release feature of ATC is applied." ::= { atcMcastStormEntry 3 } atcMcastStormSampleType OBJECT-TYPE SYNTAX INTEGER { packet-rate(1), octet-rate(2), percent(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the unit of traffic rate and threshold." ::= { atcMcastStormEntry 4 } atcMcastStormCurrentTrafficRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The parameter indicates the current mulicast traffic rate." ::= { atcMcastStormEntry 5 } atcMcastStormAlarmFireThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates that if the current mulicast traffic rate exceeds the specified threshold, it will be treated as the storm." ::= { atcMcastStormEntry 6 } atcMcastStormAlarmClearThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates that if the current mulicast traffic falls below the specified threshold it will be treated as the normal traffic." ::= { atcMcastStormEntry 7 } atcMcastStormTcAction OBJECT-TYPE SYNTAX INTEGER { rate-control(1), shutdown(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the protecting action which ATC will applied to the specified port." ::= { atcMcastStormEntry 8 } atcMcastStormAlarmFireTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the mulicast storm has been detected." ::= { atcMcastStormEntry 9 } atcMcastStormAlarmClearTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the mulicast storm has been detected as the normal traffic." ::= { atcMcastStormEntry 10 } atcMcastStormTcApplyTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the ATC is activated." ::= { atcMcastStormEntry 11 } atcMcastStormTcReleaseTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates whether the trap has to be sent when the ATC is released." ::= { atcMcastStormEntry 12 } -- stormMgtGlobalSampleType stormMgtGlobalSampleType OBJECT-TYPE SYNTAX INTEGER { packet-rate(1), percent(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter indicates the unit of traffic rate for storm control." ::= { stormMgt 7 } -- -- sysResourceMgt -- -- monitor the configuration changes for the product cpuStatus OBJECT IDENTIFIER ::= { sysResourceMgt 2 } memoryStatus OBJECT IDENTIFIER ::= { sysResourceMgt 3 } -- cpuStatus cpuCurrentUti OBJECT-TYPE SYNTAX Integer32 (1..100) UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "The current CPU utilization in percent in the past 5 seconds." ::= { cpuStatus 1 } cpuStatMaxUti OBJECT-TYPE SYNTAX Integer32 (1..100) UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum CPU utilization in percent in the past 60 seconds." ::= { cpuStatus 2 } cpuStatAvgUti OBJECT-TYPE SYNTAX Integer32 (1..100) UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "The average CPU utilization in percent in the past 60 seconds." ::= { cpuStatus 3 } cpuPeakTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the CPU utilization reaches cpuUtiRisingThreshold in the format of 'Mmm _d hh:mm:ss yyyy' as defined in sysCurrentTime of this MIB." ::= { cpuStatus 4 } cpuPeakDuration OBJECT-TYPE SYNTAX Integer32 UNITS "second" MAX-ACCESS read-only STATUS current DESCRIPTION "The duration from the CPU utilization reaches cpuUtiRisingThreshold to reaches cpuUtiFallingThreshold, in seconds." ::= { cpuStatus 5 } cpuUtiRisingThreshold OBJECT-TYPE SYNTAX Integer32 (1..100) UNITS "%" MAX-ACCESS read-write STATUS current DESCRIPTION "The rising threshold of the cpu utilization." ::= { cpuStatus 6 } cpuUtiFallingThreshold OBJECT-TYPE SYNTAX Integer32 (1..100) UNITS "%" MAX-ACCESS read-write STATUS current DESCRIPTION "The falling threshold of the cpu utilization." ::= { cpuStatus 7 } -- memoryStatus memoryTotal OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total amount of the memory in kilobytes." ::= { memoryStatus 1 } memoryAllocated OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of the memory allocated in kilobytes." ::= { memoryStatus 2 } memoryFreed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of the free memory in kilobytes." ::= { memoryStatus 3} memoryFreedInPercent OBJECT-TYPE SYNTAX Integer32 (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "the memory freed in proportion to the total memory." ::= { memoryStatus 4 } memoryUtiRisingThreshold OBJECT-TYPE SYNTAX Integer32 (1..100) UNITS "%" MAX-ACCESS read-write STATUS current DESCRIPTION "The rising threshold of the memory utilization." ::= { memoryStatus 5 } memoryUtiFallingThreshold OBJECT-TYPE SYNTAX Integer32 (1..100) UNITS "%" MAX-ACCESS read-write STATUS current DESCRIPTION "The falling threshold of the memory utilization." ::= { memoryStatus 6 } -- taskCpuTable taskCpuTable OBJECT-TYPE SYNTAX SEQUENCE OF TaskCpuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and status information describing the CPU utilization of each task." ::= { sysResourceMgt 4 } taskCpuEntry OBJECT-TYPE SYNTAX TaskCpuEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, describing the CPU utilization of one task." INDEX { taskCpuName } ::= { taskCpuTable 1 } TaskCpuEntry ::= SEQUENCE { taskCpuName DisplayString, taskCpuCurrentUti Integer32, taskCpuStatMaxUti Integer32, taskCpuStatAvgUti Integer32 } taskCpuName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the task." ::= { taskCpuEntry 1 } taskCpuCurrentUti OBJECT-TYPE SYNTAX Integer32 (1..10000) MAX-ACCESS read-only STATUS current DESCRIPTION "The current CPU utilization in hundredths of a percent in the past 5 seconds." ::= { taskCpuEntry 2 } taskCpuStatMaxUti OBJECT-TYPE SYNTAX Integer32 (1..10000) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum CPU utilization in hundredths of a percent in the past 60 seconds." ::= { taskCpuEntry 3 } taskCpuStatAvgUti OBJECT-TYPE SYNTAX Integer32 (1..10000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average CPU utilization in hundredths of a percent in the past 60 seconds." ::= { taskCpuEntry 4 } -- cpuGuard cpuGuard OBJECT IDENTIFIER ::= { sysResourceMgt 5 } cpuGuardStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU guard status." ::= { cpuGuard 1 } cpuGuardHighWatermark OBJECT-TYPE SYNTAX Integer32 (20..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU guard high-watermark." ::= { cpuGuard 2 } cpuGuardLowWatermark OBJECT-TYPE SYNTAX Integer32 (20..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU guard low-watermark." ::= { cpuGuard 3 } cpuGuardMaxThreshold OBJECT-TYPE SYNTAX Integer32 (50..500) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU guard maximum threshold." ::= { cpuGuard 4 } cpuGuardMinThreshold OBJECT-TYPE SYNTAX Integer32 (50..500) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU guard minimum threshold." ::= { cpuGuard 5 } cpuGuardTrapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU guard trap status." ::= { cpuGuard 6 } cpuGuardCurrentThreshold OBJECT-TYPE SYNTAX Integer32 (50..500) MAX-ACCESS read-only STATUS current DESCRIPTION "The current CPU guard threshold." ::= { cpuGuard 7 } -- --mvrMgt -- mvrForwardingPriority OBJECT-TYPE SYNTAX Integer32(0..7|65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure MVR multicast stream forwarding priority. If value is 65535, it means the priority is disabled." ::= { mvrMgt 18 } mvrDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the MVR port." ::= { mvrMgt 20 } mvrDomainEntry OBJECT-TYPE SYNTAX MvrDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR Domain." INDEX {mvrDomainId} ::= { mvrDomainTable 1 } MvrDomainEntry ::= SEQUENCE { mvrDomainId Integer32, mvrDomainStatus EnabledStatus, mvrDomainRunningStatus INTEGER, mvrDomainVlanId VlanIndex, mvrDomainUpstreamSourceIp IpAddress, mvrDomainClearDynamicGroups TruthValue } mvrDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Speicfies which MVR domain to configure." ::= { mvrDomainEntry 1 } mvrDomainStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable MVR(Multicast VLAN Registration) on the device." ::= { mvrDomainEntry 2} mvrDomainRunningStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Describes the running status of MVR (Multicast VLAN Registration) to the switch. A value of active(1) indicates that all necessary conditions in the MVR environment are satisfied. A value of inactive(2) indicates that some necessary conditions in the MVR environment are not satisfied." ::= { mvrDomainEntry 3} mvrDomainVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "To set VLAN for MVR.The VLAN identified by a particular value of this index is the same VLAN as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB." ::= { mvrDomainEntry 4 } mvrDomainUpstreamSourceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Set the source IP address which MVR will carry in IP header when send IGMP packet to upstream router through MVR source port." ::= { mvrDomainEntry 5 } mvrDomainClearDynamicGroups OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear dynamic learned groups" ::= { mvrDomainEntry 6} mvrDomainPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrDomainPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the MVR port." ::= { mvrMgt 21 } mvrDomainPortEntry OBJECT-TYPE SYNTAX MvrDomainPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR port." INDEX { mvrPortDomainId, mvrDomainIfIndex } ::= { mvrDomainPortTable 1 } MvrDomainPortEntry ::= SEQUENCE { mvrPortDomainId Integer32, mvrDomainIfIndex InterfaceIndex, mvrDomainPortType INTEGER, mvrDomainPortImmediateLeave EnabledStatus, mvrDomainPortActive INTEGER, mvrDomainPortImmediateLeaveByHostIp EnabledStatus } mvrPortDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Speicfies which MVR domain to configure." ::= { mvrDomainPortEntry 1 } mvrDomainIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mvrDomainPortEntry 2 } mvrDomainPortType OBJECT-TYPE SYNTAX INTEGER { none(0), source(1), receiver(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "For configuring the MVR port type. To disable the MVR port type, use the none(0)." ::= { mvrDomainPortEntry 3 } mvrDomainPortImmediateLeave OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "To enable immediate leave on MVR port." ::= { mvrDomainPortEntry 4 } mvrDomainPortActive OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "To indicate if the port is associated with the MVR group. If the port is the MVR receiver port or the MVR source port in MVR vlan, the status is active(1); otherwise the status is inactive(2)." ::= { mvrDomainPortEntry 5 } mvrDomainPortImmediateLeaveByHostIp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "To enable immediate leave by host IP on MVR port." ::= { mvrDomainPortEntry 6 } mvrProfileTable OBJECT IDENTIFIER ::= {mvrMgt 22 } mvrProfileCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrProfileCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR profile." ::= { mvrProfileTable 1 } MvrProfileCtlEntry ::= SEQUENCE { mvrProfileCtlId Integer32, mvrProfileName OCTET STRING, mvrProfileCtlAction INTEGER } mvrProfileCtlEntry OBJECT-TYPE SYNTAX MvrProfileCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR profile." INDEX {mvrProfileCtlId} ::= { mvrProfileCtlTable 1 } mvrProfileCtlId OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvrProfileCtlEntry 1 } mvrProfileName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "MVR Profile name which identify a group range. NOTE: All mvrProfileCtlEntry use the same buffer to temply store the mvrProfileName before mvrProfileCtlAction really creat the profile." ::= { mvrProfileCtlEntry 2 } mvrProfileCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(0), create(1), destory(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to create(2) to create profile. Set this object to destory(3) to delete profile. When the action is complete, this object becomes noAction(1)." ::= { mvrProfileCtlEntry 5 } mvrProfileGroupCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrProfileGroupCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR group ranges for MVR profile." ::= { mvrProfileTable 2 } MvrProfileGroupCtlEntry ::= SEQUENCE { mvrProfileGropuCtlProfileId Integer32, mvrProfileGroupCtlId Integer32, mvrProfileGroupStartIPAddress IpAddress, mvrProfileGroupEndIPAddress IpAddress, mvrProfileGroupCtlAction INTEGER } mvrProfileGroupCtlEntry OBJECT-TYPE SYNTAX MvrProfileGroupCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the group ranges on MVR profile." INDEX {mvrProfileGropuCtlProfileId, mvrProfileGroupCtlId} ::= { mvrProfileGroupCtlTable 1 } mvrProfileGropuCtlProfileId OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= {mvrProfileGroupCtlEntry 1} mvrProfileGroupCtlId OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which group range in MVR profile" ::= { mvrProfileGroupCtlEntry 2 } mvrProfileGroupStartIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MVR Profile range start IP address. NOTE: All mvrProfileGroupCtlEntry use the same buffer to temply store the mvrProfileStartIPAddress before mvrProfileGroupCtlAction really creat the group rang on profile." ::= { mvrProfileGroupCtlEntry 3} mvrProfileGroupEndIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MVR Profile range end IP address. NOTE: All mvrProfileGroupCtlEntry use the same buffer to temply store the mvrProfileEndIPAddress before mvrProfileGroupCtlAction really creat the group rang on profile." ::= { mvrProfileGroupCtlEntry 4 } mvrProfileGroupCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(0), create(1), destory(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to create(2) to create group range. Set this object to destory(3) to delete group range. When the action is complete, this object becomes noAction(1). NOTE: If mvrProfileGroupStartIPAddress and mvrProfileGroupEndIPAddress pattern already exist on other mvrProfileGroupCtlId, it won't be stored. " ::= { mvrProfileGroupCtlEntry 5 } mvrDomainAssociatedProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrDomainAssociatedProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configure MVR domain associate which MVR profile" ::= {mvrMgt 23 } mvrDomainAssociatedProfileEntry OBJECT-TYPE SYNTAX MvrDomainAssociatedProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring MVR domain associate MVR profile." INDEX { mvrProfileDomainId, mvrProfileId } ::= { mvrDomainAssociatedProfileTable 1 } MvrDomainAssociatedProfileEntry ::= SEQUENCE { mvrProfileDomainId Integer32, mvrProfileId Integer32, mvrProfileAction INTEGER } mvrProfileDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvrDomainAssociatedProfileEntry 1 } mvrProfileId OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvrDomainAssociatedProfileEntry 2 } mvrProfileAction OBJECT-TYPE SYNTAX INTEGER { noAction(0), create(1), destory(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to create(1) to associate profile. Set this object to destory(2) to deassociate profile. When the action is complete, this object becomes noAction(0)." ::= { mvrDomainAssociatedProfileEntry 3 } mvrDomainGroupStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrDomainGroupStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the static members of the MVR group." ::= { mvrMgt 24 } mvrDomainGroupStaticEntry OBJECT-TYPE SYNTAX MvrDomainGroupStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the static members of the MVR group." INDEX { mvrGroupStaticDomainId, mvrDomainGroupStaticAddress, mvrDomainGroupStaticReceiverVlan} ::= { mvrDomainGroupStaticTable 1 } MvrDomainGroupStaticEntry ::= SEQUENCE { mvrGroupStaticDomainId Integer32, mvrDomainGroupStaticAddress IpAddress, mvrDomainGroupStaticReceiverVlan Integer32, mvrDomainGroupStaticPorts PortList } mvrGroupStaticDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvrDomainGroupStaticEntry 1 } mvrDomainGroupStaticAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast address of the MVR group." ::= { mvrDomainGroupStaticEntry 2 } mvrDomainGroupStaticReceiverVlan OBJECT-TYPE SYNTAX Integer32(1..4093) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The receiver vlan of this MVR group" ::= { mvrDomainGroupStaticEntry 3 } mvrDomainGroupStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports configured by management in this entry. Ports entered in this list will be the static members of this MVR group." ::= { mvrDomainGroupStaticEntry 4 } mvrDomainGroupCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrDomainGroupCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for the current members of the MVR group." ::= { mvrMgt 25 } mvrDomainGroupCurrentEntry OBJECT-TYPE SYNTAX MvrDomainGroupCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for the current members of the MVR group." INDEX { mvrGroupCurrenDomainId, mvrDomainGroupCurrentAddress, mvrDomainGroupCurrentReceiverVlan } ::= { mvrDomainGroupCurrentTable 1 } MvrDomainGroupCurrentEntry ::= SEQUENCE { mvrGroupCurrenDomainId Integer32, mvrDomainGroupCurrentAddress IpAddress, mvrDomainGroupCurrentReceiverVlan Integer32, mvrDomainGroupCurrentPorts PortList } mvrGroupCurrenDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvrDomainGroupCurrentEntry 1 } mvrDomainGroupCurrentAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast address of the MVR group." ::= { mvrDomainGroupCurrentEntry 2 } mvrDomainGroupCurrentReceiverVlan OBJECT-TYPE SYNTAX Integer32(1..4093) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the receiver VLAN of the MVR group." ::= { mvrDomainGroupCurrentEntry 3 } mvrDomainGroupCurrentPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The complete set of ports currently associated with this MVR group." ::= { mvrDomainGroupCurrentEntry 4 } mvrProxySwitching OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable MVR(Multicast VLAN Registration) proxy switching ability on the device. " ::= { mvrMgt 27 } mvrRobustnessValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Paremete to set IGMP robustness value. This value apply to proxy-switching for how many IGMP report/leave will be send out from source port, and how many g-s query will be send on receiver port. " ::= { mvrMgt 28 } mvrProxyQueryInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the query interval that active receiver port will use to send out general query " ::= { mvrMgt 29 } mvrSourcePortmode OBJECT-TYPE SYNTAX INTEGER { dynamic(1), forward(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Paremete to set MVR Source Port forward mode. When set dynamic, MVR source port won't forward multicast streams received from other source port. When set forward, MVR source port will forward multicast streams received from other source port. These multicast stream all are in MVR group range. " ::= { mvrMgt 30 } mvrPortStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrPortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of service per port." ::= {mvrMgt 32 } mvrPortStatisticsEntry OBJECT-TYPE SYNTAX MvrPortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of service per port." INDEX { mvrPortStatisticsDomainId, mvrPortStatisticsPortIndex } ::= {mvrPortStatisticsTable 1} MvrPortStatisticsEntry ::= SEQUENCE { mvrPortStatisticsDomainId Integer32, mvrPortStatisticsPortIndex InterfaceIndex, mvrPortStatisticsNumGroups Unsigned32, mvrPortStatisticsNumJoinSend Unsigned32, mvrPortStatisticsNumJoins Unsigned32, mvrPortStatisticsNumJoinSuccess Unsigned32, mvrPortStatisticsNumLeavesSend Unsigned32, mvrPortStatisticsNumLeaves Unsigned32, mvrPortStatisticsNumGeneralQuerySend Unsigned32, mvrPortStatisticsNumGeneralQueryRecevied Unsigned32, mvrPortStatisticsNumSepcificQuerySend Unsigned32, mvrPortStatisticsNumSpecificQueryReceived Unsigned32, mvrPortStatisticsNumInvalidReport Unsigned32, mvrPortStatisticsClearStatistics TruthValue } mvrPortStatisticsDomainId OBJECT-TYPE SYNTAX Integer32(1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "MVR domain ID." ::= { mvrPortStatisticsEntry 1 } mvrPortStatisticsPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the mvrPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mvrPortStatisticsEntry 2 } mvrPortStatisticsNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { mvrPortStatisticsEntry 3 } mvrPortStatisticsNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send " ::= { mvrPortStatisticsEntry 4 } mvrPortStatisticsNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join recieved " ::= { mvrPortStatisticsEntry 5 } mvrPortStatisticsNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join group success " ::= { mvrPortStatisticsEntry 6 } mvrPortStatisticsNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send" ::= { mvrPortStatisticsEntry 7 } mvrPortStatisticsNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { mvrPortStatisticsEntry 8} mvrPortStatisticsNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send. " ::= { mvrPortStatisticsEntry 9} mvrPortStatisticsNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received. " ::= { mvrPortStatisticsEntry 10} mvrPortStatisticsNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send. " ::= { mvrPortStatisticsEntry 11} mvrPortStatisticsNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query received. " ::= { mvrPortStatisticsEntry 12} mvrPortStatisticsNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received. " ::= { mvrPortStatisticsEntry 13} mvrPortStatisticsClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN all statistics " ::= { mvrPortStatisticsEntry 14} mvrVlanStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF MvrVlanStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Mvr statistics VLAN." ::= {mvrMgt 33 } mvrVlanStatisticsEntry OBJECT-TYPE SYNTAX MvrVlanStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of Mvr statistics VLAN." INDEX { mvrVlanStatisticsDomainId, mvrVlanStatisticsVlanId } ::= {mvrVlanStatisticsTable 1} MvrVlanStatisticsEntry ::= SEQUENCE { mvrVlanStatisticsDomainId Integer32, mvrVlanStatisticsVlanId VlanIndex, mvrVlanStatisticsNumGroups Unsigned32, mvrVlanStatisticsNumJoinSend Unsigned32, mvrVlanStatisticsNumJoins Unsigned32, mvrVlanStatisticsNumJoinSuccess Unsigned32, mvrVlanStatisticsNumLeavesSend Unsigned32, mvrVlanStatisticsNumLeaves Unsigned32, mvrVlanStatisticsNumGeneralQuerySend Unsigned32, mvrVlanStatisticsNumGeneralQueryRecevied Unsigned32, mvrVlanStatisticsNumSepcificQuerySend Unsigned32, mvrVlanStatisticsNumSpecificQueryReceived Unsigned32, mvrVlanStatisticsNumInvalidReport Unsigned32, mvrVlanStatisticsClearStatistics TruthValue } mvrVlanStatisticsDomainId OBJECT-TYPE SYNTAX Integer32(1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN ID" ::= { mvrVlanStatisticsEntry 1 } mvrVlanStatisticsVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN ID" ::= { mvrVlanStatisticsEntry 2 } mvrVlanStatisticsNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { mvrVlanStatisticsEntry 3 } mvrVlanStatisticsNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send." ::= { mvrVlanStatisticsEntry 4 } mvrVlanStatisticsNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join received " ::= { mvrVlanStatisticsEntry 5 } mvrVlanStatisticsNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of jion success " ::= { mvrVlanStatisticsEntry 6 } mvrVlanStatisticsNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send." ::= { mvrVlanStatisticsEntry 7 } mvrVlanStatisticsNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { mvrVlanStatisticsEntry 8} mvrVlanStatisticsNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send " ::= { mvrVlanStatisticsEntry 9} mvrVlanStatisticsNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received " ::= { mvrVlanStatisticsEntry 10} mvrVlanStatisticsNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send" ::= { mvrVlanStatisticsEntry 11} mvrVlanStatisticsNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sepcific query received " ::= { mvrVlanStatisticsEntry 12} mvrVlanStatisticsNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received" ::= { mvrVlanStatisticsEntry 13} mvrVlanStatisticsClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN statistics" ::= { mvrVlanStatisticsEntry 14} -- -- mvr6Mgmt -- mvr6DomainTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6DomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the MVR port." ::= { mvr6Mgt 1 } mvr6DomainEntry OBJECT-TYPE SYNTAX Mvr6DomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR Domain." INDEX {mvr6DomainId} ::= { mvr6DomainTable 1 } Mvr6DomainEntry ::= SEQUENCE { mvr6DomainId Integer32, mvr6DomainStatus EnabledStatus, mvr6DomainRunningStatus INTEGER, mvr6DomainVlanId VlanIndex, mvr6DomainUpstreamSourceIpv6 InetAddressIPv6, mvr6DomainClearDynamicGroups TruthValue } mvr6DomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Speicfies which MVR domain to configure." ::= { mvr6DomainEntry 1 } mvr6DomainStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable MVR(Multicast VLAN Registration) on the device." ::= { mvr6DomainEntry 2 } mvr6DomainRunningStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Describes the running status of MVR (Multicast VLAN Registration) to the switch. A value of active(1) indicates that all necessary conditions in the MVR environment are satisfied. A value of inactive(2) indicates that some necessary conditions in the MVR environment are not satisfied." ::= { mvr6DomainEntry 3 } mvr6DomainVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "To set VLAN for MVR.The VLAN identified by a particular value of this index is the same VLAN as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB." ::= { mvr6DomainEntry 4 } mvr6DomainUpstreamSourceIpv6 OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the source IP address which MVR will carry in IP header when send IGMP packet to upstream router through MVR source port." ::= { mvr6DomainEntry 5 } mvr6DomainClearDynamicGroups OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear dynamic learned groups" ::= { mvr6DomainEntry 6} mvr6DomainPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6DomainPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the MVR port." ::= { mvr6Mgt 2 } mvr6DomainPortEntry OBJECT-TYPE SYNTAX Mvr6DomainPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR port." INDEX { mvr6PortDomainId, mvr6DomainIfIndex } ::= { mvr6DomainPortTable 1 } Mvr6DomainPortEntry ::= SEQUENCE { mvr6PortDomainId Integer32, mvr6DomainIfIndex InterfaceIndex, mvr6DomainPortType INTEGER, mvr6DomainPortImmediateLeave EnabledStatus, mvr6DomainPortActive INTEGER, mvr6DomainPortImmediateLeaveByHostIp EnabledStatus } mvr6PortDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Speicfies which MVR domain to configure." ::= { mvr6DomainPortEntry 1 } mvr6DomainIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mvr6DomainPortEntry 2 } mvr6DomainPortType OBJECT-TYPE SYNTAX INTEGER { none(0), source(1), receiver(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "For configuring the MVR port type. To disable the MVR port type, use the none(0)." ::= { mvr6DomainPortEntry 3 } mvr6DomainPortImmediateLeave OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "To enable immediate leave on MVR port." ::= { mvr6DomainPortEntry 4 } mvr6DomainPortActive OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "To indicate if the port is associated with the MVR group. If the port is the MVR receiver port or the MVR source port in MVR vlan, the status is active(1); otherwise the status is inactive(2)." ::= { mvr6DomainPortEntry 5 } mvr6DomainPortImmediateLeaveByHostIp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "To enable immediate leave by host IP on MVR port." ::= { mvr6DomainPortEntry 6 } mvr6ProfileTable OBJECT IDENTIFIER ::= {mvr6Mgt 22 } mvr6ProfileCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6ProfileCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR6 profile." ::= { mvr6ProfileTable 1 } Mvr6ProfileCtlEntry ::= SEQUENCE { mvr6ProfileCtlId Integer32, mvr6ProfileName OCTET STRING, mvr6ProfileCtlAction INTEGER } mvr6ProfileCtlEntry OBJECT-TYPE SYNTAX Mvr6ProfileCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR6 profile." INDEX { mvr6ProfileCtlId } ::= { mvr6ProfileCtlTable 1 } mvr6ProfileCtlId OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR6 profile" ::= { mvr6ProfileCtlEntry 1 } mvr6ProfileName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "MVR6 Profile name which identify a group range. NOTE: All mvr6ProfileCtlEntry use the same buffer to temply store the mvrProfileName before mvr6ProfileCtlAction really creat the profile." ::= { mvr6ProfileCtlEntry 2 } mvr6ProfileCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(0), create(1), destory(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to create(2) to create profile. Set this object to destory(3) to delete profile. When the action is complete, this object becomes noAction(1)." ::= { mvr6ProfileCtlEntry 5 } mvr6ProfileGroupCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6ProfileGroupCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MVR group ranges for MVR6 profile." ::= { mvr6ProfileTable 2 } Mvr6ProfileGroupCtlEntry ::= SEQUENCE { mvr6ProfileGropuCtlProfileId Integer32, mvr6ProfileGroupCtlId Integer32, mvr6ProfileGroupStartIPAddress InetAddress, mvr6ProfileGroupEndIPAddress InetAddress, mvr6ProfileGroupCtlAction INTEGER } mvr6ProfileGroupCtlEntry OBJECT-TYPE SYNTAX Mvr6ProfileGroupCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the group ranges on MVR6 profile." INDEX {mvr6ProfileGropuCtlProfileId, mvr6ProfileGroupCtlId} ::= { mvr6ProfileGroupCtlTable 1 } mvr6ProfileGropuCtlProfileId OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR6 profile" ::= {mvr6ProfileGroupCtlEntry 1} mvr6ProfileGroupCtlId OBJECT-TYPE SYNTAX Integer32 (0..3) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which group range in MVR6 profile" ::= { mvr6ProfileGroupCtlEntry 2 } mvr6ProfileGroupStartIPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MVR Profile range start IP address. NOTE: All Mvr6ProfileGroupCtlEntry use the same buffer to temply store the mvr6ProfileStartIPAddress before mvr6ProfileGroupCtlAction really creat the group rang on profile." ::= { mvr6ProfileGroupCtlEntry 3} mvr6ProfileGroupEndIPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MVR6 Profile range end IP address. NOTE: All Mvr6ProfileGroupCtlEntry use the same buffer to temply store the mvr6ProfileEndIPAddress before mvr6ProfileGroupCtlAction really creat the group rang on profile." ::= { mvr6ProfileGroupCtlEntry 4 } mvr6ProfileGroupCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(0), create(1), destory(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to create(2) to create group range. Set this object to destory(3) to delete group range. When the action is complete, this object becomes noAction(1). NOTE: If mvr6ProfileGroupStartIPAddress and mvr6ProfileGroupEndIPAddress pattern already exist on other mvr6ProfileGroupCtlAction, it won't be stored." ::= { mvr6ProfileGroupCtlEntry 5 } mvr6DomainAssociatedProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6DomainAssociatedProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configure MVR domain associate which MVR profile" ::= {mvr6Mgt 4} mvr6DomainAssociatedProfileEntry OBJECT-TYPE SYNTAX Mvr6DomainAssociatedProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring MVR domain associate MVR profile." INDEX { mvr6ProfileDomainId, mvr6ProfileId } ::= { mvr6DomainAssociatedProfileTable 1 } Mvr6DomainAssociatedProfileEntry ::= SEQUENCE { mvr6ProfileDomainId Integer32, mvr6ProfileId Integer32, mvr6ProfileAction INTEGER } mvr6ProfileDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvr6DomainAssociatedProfileEntry 1 } mvr6ProfileId OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvr6DomainAssociatedProfileEntry 2 } mvr6ProfileAction OBJECT-TYPE SYNTAX INTEGER { noAction(0), create(1), destory(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this object to create(1) to associate profile. Set this object to destory(2) to deassociate profile. When the action is complete, this object becomes noAction(0)." ::= { mvr6DomainAssociatedProfileEntry 3 } mvr6DomainGroupStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6DomainGroupStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the static members of the MVR group." ::= { mvr6Mgt 5 } mvr6DomainGroupStaticEntry OBJECT-TYPE SYNTAX Mvr6DomainGroupStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the static members of the MVR group." INDEX { mvr6GroupStaticDomainId, mvr6DomainGroupStaticAddress, mvr6DomainGroupStaticReceiverVlan} ::= { mvr6DomainGroupStaticTable 1 } Mvr6DomainGroupStaticEntry ::= SEQUENCE { mvr6GroupStaticDomainId Integer32, mvr6DomainGroupStaticAddress InetAddressIPv6, mvr6DomainGroupStaticReceiverVlan Integer32, mvr6DomainGroupStaticPorts PortList } mvr6GroupStaticDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvr6DomainGroupStaticEntry 1 } mvr6DomainGroupStaticAddress OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast address of the MVR group." ::= { mvr6DomainGroupStaticEntry 2 } mvr6DomainGroupStaticReceiverVlan OBJECT-TYPE SYNTAX Integer32(1..4093) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The receiver vlan of this MVR group" ::= { mvr6DomainGroupStaticEntry 3 } mvr6DomainGroupStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports configured by management in this entry. Ports entered in this list will be the static members of this MVR group." ::= { mvr6DomainGroupStaticEntry 4 } mvr6DomainGroupCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6DomainGroupCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for the current members of the MVR group." ::= { mvr6Mgt 6 } mvr6DomainGroupCurrentEntry OBJECT-TYPE SYNTAX Mvr6DomainGroupCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for the current members of the MVR group." INDEX { mvr6GroupCurrenDomainId, mvr6DomainGroupCurrentAddress, mvr6DomainGroupCurrentReceiverVlan } ::= { mvr6DomainGroupCurrentTable 1 } Mvr6DomainGroupCurrentEntry ::= SEQUENCE { mvr6GroupCurrenDomainId Integer32, mvr6DomainGroupCurrentAddress OCTET STRING, mvr6DomainGroupCurrentReceiverVlan Integer32, mvr6DomainGroupCurrentPorts PortList } mvr6GroupCurrenDomainId OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Profile ID to index which MVR profile" ::= { mvr6DomainGroupCurrentEntry 1 } mvr6DomainGroupCurrentAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..47)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast address of the MVR group." ::= { mvr6DomainGroupCurrentEntry 2 } mvr6DomainGroupCurrentReceiverVlan OBJECT-TYPE SYNTAX Integer32(1..4093) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the receiver VLAN of the MVR group." ::= { mvr6DomainGroupCurrentEntry 3 } mvr6DomainGroupCurrentPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The complete set of ports currently associated with this MVR group." ::= { mvr6DomainGroupCurrentEntry 4 } mvr6ProxySwitching OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable MVR(Multicast VLAN Registration) proxy switching ability on the device. " ::= { mvr6Mgt 16 } mvr6RobustnessValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Paremete to set IGMP robustness value. This value apply to proxy-switching for how many IGMP report/leave will be send out from source port, and how many g-s query will be send on receiver port. " ::= { mvr6Mgt 17 } mvr6ProxyQueryInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the query interval that active receiver port will use to send out general query " ::= { mvr6Mgt 23 } mvr6SourcePortMode OBJECT-TYPE SYNTAX INTEGER { dynamic(1), forward(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Dynamic means active source port will only forward multicast stream when it has group joined. Forward means active source port will always forward MVR group range multicast streams recieved on another acitve source port." ::= { mvr6Mgt 24 } mvr6PortStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6PortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Mvr6 statistics VLAN." ::= {mvr6Mgt 26 } mvr6PortStatisticsEntry OBJECT-TYPE SYNTAX Mvr6PortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of Mvr6 statistics VLAN." INDEX { mvr6PortStatisticsDomainId, mvr6PortStatisticsPortIndex } ::= {mvr6PortStatisticsTable 1} Mvr6PortStatisticsEntry ::= SEQUENCE { mvr6PortStatisticsDomainId Integer32, mvr6PortStatisticsPortIndex InterfaceIndex, mvr6PortStatisticsNumGroups Unsigned32, mvr6PortStatisticsNumJoinSend Unsigned32, mvr6PortStatisticsNumJoins Unsigned32, mvr6PortStatisticsNumJoinSuccess Unsigned32, mvr6PortStatisticsNumLeavesSend Unsigned32, mvr6PortStatisticsNumLeaves Unsigned32, mvr6PortStatisticsNumGeneralQuerySend Unsigned32, mvr6PortStatisticsNumGeneralQueryRecevied Unsigned32, mvr6PortStatisticsNumSepcificQuerySend Unsigned32, mvr6PortStatisticsNumSpecificQueryReceived Unsigned32, mvr6PortStatisticsNumInvalidReport Unsigned32, mvr6PortStatisticsClearStatistics TruthValue } mvr6PortStatisticsDomainId OBJECT-TYPE SYNTAX Integer32(1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the mvr6PortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mvr6PortStatisticsEntry 1 } mvr6PortStatisticsPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the mvr6PortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mvr6PortStatisticsEntry 2 } mvr6PortStatisticsNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { mvr6PortStatisticsEntry 3 } mvr6PortStatisticsNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send " ::= { mvr6PortStatisticsEntry 4 } mvr6PortStatisticsNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join recieved " ::= { mvr6PortStatisticsEntry 5 } mvr6PortStatisticsNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join group success " ::= { mvr6PortStatisticsEntry 6 } mvr6PortStatisticsNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send" ::= { mvr6PortStatisticsEntry 7 } mvr6PortStatisticsNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { mvr6PortStatisticsEntry 8} mvr6PortStatisticsNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send. " ::= { mvr6PortStatisticsEntry 9} mvr6PortStatisticsNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received. " ::= { mvr6PortStatisticsEntry 10} mvr6PortStatisticsNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send. " ::= { mvr6PortStatisticsEntry 11} mvr6PortStatisticsNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query received. " ::= { mvr6PortStatisticsEntry 12} mvr6PortStatisticsNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received. " ::= { mvr6PortStatisticsEntry 13} mvr6PortStatisticsClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN all statistics " ::= { mvr6PortStatisticsEntry 14} mvr6VlanStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF Mvr6VlanStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Mvr6 statistics VLAN." ::= {mvr6Mgt 27 } mvr6VlanStatisticsEntry OBJECT-TYPE SYNTAX Mvr6VlanStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of Mvr6 statistics VLAN." INDEX { mvr6VlanStatisticsDomainId, mvr6VlanStatisticsVlanId } ::= {mvr6VlanStatisticsTable 1} Mvr6VlanStatisticsEntry ::= SEQUENCE { mvr6VlanStatisticsDomainId Integer32, mvr6VlanStatisticsVlanId VlanIndex, mvr6VlanStatisticsNumGroups Unsigned32, mvr6VlanStatisticsNumJoinSend Unsigned32, mvr6VlanStatisticsNumJoins Unsigned32, mvr6VlanStatisticsNumJoinSuccess Unsigned32, mvr6VlanStatisticsNumLeavesSend Unsigned32, mvr6VlanStatisticsNumLeaves Unsigned32, mvr6VlanStatisticsNumGeneralQuerySend Unsigned32, mvr6VlanStatisticsNumGeneralQueryRecevied Unsigned32, mvr6VlanStatisticsNumSepcificQuerySend Unsigned32, mvr6VlanStatisticsNumSpecificQueryReceived Unsigned32, mvr6VlanStatisticsNumInvalidReport Unsigned32, mvr6VlanStatisticsClearStatistics TruthValue } mvr6VlanStatisticsDomainId OBJECT-TYPE SYNTAX Integer32(1..5) MAX-ACCESS not-accessible STATUS current DESCRIPTION "domain ID" ::= { mvr6VlanStatisticsEntry 1 } mvr6VlanStatisticsVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN ID" ::= { mvr6VlanStatisticsEntry 2 } mvr6VlanStatisticsNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { mvr6VlanStatisticsEntry 3 } mvr6VlanStatisticsNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send." ::= { mvr6VlanStatisticsEntry 4 } mvr6VlanStatisticsNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join received " ::= { mvr6VlanStatisticsEntry 5 } mvr6VlanStatisticsNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of jion success " ::= { mvr6VlanStatisticsEntry 6 } mvr6VlanStatisticsNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send." ::= { mvr6VlanStatisticsEntry 7 } mvr6VlanStatisticsNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { mvr6VlanStatisticsEntry 8} mvr6VlanStatisticsNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send " ::= { mvr6VlanStatisticsEntry 9} mvr6VlanStatisticsNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received " ::= { mvr6VlanStatisticsEntry 10} mvr6VlanStatisticsNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send" ::= { mvr6VlanStatisticsEntry 11} mvr6VlanStatisticsNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sepcific query received " ::= { mvr6VlanStatisticsEntry 12} mvr6VlanStatisticsNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received" ::= { mvr6VlanStatisticsEntry 13} mvr6VlanStatisticsClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN statistics" ::= { mvr6VlanStatisticsEntry 14} mvr6ForwardingPriority OBJECT-TYPE SYNTAX Integer32(0..7|65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure MVR multicast stream forwarding priority. If value is 65535, it means the priority is disabled." ::= { mvr6Mgt 28 } -- -- dhcpSnoopMgt -- -- Management of DHCP snooping and IP souce guard. dhcpSnoopGlobal OBJECT IDENTIFIER ::= { dhcpSnoopMgt 1 } dhcpSnoopVlan OBJECT IDENTIFIER ::= { dhcpSnoopMgt 2 } dhcpSnoopInterface OBJECT IDENTIFIER ::= { dhcpSnoopMgt 3 } dhcpSnoopBindings OBJECT IDENTIFIER ::= { dhcpSnoopMgt 4 } dhcpSnoopStatistics OBJECT IDENTIFIER ::= { dhcpSnoopMgt 5 } dhcpSnoopEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the DHCP Snooping feature is enabled." ::= { dhcpSnoopGlobal 1 } dhcpSnoopVerifyMacAddressEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP Snooping Mac address verification is enabled." ::= { dhcpSnoopGlobal 2 } dhcpSnoopInformationOptionEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the DHCP snooping information option(option 82) feature is enabled." ::= { dhcpSnoopGlobal 3 } dhcpSnoopInformationOptionPolicy OBJECT-TYPE SYNTAX INTEGER { drop(1), keep(2), replace(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates which reforwarding policy shall be used for DHCP snooping information option(option 82). A value of drop(1) means to drop the DHCP request packet which has the information option(option 82). A value of keep(2) means to keep the existing information option(option 82) of the DHCP request packet. A value of replace(3), which is the default value, means to replace the existing information option(option 82) of the DHCP request packet." ::= { dhcpSnoopGlobal 4 } dhcpSnoopBindingsTableCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), store(2), clear(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set this to store(2) to store DHCP snooping binding entries to flash. Set this to clear(3) to clear DHCP snooping binding entries from flash. noAction(1) will always be obtained when reading this variable." ::= { dhcpSnoopGlobal 5 } dhcpSnoopLimitRate OBJECT-TYPE SYNTAX Integer32(0..2048) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the limit rate that DHCP packet redirected to CPU. Set this to 0 means no rate limit for DHCP packet." ::= { dhcpSnoopGlobal 6} -- dhcpSnoopVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains DHCP Snooping configurations of existing VLANs." ::= { dhcpSnoopVlan 1 } dhcpSnoopVlanConfigEntry OBJECT-TYPE SYNTAX DhcpSnoopVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the configuration to enable or disable DHCP Snooping at each existing VLAN." INDEX { dhcpSnoopVlanIndex } ::= { dhcpSnoopVlanConfigTable 1 } DhcpSnoopVlanConfigEntry ::= SEQUENCE { dhcpSnoopVlanIndex VlanIndex, dhcpSnoopVlanEnable EnabledStatus } dhcpSnoopVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the VLAN ID on which DHCP Snooping feature is configured." ::= { dhcpSnoopVlanConfigEntry 1 } dhcpSnoopVlanEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP Snooping is enabled in this VLAN." ::= { dhcpSnoopVlanConfigEntry 2 } -- dhcpSnoopPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to configure the trust state of each port or trunk for DHCP Snooping purpose." ::= { dhcpSnoopInterface 1 } dhcpSnoopPortConfigEntry OBJECT-TYPE SYNTAX DhcpSnoopPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the configuration to enable or disable trust state of each port or trunk for DHCP Snooping purpose." INDEX { dhcpSnoopPortIfIndex } ::= { dhcpSnoopPortConfigTable 1 } DhcpSnoopPortConfigEntry ::= SEQUENCE { dhcpSnoopPortIfIndex InterfaceIndex, dhcpSnoopPortTrustEnable EnabledStatus, dhcpSnoopPortMaxNumber Integer32 } dhcpSnoopPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the port or trunk." ::= { dhcpSnoopPortConfigEntry 1 } dhcpSnoopPortTrustEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the port or trunk is trusted for DHCP Snooping purpose." ::= { dhcpSnoopPortConfigEntry 2 } dhcpSnoopPortMaxNumber OBJECT-TYPE SYNTAX Integer32(1..1024|65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the max client number of per port. If the value is 65535, it means the filter-only mode is enabled." ::= { dhcpSnoopPortConfigEntry 6} -- dhcpSnoopBindingsTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopBindingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the DHCP bindings information learnt by the device." ::= { dhcpSnoopBindings 1 } dhcpSnoopBindingsEntry OBJECT-TYPE SYNTAX DhcpSnoopBindingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the Mac address, IP address type, IP address, VLAN number, interface number, leased time and status." INDEX { dhcpSnoopBindingsIpAddress, dhcpSnoopBindingsMacAddress } ::= { dhcpSnoopBindingsTable 1 } DhcpSnoopBindingsEntry ::= SEQUENCE { dhcpSnoopBindingsVlanIndex VlanIndex, dhcpSnoopBindingsMacAddress MacAddress, dhcpSnoopBindingsAddrType InetAddressType, dhcpSnoopBindingsEntryType INTEGER, dhcpSnoopBindingsIpAddress IpAddress, dhcpSnoopBindingsPortIfIndex InterfaceIndex, dhcpSnoopBindingsLeaseTime Unsigned32 } dhcpSnoopBindingsVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VLAN which a DHCP client host belongs to." ::= { dhcpSnoopBindingsEntry 1 } dhcpSnoopBindingsMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the MAC address of a DHCP client host." ::= { dhcpSnoopBindingsEntry 2 } dhcpSnoopBindingsAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of IP address denoted in dhcpSnoopBindingsIpAddress type." ::= { dhcpSnoopBindingsEntry 3 } dhcpSnoopBindingsEntryType OBJECT-TYPE SYNTAX INTEGER { dynamic(1), static(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates that this binding is obtained from dynamically learning or is a static configuraion." ::= { dhcpSnoopBindingsEntry 4 } dhcpSnoopBindingsIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the allocated IP address of a DHCP client host." ::= { dhcpSnoopBindingsEntry 5 } dhcpSnoopBindingsPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port or trunk where a DHCP client host connects to." ::= { dhcpSnoopBindingsEntry 6 } dhcpSnoopBindingsLeaseTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the leased time of this DHCP bindings." ::= { dhcpSnoopBindingsEntry 7 } -- dhcpSnoopTotalForwardedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of packets subjected to DHCP Snooping is forwarded." ::= { dhcpSnoopStatistics 1 } dhcpSnoopUntrustedPortDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of packets subjected to DHCP Snooping is dropped because they come from untrusted interface." ::= { dhcpSnoopStatistics 3 } -- -- clusterMgt -- clusterEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables clustering on the device." ::= { clusterMgt 1 } clusterCommanderEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables the device as commander in a cluster." ::= { clusterMgt 2 } clusterIpPool OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The start internal IP address of a cluster pool." ::= { clusterMgt 4 } clusterClearCandidateTable OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to clear(2) starts to clear the candidate table." ::= { clusterMgt 5 } clusterRole OBJECT-TYPE SYNTAX INTEGER { commander(1), candidate(2), activeMember(3), disabled(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current role of the device in a cluster. commander(1) : The switch is the controlling device in a cluster. candidate(2) : The switch has been discovered by the commander, but it has not been manually configured for access from the commander. activeMember(3): The switch has been manually configured for access from the commander and it is active in the cluster. disabled(5) : The switch has clustering disabled." ::= { clusterMgt 6 } clusterMemberCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of members in a cluster." ::= { clusterMgt 7 } clusterCandidateCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of candidates in a cluster." ::= { clusterMgt 8 } clusterCandidateTable OBJECT-TYPE SYNTAX SEQUENCE OF ClusterCandidateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing cluster candidates." ::= { clusterMgt 9 } clusterCandidateEntry OBJECT-TYPE SYNTAX ClusterCandidateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the information of the candidate." INDEX { clusterCandidateMacAddr} ::= { clusterCandidateTable 1 } ClusterCandidateEntry ::= SEQUENCE { clusterCandidateMacAddr MacAddress, clusterCandidateDesc DisplayString, clusterCandidateRole INTEGER } clusterCandidateMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address of the candidate." ::= {clusterCandidateEntry 1 } clusterCandidateDesc OBJECT-TYPE SYNTAX DisplayString (SIZE (0..42)) MAX-ACCESS read-only STATUS current DESCRIPTION "The description of the candidate." ::= {clusterCandidateEntry 3 } clusterCandidateRole OBJECT-TYPE SYNTAX INTEGER { candidate(2), activeMember(3), inactiveMember(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The role of the candidate. candidate(2) : The switch is discovered by the commander, but it has not been manually configured for access from the commander. activeMember(3) : The switch is manually configured for access from the commander and it is active in the cluster. inactiveMember(4): The switch is manually configured for access from the commander, but it is inactive in the cluster." ::= {clusterCandidateEntry 4 } clusterMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF ClusterMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table listing clustering members." ::= { clusterMgt 10 } clusterMemberEntry OBJECT-TYPE SYNTAX ClusterMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the information of the member." INDEX { clusterMemberId} ::= { clusterMemberTable 1 } ClusterMemberEntry ::= SEQUENCE { clusterMemberId Unsigned32, clusterMemberMacAddr MacAddress, clusterMemberDesc DisplayString, clusterMemberActive INTEGER } clusterMemberId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ID of the member." ::= {clusterMemberEntry 1 } clusterMemberMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the member." ::= {clusterMemberEntry 2 } clusterMemberDesc OBJECT-TYPE SYNTAX DisplayString(SIZE (0..42)) MAX-ACCESS read-only STATUS current DESCRIPTION "The description of the member." ::= {clusterMemberEntry 3 } clusterMemberActive OBJECT-TYPE SYNTAX INTEGER { activeMember(3), inactiveMember(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The active status of the member. activeMember(3) : The switch is manually configured for access from the commander and it is active in the cluster. inactiveMember(4): The switch is manually configured for access from the commander, but it is inactive in the cluster." ::= {clusterMemberEntry 4 } clusterMemberAddCtl OBJECT IDENTIFIER ::= { clusterMgt 11 } clusterMemberAddCtlMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The MAC address of the device associated with clusterMemberAddCtlAction." ::= { clusterMemberAddCtl 1 } clusterMemberAddCtlId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The member id associated with clusterMemberAddCtlAction." ::= { clusterMemberAddCtl 2 } clusterMemberAddCtlAction OBJECT-TYPE SYNTAX INTEGER { noAdd(1), add(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Adds the device to members that can be accessed from the commander. The MAC of the device is the current value of clusterMemberAddCtlMacAddr and the assigned member ID is the current value of clusterMemberAddCtlId. Set this object to add(2) to begin adding the member." ::= { clusterMemberAddCtl 5 } clusterMemberRemoveCtl OBJECT IDENTIFIER ::= { clusterMgt 12 } clusterMemberRemoveCtlId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The member ID associated with clusterMemberRemoveCtlAction." ::= { clusterMemberRemoveCtl 1 } clusterMemberRemoveCtlAction OBJECT-TYPE SYNTAX INTEGER { noRemove(1), remove(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Removes the device from members that can be accessed from the commander. The member ID is the current value of clusterMemberRemoveCtlId. Set this object to remove(2) to begin removing the member." ::= { clusterMemberRemoveCtl 2 } -- -- ipSrcGuardMgt -- ipSrcGuardConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF IpSrcGuardConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the configurations to enable or disable IP Source Guard at each port or trunk." ::= { ipSrcGuardMgt 1 } ipSrcGuardConfigEntry OBJECT-TYPE SYNTAX IpSrcGuardConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the configuration to enable or disable IP Source Guard at each port or trunk." INDEX { ipSrcGuardPortIfIndex } ::= { ipSrcGuardConfigTable 1 } IpSrcGuardConfigEntry ::= SEQUENCE { ipSrcGuardPortIfIndex InterfaceIndex, ipSrcGuardMode INTEGER } ipSrcGuardPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object idents the port or trunk which is capable of IP Source Guard feature." ::= { ipSrcGuardConfigEntry 1 } ipSrcGuardMode OBJECT-TYPE SYNTAX INTEGER { diabled(0), srcIp(1), srcIpMac(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether Ip Source Guard is enabled at this interface. If the value equals 0, it means Ip Source Guard is disabled. If the value equals 1, it means Ip Source Guard is enabled, and packets are filtered by checking source ip. If the value equals 2, it means Ip Source Guard is enabled and packets are filtered by checking source ip and source mac." ::= { ipSrcGuardConfigEntry 2 } -- ipSrcGuardAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IpSrcGuardAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the IP Source Guard bindings information learnt by the device." ::= { ipSrcGuardMgt 2 } ipSrcGuardAddrEntry OBJECT-TYPE SYNTAX IpSrcGuardAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the Mac address, IP address type, IP address, VLAN number, interface number, leased time and status." INDEX { ipSrcGuardBindingsIpAddress, ipSrcGuardBindingsMacAddress } ::= { ipSrcGuardAddrTable 1 } IpSrcGuardAddrEntry ::= SEQUENCE { ipSrcGuardBindingsVlanIndex VlanIndex, ipSrcGuardBindingsMacAddress MacAddress, ipSrcGuardBindingsAddrType InetAddressType, ipSrcGuardBindingsEntryType INTEGER, ipSrcGuardBindingsIpAddress IpAddress, ipSrcGuardBindingsPortIfIndex InterfaceIndex, ipSrcGuardBindingsLeaseTime Unsigned32, ipSrcGuardBindingsStatus RowStatus } ipSrcGuardBindingsVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the VLAN which a DHCP client host belongs to." ::= { ipSrcGuardAddrEntry 1 } ipSrcGuardBindingsMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the MAC address of a DHCP client host." ::= { ipSrcGuardAddrEntry 2 } ipSrcGuardBindingsAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the type of IP address denoted in ipSrcGuardBindingsIpAddress type." ::= { ipSrcGuardAddrEntry 3 } ipSrcGuardBindingsEntryType OBJECT-TYPE SYNTAX INTEGER { dynamic(1), static(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates that this binding is obtained from dynamically learning or is a static configuraion." ::= { ipSrcGuardAddrEntry 4 } ipSrcGuardBindingsIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the allocated IP address of a DHCP client host." ::= { ipSrcGuardAddrEntry 5 } ipSrcGuardBindingsPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the port or trunk where a DHCP client host connects to." ::= { ipSrcGuardAddrEntry 6 } ipSrcGuardBindingsLeaseTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the leased time of this DHCP bindings." ::= { ipSrcGuardAddrEntry 7 } ipSrcGuardBindingsStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object issued to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device." ::= { ipSrcGuardAddrEntry 8 } -- -- upnpMgt -- upnpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Sets enabled(1) to enable UPnP device, and sets disabled(2) to disable UPnP device." ::= { upnpMgt 1 } upnpAdvertisingDuration OBJECT-TYPE SYNTAX Integer32 (60..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval(in seconds) between available UPnP device advertising messages sent by the switch." ::= { upnpMgt 2 } upnpTtl OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the TTL value of the UPnP advertising messages sent by the switch. When the TTL value is greater than 1, it is possible to send UPnP advertising messages to traverse multiple routers; at the same time, the UPnP device will send an IGMP Join message to the traverse multiple routers so that the routers will forward multicast messages to the UPnP device." ::= { upnpMgt 3 } -- -- oamMgt -- oamPortClearStatTable OBJECT-TYPE SYNTAX SEQUENCE OF OamPortClearStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the information of clear OAM statistics at each port." ::= { oamMgt 3 } oamPortClearStatEntry OBJECT-TYPE SYNTAX OamPortClearStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains the information of clear OAM statistics at each port." INDEX { oamPortClearStatIndex } ::= { oamPortClearStatTable 1 } OamPortClearStatEntry ::= SEQUENCE { oamPortClearStatIndex InterfaceIndex, oamClearStatistics INTEGER } oamPortClearStatIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object shows the ifIndex value of the port excluding trunk." ::= { oamPortClearStatEntry 1 } oamClearStatistics OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear the counters for OAM. Set this variable to clear(2) to perform the clear operation, noClear(1) will always be displayed when reading this variable." ::= { oamPortClearStatEntry 2 } oamLoopbackTable OBJECT-TYPE SYNTAX SEQUENCE OF OamLoopbackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for OAM remote loopback test." ::= { oamMgt 4 } oamLoopbackEntry OBJECT-TYPE SYNTAX OamLoopbackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for OAM remote loopback test." INDEX { oamLoopbackTestIfIndex } ::= { oamLoopbackTable 1 } OamLoopbackEntry ::= SEQUENCE { oamLoopbackTestIfIndex InterfaceIndex, oamLoopbackTestPacketNumber Integer32, oamLoopbackTestPacketSize Integer32, oamLoopbackTestAction INTEGER, oamLoopbackTestResultTx Counter32, oamLoopbackTestResultRx Counter32, oamLoopbackTestResultLossRate Integer32 } oamLoopbackTestIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the port (excluding trunk and trunk members). The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { oamLoopbackEntry 1 } oamLoopbackTestPacketNumber OBJECT-TYPE SYNTAX Integer32(1..99999999) MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the packet number when performing loopback test." ::= { oamLoopbackEntry 2} oamLoopbackTestPacketSize OBJECT-TYPE SYNTAX Integer32(64..1518) MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the packet size when performing loopback test." ::= { oamLoopbackEntry 3 } oamLoopbackTestAction OBJECT-TYPE SYNTAX INTEGER { noTest(1), test(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to test(2) to begin the loopback test. This object will be noTest(1) when the loopback test is canceled or the loopback test has finished." ::= { oamLoopbackEntry 4} oamLoopbackTestResultTx OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the the total number of loopback frames transmitted at last loopback test on this interface." ::= { oamLoopbackEntry 5} oamLoopbackTestResultRx OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the the total number of loopback frames received at last loopback test on this interface." ::= { oamLoopbackEntry 6} oamLoopbackTestResultLossRate OBJECT-TYPE SYNTAX Integer32 (0..10000) MAX-ACCESS read-only STATUS current DESCRIPTION "Packet loss rate of this loopback test operation in hundredths of a percent. This variable is calculated by oamLoopbackTestResultRx and oamLoopbackTestResultTx." ::= { oamLoopbackEntry 7} oamPrivateEventLogType OBJECT-TYPE SYNTAX INTEGER { connectionToRemoteDeviceUp(1001), connectionToRemoteDeviceDown(1002), linkFaultClear(1003), dyingGaspEventClear(1004), criticalLinkEventClear(1005) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object augments the dot3OamEventLogType of dot3OamEventLogTable in DOT3-OAM-MIB. When the OUI (dot3OamEventLogOui) is 0x0012CF, the following event types are defined: connectionToRemoteDeviceUp(1001), connectionToRemoteDeviceDown(1002), linkFaultClear(1003), dyingGaspEventClear(1004), criticalLinkEventClear(1005) All these events are not threshold crossing events." ::= { oamMgt 5 } oamPortClearEventLogTable OBJECT-TYPE SYNTAX SEQUENCE OF OamPortClearEventLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the information of clear OAM event log at each port." ::= { oamMgt 6 } oamPortClearEventLogEntry OBJECT-TYPE SYNTAX OamPortClearEventLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing the information of clear OAM event log at each port." INDEX { oamPortClearEventLogIndex } ::= { oamPortClearEventLogTable 1 } OamPortClearEventLogEntry ::= SEQUENCE { oamPortClearEventLogIndex InterfaceIndex, oamPortClearEventLogAction INTEGER } oamPortClearEventLogIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the port (excluding trunk and trunk members). The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { oamPortClearEventLogEntry 1 } oamPortClearEventLogAction OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear the event log for OAM. Set this variable to clear(2) to perform the clear operation. noClear(1) will always be displayed when reading this variable." ::= { oamPortClearEventLogEntry 2 } -- -- mldSnoopMgt -- -- Management for MLD -- Snooping. mldSnoopStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable MLD snooping on the device. When enabled, the device will examine MLD packets and set up filters for MLD ports. " DEFVAL { disabled } ::= { mldSnoopMgt 1 } mldSnoopQuerier OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enables (disables) whether the switch acts as an MLD querier." DEFVAL { disabled } ::= { mldSnoopMgt 2 } mldSnoopRobustness OBJECT-TYPE SYNTAX Integer32 (2..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. MLD is robust to (Robustness Variable-1) packet losses. The discussion of the Robustness Variable is in Section 7.1 of RFC 2710." DEFVAL { 2 } ::= { mldSnoopMgt 3 } mldSnoopQueryInterval OBJECT-TYPE SYNTAX Integer32 (60..125) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval (in seconds) between MLD host-query messages sent by the switch." DEFVAL { 125 } ::= { mldSnoopMgt 4 } mldSnoopQueryMaxResponseTime OBJECT-TYPE SYNTAX Integer32 (5..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The time after a query, during which a response is expected from an endstation. If a querier has sent a number of queries defined by mldSnoopRobustness, but an endstation has not responded, a countdown timer is started using an initial value set by mldSnoopQueryMaxResponseTime. If the countdown finishes, and the endstation still has not responded, then that the endstation is deemed to have left the multicast group." DEFVAL { 10 } ::= { mldSnoopMgt 5 } mldSnoopRouterPortExpireTime OBJECT-TYPE SYNTAX Integer32 (300..500) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the time (in seconds) the switch waits after the previous querier has stopped querying before the router port (which received query packets from previous querier) expires." DEFVAL { 300 } ::= { mldSnoopMgt 6 } mldSnoopVersion OBJECT-TYPE SYNTAX Integer32 (1..2) MAX-ACCESS read-write STATUS current DESCRIPTION "MLD version snooped" DEFVAL { 2 } ::= { mldSnoopMgt 7 } mldSnoopUnknownMcastMode OBJECT-TYPE SYNTAX INTEGER { flood(1), toRouterPort(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the mldSnoopUnknownMcastMode to define the flooding behavior when receive the unknown multicast traffic." ::= { mldSnoopMgt 8 } mldSnoopRouterCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopRouterCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for current router ports." ::= { mldSnoopMgt 9 } mldSnoopRouterCurrentEntry OBJECT-TYPE SYNTAX MldSnoopRouterCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for current router ports." INDEX { mldSnoopRouterCurrentVlanIndex } ::= {mldSnoopRouterCurrentTable 1 } MldSnoopRouterCurrentEntry ::= SEQUENCE { mldSnoopRouterCurrentVlanIndex Unsigned32, mldSnoopRouterCurrentPorts PortList } mldSnoopRouterCurrentVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to mldSnoopRouterStaticTable." ::= { mldSnoopRouterCurrentEntry 1 } mldSnoopRouterCurrentPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are current router ports, including static router ports. Please refer to mldSnoopRouterStaticTable." ::= { mldSnoopRouterCurrentEntry 2 } mldSnoopRouterStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopRouterStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for static router ports." ::= { mldSnoopMgt 10 } mldSnoopRouterStaticEntry OBJECT-TYPE SYNTAX MldSnoopRouterStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for static router ports." INDEX { mldSnoopRouterStaticVlanIndex } ::= { mldSnoopRouterStaticTable 1 } MldSnoopRouterStaticEntry ::= SEQUENCE { mldSnoopRouterStaticVlanIndex Unsigned32, mldSnoopRouterStaticPorts PortList } mldSnoopRouterStaticVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to mldSnoopRouterStaticTable." ::= { mldSnoopRouterStaticEntry 1 } mldSnoopRouterStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are static router ports." ::= { mldSnoopRouterStaticEntry 2 } mldSnoopMulticastCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopMulticastCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for current multicast addresses." ::= { mldSnoopMgt 11 } mldSnoopMulticastCurrentEntry OBJECT-TYPE SYNTAX MldSnoopMulticastCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for current multicast addresses." INDEX { mldSnoopMulticastCurrentVlanIndex, mldSnoopMulticastCurrentIpAddress, mldSnoopMulticastCurrentSourceIpAddress } ::= { mldSnoopMulticastCurrentTable 1 } MldSnoopMulticastCurrentEntry ::= SEQUENCE { mldSnoopMulticastCurrentVlanIndex Unsigned32, mldSnoopMulticastCurrentIpAddress InetAddressIPv6, mldSnoopMulticastCurrentSourceIpAddress InetAddressIPv6, mldSnoopMulticastCurrentPorts PortList } mldSnoopMulticastCurrentVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to mldSnoopMulticastStaticTable." ::= { mldSnoopMulticastCurrentEntry 1 } mldSnoopMulticastCurrentIpAddress OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS not-accessible STATUS current DESCRIPTION "IPv6 address of multicast group." ::= { mldSnoopMulticastCurrentEntry 2 } mldSnoopMulticastCurrentSourceIpAddress OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS not-accessible STATUS current DESCRIPTION "IPv6 address of the source." ::= { mldSnoopMulticastCurrentEntry 3 } mldSnoopMulticastCurrentPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are members of a multicast group, including static members. Please refer to mldSnoopMulticastStaticTable." ::= { mldSnoopMulticastCurrentEntry 4 } mldSnoopMulticastStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopMulticastStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for static multicast addresses." ::= { mldSnoopMgt 12 } mldSnoopMulticastStaticEntry OBJECT-TYPE SYNTAX MldSnoopMulticastStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for static multicast addresses." INDEX { mldSnoopMulticastStaticVlanIndex, mldSnoopMulticastStaticIpAddress } ::= { mldSnoopMulticastStaticTable 1 } MldSnoopMulticastStaticEntry ::= SEQUENCE { mldSnoopMulticastStaticVlanIndex Unsigned32, mldSnoopMulticastStaticIpAddress InetAddressIPv6, mldSnoopMulticastStaticPorts PortList } mldSnoopMulticastStaticVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to mldSnoopMulticastStaticTable." ::= { mldSnoopMulticastStaticEntry 1 } mldSnoopMulticastStaticIpAddress OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS not-accessible STATUS current DESCRIPTION "IPv6 address of multicast group." ::= { mldSnoopMulticastStaticEntry 2 } mldSnoopMulticastStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are members." ::= { mldSnoopMulticastStaticEntry 3 } mldSnoopCurrentVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopCurrentVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for configuring MLD snooping for each VLAN which exists in the device by (local or network) management, or dynamically created as a result of GVRP requests received." ::= { mldSnoopMgt 13 } mldSnoopCurrentVlanEntry OBJECT-TYPE SYNTAX MldSnoopCurrentVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for configuring MLD snooping." INDEX { mldSnoopCurrentVlanIndex } ::= { mldSnoopCurrentVlanTable 1 } MldSnoopCurrentVlanEntry ::= SEQUENCE { mldSnoopCurrentVlanIndex Unsigned32, mldSnoopCurrentVlanImmediateLeave EnabledStatus, mldSnoopCurrentVlanImmediateLeaveByHostIp EnabledStatus } mldSnoopCurrentVlanIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface." ::= { mldSnoopCurrentVlanEntry 1 } mldSnoopCurrentVlanImmediateLeave OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter to enable or disable the Immediate-Leave feature on this VLAN." ::= { mldSnoopCurrentVlanEntry 2 } mldSnoopCurrentVlanImmediateLeaveByHostIp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The parameter to enable or disable the Immediate-Leave by-host-ip feature on this VLAN." ::= { mldSnoopCurrentVlanEntry 3 } mldSnoopProxyReporting OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable MLD snooping proxy reporting on the device." DEFVAL { enabled } ::= { mldSnoopMgt 14 } mldSnoopUnsolicitedReportInterval OBJECT-TYPE SYNTAX Unsigned32(1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to specify how long (in seconds) the uplink ports should transmit unsolicited reports." DEFVAL { 400 } ::= { mldSnoopMgt 15 } mldSnoopPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of MLD Snooping service per port." ::= {mldSnoopMgt 16 } mldSnoopPortEntry OBJECT-TYPE SYNTAX MldSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of MLD Snooping service per port." INDEX { mldSnoopPortIndex } ::= {mldSnoopPortTable 1} MldSnoopPortEntry ::= SEQUENCE { mldSnoopPortIndex Unsigned32, mldSnoopQueryDrop INTEGER, mldSnoopMulticastDataDrop INTEGER, mldSnoopPortNumGroups Unsigned32, mldSnoopPortNumJoinSend Unsigned32, mldSnoopPortNumJoins Unsigned32, mldSnoopPortNumJoinSuccess Unsigned32, mldSnoopPortNumLeavesSend Unsigned32, mldSnoopPortNumLeaves Unsigned32, mldSnoopPortNumGeneralQuerySend Unsigned32, mldSnoopPortNumGeneralQueryRecevied Unsigned32, mldSnoopPortNumSepcificQuerySend Unsigned32, mldsnoopPortNumSpecificQueryReceived Unsigned32, mldSnoopPortNumInvalidReport Unsigned32, mldSnoopPortClearStatistics TruthValue } mldSnoopPortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the mldsnpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { mldSnoopPortEntry 1 } mldSnoopQueryDrop OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable dropping MLD Query packet." DEFVAL { disable } ::= { mldSnoopPortEntry 3 } mldSnoopMulticastDataDrop OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable dropping IPv6 multicast data " DEFVAL { disable } ::= { mldSnoopPortEntry 4 } mldSnoopPortNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { mldSnoopPortEntry 5 } mldSnoopPortNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send " ::= { mldSnoopPortEntry 6 } mldSnoopPortNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join recieved " ::= { mldSnoopPortEntry 7 } mldSnoopPortNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join group success " ::= { mldSnoopPortEntry 8 } mldSnoopPortNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send" ::= { mldSnoopPortEntry 9 } mldSnoopPortNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { mldSnoopPortEntry 10} mldSnoopPortNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send. " ::= { mldSnoopPortEntry 11} mldSnoopPortNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received. " ::= { mldSnoopPortEntry 12} mldSnoopPortNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send. " ::= { mldSnoopPortEntry 13} mldsnoopPortNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query received. " ::= { mldSnoopPortEntry 14} mldSnoopPortNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received. " ::= { mldSnoopPortEntry 15} mldSnoopPortClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN all statistics " ::= { mldSnoopPortEntry 16} mldSnoopFilterStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable MLD filtering on the device." ::= { mldSnoopMgt 17 } mldSnoopProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the MLD snooping profile." ::= { mldSnoopMgt 18 } mldSnoopProfileEntry OBJECT-TYPE SYNTAX MldSnoopProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the MLD snooping profile." INDEX { mldSnoopProfileId } ::= { mldSnoopProfileTable 1 } MldSnoopProfileEntry ::= SEQUENCE { mldSnoopProfileId Unsigned32, mldSnoopProfileAction INTEGER, mldSnoopProfileStatus ValidStatus } mldSnoopProfileId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ID of the MLD snooping profile." ::= { mldSnoopProfileEntry 1 } mldSnoopProfileAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The access mode of the MLD snooping profile." DEFVAL { deny } ::= { mldSnoopProfileEntry 2 } mldSnoopProfileStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { mldSnoopProfileEntry 3 } mldSnoopProfileCtl OBJECT IDENTIFIER ::= { mldSnoopMgt 19 } mldSnoopProfileCtlId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The ID of the MLD snooping profile. The default value is zero, meaning that no ID is specified. In order to create a profile, a non-zero value must be specified." ::= { mldSnoopProfileCtl 1 } mldSnoopProfileCtlInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The address type is associated with this agent. Only ipv4(1) type is supported." ::= { mldSnoopProfileCtl 2 } mldSnoopProfileCtlStartInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The specified addresses in the start of the controlled IP multicast addresses." ::= { mldSnoopProfileCtl 3 } mldSnoopProfileCtlEndInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The specified addresses in the end of the controlled IP multicast addresses." ::= { mldSnoopProfileCtl 4 } mldSnoopProfileCtlAction OBJECT-TYPE SYNTAX INTEGER { noAction(1), create(2), destroy(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting it to create(2) creates the range of the controlled IP multicast addresses. Setting it to destroy(3) destroys the range of the controlled IP multicast addresses. When the action is completed, this object becomes noAction(1)." ::= { mldSnoopProfileCtl 5 } mldSnoopProfileRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopProfileRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for configuring the range of the MLD snooping profile." ::= { mldSnoopMgt 20 } mldSnoopProfileRangeEntry OBJECT-TYPE SYNTAX MldSnoopProfileRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry for configuring the range of the MLD snooping profile." INDEX { mldSnoopProfileRangeProfileId, mldSnoopProfileRangeInetAddressType, mldSnoopProfileRangeStartInetAddress, mldSnoopProfileRangeEndInetAddress } ::= { mldSnoopProfileRangeTable 1 } MldSnoopProfileRangeEntry ::= SEQUENCE { mldSnoopProfileRangeProfileId Unsigned32, mldSnoopProfileRangeInetAddressType InetAddressType, mldSnoopProfileRangeStartInetAddress InetAddress, mldSnoopProfileRangeEndInetAddress InetAddress, mldSnoopProfileRangeAction INTEGER } mldSnoopProfileRangeProfileId OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is defined as mldSnoopProfileId." ::= { mldSnoopProfileRangeEntry 1 } mldSnoopProfileRangeInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type is associated with this agent. Only ipv6(2) type is supported." ::= { mldSnoopProfileRangeEntry 2 } mldSnoopProfileRangeStartInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The specified addresses in the start of the controlled IPv6 multicast addresses." ::= { mldSnoopProfileRangeEntry 3 } mldSnoopProfileRangeEndInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The specified addresses in the end of the controlled IPv6 multicast addresses." ::= { mldSnoopProfileRangeEntry 4 } mldSnoopProfileRangeAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The access mode of the MLD snooping profile." DEFVAL { deny } ::= { mldSnoopProfileRangeEntry 5 } mldSnoopFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in MLD filtering." ::= { mldSnoopMgt 21 } mldSnoopFilterPortEntry OBJECT-TYPE SYNTAX MldSnoopFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in MLD filtering." INDEX { mldSnoopFilterPortIndex } ::= { mldSnoopFilterPortTable 1 } MldSnoopFilterPortEntry ::= SEQUENCE { mldSnoopFilterPortIndex Unsigned32, mldSnoopFilterPortProfileId Integer32 } mldSnoopFilterPortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { mldSnoopFilterPortEntry 1 } mldSnoopFilterPortProfileId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The mldSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the mldSnoopProfileId object. If there is no corresponding entry in the mldSnoopProfileTable, then no association exists. In particular, if this value is zero, no associated profile will be generated, as zero is not a valid profile index." ::= { mldSnoopFilterPortEntry 2 } mldSnoopThrottlePortTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopThrottlePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in MLD throttling." ::= { mldSnoopMgt 22 } mldSnoopThrottlePortEntry OBJECT-TYPE SYNTAX MldSnoopThrottlePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in MLD throttling." INDEX { mldSnoopThrottlePortIndex } ::= { mldSnoopThrottlePortTable 1 } MldSnoopThrottlePortEntry ::= SEQUENCE { mldSnoopThrottlePortIndex Unsigned32, mldSnoopThrottlePortRunningStatus INTEGER, mldSnoopThrottlePortAction INTEGER, mldSnoopThrottlePortMaxGroups Integer32, mldSnoopThrottlePortCurrentGroups Integer32 } mldSnoopThrottlePortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB." ::= { mldSnoopThrottlePortEntry 1 } mldSnoopThrottlePortRunningStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Describes the running status of the MLD throttling to the switch. A value of true(1) indicates the MLD throttling mechanism is active. A value of false(2) indicates the MLD throttling mechanism is inactive." ::= { mldSnoopThrottlePortEntry 2 } mldSnoopThrottlePortAction OBJECT-TYPE SYNTAX INTEGER { replace(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action mode of the MLD throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an MLD report and the number of current joined multicast groups is equal to the maximum number of MLD groups that the interface can join. A value of deny(2) means to deny the MLD report request when an interface receives an MLD report and the number of current joined multicast groups is equal to the maximum number of MLD groups that the interface can join." DEFVAL { deny } ::= { mldSnoopThrottlePortEntry 3 } mldSnoopThrottlePortMaxGroups OBJECT-TYPE SYNTAX Integer32(0..256) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of MLD groups that the interface can join." ::= { mldSnoopThrottlePortEntry 4 } mldSnoopThrottlePortCurrentGroups OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of MLD groups that the interface has joined." ::= { mldSnoopThrottlePortEntry 5} mldSnoopClearDynamicGroups OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The current number of MLD groups that the interface has joined." ::= { mldSnoopMgt 23} mldSnoopVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MldSnoopVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of MLD Snooping service per port." ::= {mldSnoopMgt 24 } mldSnoopVlanEntry OBJECT-TYPE SYNTAX MldSnoopVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of MLD Snooping service per VLAN." INDEX { mldSnoopVlanIndex } ::= {mldSnoopVlanTable 1} MldSnoopVlanEntry ::= SEQUENCE { mldSnoopVlanIndex VlanIndex, mldSnoopVlanNumGroups Unsigned32, mldSnoopVlanNumJoinSend Unsigned32, mldSnoopVlanNumJoins Unsigned32, mldSnoopVlanNumJoinSuccess Unsigned32, mldSnoopVlanNumLeavesSend Unsigned32, mldSnoopVlanNumLeaves Unsigned32, mldSnoopVlanNumGeneralQuerySend Unsigned32, mldSnoopVlanNumGeneralQueryRecevied Unsigned32, mldSnoopVlanNumSepcificQuerySend Unsigned32, mldsnoopVlanNumSpecificQueryReceived Unsigned32, mldSnoopVlanNumInvalidReport Unsigned32, mldSnoopVlanClearStatistics TruthValue } mldSnoopVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN ID" ::= { mldSnoopVlanEntry 1 } mldSnoopVlanNumGroups OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current learned groups " ::= { mldSnoopVlanEntry 2 } mldSnoopVlanNumJoinSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join send." ::= { mldSnoopVlanEntry 3 } mldSnoopVlanNumJoins OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of join received " ::= { mldSnoopVlanEntry 4 } mldSnoopVlanNumJoinSuccess OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of jion success " ::= { mldSnoopVlanEntry 5 } mldSnoopVlanNumLeavesSend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave send." ::= { mldSnoopVlanEntry 6 } mldSnoopVlanNumLeaves OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of leave received " ::= { mldSnoopVlanEntry 7} mldSnoopVlanNumGeneralQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query send " ::= { mldSnoopVlanEntry 8} mldSnoopVlanNumGeneralQueryRecevied OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of general query received " ::= { mldSnoopVlanEntry 9} mldSnoopVlanNumSepcificQuerySend OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of specific query send" ::= { mldSnoopVlanEntry 10} mldsnoopVlanNumSpecificQueryReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sepcific query received " ::= { mldSnoopVlanEntry 11} mldSnoopVlanNumInvalidReport OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid report received" ::= { mldSnoopVlanEntry 12} mldSnoopVlanClearStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Clear this VLAN statistics" ::= { mldSnoopVlanEntry 13} -- -- dynamicArpInspectionMgt -- daiGlobal OBJECT IDENTIFIER ::= { dynamicArpInspectionMgt 1 } daiVlan OBJECT IDENTIFIER ::= { dynamicArpInspectionMgt 2 } daiInterface OBJECT IDENTIFIER ::= { dynamicArpInspectionMgt 3 } daiLog OBJECT IDENTIFIER ::= { dynamicArpInspectionMgt 4 } daiStatistics OBJECT IDENTIFIER ::= { dynamicArpInspectionMgt 5 } daiGlobalStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable dynamic ARP inspection. Set disabled(2) to disable dynamic ARP inspection." ::= { daiGlobal 1 } daiGlobalSrcMacValidation OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable validation of source MAC address. Set disabled(2) to disable validation of source MAC address." ::= { daiGlobal 2 } daiGlobalDestMacValidation OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable validation of destination MAC address. Set disabled(2) to disable validation of destination MAC address." ::= { daiGlobal 3 } daiGlobalIpAddrValidation OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable validation of IP address. Set disabled(2) to disable validation of IP address." ::= { daiGlobal 4 } daiGlobalLogNumber OBJECT-TYPE SYNTAX Integer32(0..256) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of log buffers for saving log message. The value 0 means not generating system messages." ::= { daiGlobal 5 } daiGlobalLogInterval OBJECT-TYPE SYNTAX Integer32(0..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the time interval for saving log messages." ::= { daiGlobal 6 } daiGlobalAdditionalValidStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The vaule of this object is disabled(2) when the status of daiGlobalSrcMacValidation, daiGlobalDestMacValidation, and daiGlobalIpAddrValidation are disabled; enabled(1) when one or more of these variables are enabled." ::= { daiGlobal 7 } daiGlobalIpAddrValidationAllowZeros OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable validation of IP address allow zeros. Set disabled(2) to disable validation of IP address allow zeros." ::= { daiGlobal 8 } daiVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF DaiVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains dynamic ARP inspection configurations for existing VLANs." ::= { daiVlan 1 } daiVlanEntry OBJECT-TYPE SYNTAX DaiVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance containing the configuration of dynamic ARP inspection for each existing VLAN." INDEX { daiVlanIndex } ::= { daiVlanTable 1 } DaiVlanEntry ::= SEQUENCE { daiVlanIndex VlanIndex, daiVlanStatus EnabledStatus, daiVlanArpAclName DisplayString, daiVlanArpAclStatus INTEGER } daiVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the VLAN ID on which dynamic ARP inspection is configured." ::= { daiVlanEntry 1 } daiVlanStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether dynamic ARP inspection is enabled in this VLAN." ::= { daiVlanEntry 2 } daiVlanArpAclName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the ARP ACL name bound to the interface. The default value of daiVlanArpAclStatus is dynamic(2)." ::= { daiVlanEntry 3 } daiVlanArpAclStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to static(1) means packets not matching the ACL are dropped. Set to dynamic(2) means packets not matching the ACL are validated by the DHCP snooping binding table. When daiVlanArpAclName is configured, the default value of daiVlanArpAclStatus is dynamic(2)." ::= { daiVlanEntry 4 } daiPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DaiPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing dynamic ARP inspection configurations for port interfaces." ::= { daiInterface 1 } daiPortEntry OBJECT-TYPE SYNTAX DaiPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance containing the configuration of dynamic ARP inspection at each port interface." INDEX { daiPortIfIndex } ::= { daiPortTable 1 } DaiPortEntry ::= SEQUENCE { daiPortIfIndex InterfaceIndex, daiPortTrustStatus EnabledStatus, daiPortRateLimit Unsigned32 } daiPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the port." ::= { daiPortEntry 1 } daiPortTrustStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the port is trusted for dynamic ARP inspection." ::= { daiPortEntry 2 } daiPortRateLimit OBJECT-TYPE SYNTAX Unsigned32(0..2048|'FFFFFFFF'h) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of rate limit threshold per second of disposing ARP messages. Set the value 0xFFFFFFFF as no rate limit." ::= { daiPortEntry 3 } daiLogTable OBJECT-TYPE SYNTAX SEQUENCE OF DaiLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing dynamic ARP inspection log information." ::= { daiLog 1 } daiLogEntry OBJECT-TYPE SYNTAX DaiLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance containing log information of dynamic ARP inspection at each VLAN interface." INDEX { daiLogIndex } ::= { daiLogTable 1 } DaiLogEntry ::= SEQUENCE { daiLogIndex Integer32, daiLogVlan VlanIndex, daiLogPort InterfaceIndex, daiLogSrcIpAddress IpAddress, daiLogDestIpAddress IpAddress, daiLogSrcMacAddress MacAddress, daiLogDestMacAddress MacAddress } daiLogIndex OBJECT-TYPE SYNTAX Integer32 (1..256) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the index of dynamic ARP inspection log information." ::= { daiLogEntry 1 } daiLogVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VLAN ID of dynamic ARP inspection log information." ::= { daiLogEntry 2 } daiLogPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ifIndex of dynamic ARP inspection log information." ::= { daiLogEntry 3 } daiLogSrcIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address of dynamic ARP inspection log information." ::= { daiLogEntry 4 } daiLogDestIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address of dynamic ARP inspection log information." ::= { daiLogEntry 5 } daiLogSrcMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source MAC address of dynamic ARP inspection log information." ::= { daiLogEntry 6 } daiLogDestMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination MAC address of dynamic ARP inspection log information." ::= { daiLogEntry 7 } daiTotalReceivedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets received before rate limiting." ::= { daiStatistics 1 } daiTotalDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets dropped due to rate limt." ::= { daiStatistics 2 } daiTotalProcessedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets processed by ARP inspection." ::= { daiStatistics 3 } daiTotalSrcMacDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets dropped by source MAC address validation." ::= { daiStatistics 4 } daiTotalDestMacDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets dropped by destination MAC address validation." ::= { daiStatistics 5 } daiTotalIpAddrDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets dropped by IP address validation." ::= { daiStatistics 6 } daiTotalArpAclDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets dropped by ARP ACL." ::= { daiStatistics 7 } daiTotalDhcpSnoopingDroppedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of ARP packets dropped by DHCP snooping." ::= { daiStatistics 8 } -- -- PPPoE Intermediate Agent -- pppoeiaGlobal OBJECT IDENTIFIER ::= { pppoeiaMgt 1 } pppoeiaGlobalStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable global status of PPPoE Intermediate Agent. Set disbaled(2) to disable global status of PPPoE Intermediate Agent." ::= { pppoeiaGlobal 1 } pppoeiaGlobalAccessNodeId OBJECT-TYPE SYNTAX DisplayString(SIZE(0..48)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies access node identifier. Use empty to revert to default value." ::= { pppoeiaGlobal 2 } pppoeiaGlobalOperAccessNodeId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The operational access node identifier." ::= { pppoeiaGlobal 3 } pppoeiaGlobalGenericErrorMsg OBJECT-TYPE SYNTAX DisplayString(SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies generic error message. Use empty to revert to default value." ::= { pppoeiaGlobal 4 } pppoeiaGlobalOperGenericErrorMsg OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The operational generic error message." ::= { pppoeiaGlobal 5 } pppoeiaGlobalClearStatisticsAction OBJECT-TYPE SYNTAX INTEGER { clear(1), noClear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear the counters of all interfaces. Set clear(1) to perform the clear operation. The value noClear(2) will always be displayed when reading." ::= { pppoeiaGlobal 6 } pppoeiaPortTable OBJECT-TYPE SYNTAX SEQUENCE OF PppoeiaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration in PPPoE Intermediate Agent." ::= { pppoeiaMgt 2 } pppoeiaPortEntry OBJECT-TYPE SYNTAX PppoeiaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration in PPPoE Intermediate Agent." INDEX { pppoeiaPortIndex } ::= { pppoeiaPortTable 1 } PppoeiaPortEntry ::= SEQUENCE { pppoeiaPortIndex InterfaceIndex, pppoeiaPortStatus EnabledStatus, pppoeiaPortTrustStatus EnabledStatus, pppoeiaPortVendorTagStrip EnabledStatus, pppoeiaPortCircuitId DisplayString, pppoeiaPortOperCircuitId DisplayString, pppoeiaPortRemoteId DisplayString, pppoeiaPortOperRemoteId DisplayString, pppoeiaPortRemoteIdDelimiterEnable EnabledStatus, pppoeiaPortRemoteIdDelimiterAscii Integer32 } pppoeiaPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { pppoeiaPortEntry 1 } pppoeiaPortStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to enable/disable PPPoE Intermediate Agent on interfaces." ::= { pppoeiaPortEntry 2 } pppoeiaPortTrustStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to enable/disable trust mode of PPPoE Intermediate Agent on interfaces." ::= { pppoeiaPortEntry 3 } pppoeiaPortVendorTagStrip OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to enable/disable stripping of vendor tag status of PPPoE Intermediate Agent on interfaces." ::= { pppoeiaPortEntry 4 } pppoeiaPortCircuitId OBJECT-TYPE SYNTAX DisplayString(SIZE(0..10)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies circuit ID of PPPoE Intermediate Agent on interfaces. Use empty to revert to default value." ::= { pppoeiaPortEntry 5 } pppoeiaPortOperCircuitId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The operational circuit ID of PPPoE Intermediate Agent on interfaces." ::= { pppoeiaPortEntry 6 } pppoeiaPortRemoteId OBJECT-TYPE SYNTAX DisplayString(SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies remote ID of PPPoE Intermediate Agent on interfaces. Use empty to revert to default value." ::= { pppoeiaPortEntry 7 } pppoeiaPortOperRemoteId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The operational remote ID of PPPoE Intermediate Agent on interfaces." ::= { pppoeiaPortEntry 8 } pppoeiaPortRemoteIdDelimiterEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to enable/disable delimiter for remote ID of PPPoE Intermediate Agent on interfaces." ::= { pppoeiaPortEntry 9 } pppoeiaPortRemoteIdDelimiterAscii OBJECT-TYPE SYNTAX Integer32(0..256) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the ASCII code of delimiter for remote ID of PPPoE Intermediate Agent on interfaces. Use 256 to revert to default value." ::= { pppoeiaPortEntry 10 } pppoeiaPortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF PppoeiaPortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port statistics in PPPoE Intermediate Agent." ::= { pppoeiaMgt 3 } pppoeiaPortStatsEntry OBJECT-TYPE SYNTAX PppoeiaPortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port statistics in PPPoE Intermediate Agent." INDEX { pppoeiaPortStatsIndex } ::= { pppoeiaPortStatsTable 1 } PppoeiaPortStatsEntry ::= SEQUENCE { pppoeiaPortStatsIndex InterfaceIndex, pppoeiaPortStatsRecvPkts Counter32, pppoeiaPortStatsRecvPadiPkts Counter32, pppoeiaPortStatsRecvPadoPkts Counter32, pppoeiaPortStatsRecvPadrPkts Counter32, pppoeiaPortStatsRecvPadsPkts Counter32, pppoeiaPortStatsRecvPadtPkts Counter32, pppoeiaPortStatsDropUntrustRespPkts Counter32, pppoeiaPortStatsDropUntrustReqPkts Counter32, pppoeiaPortStatsDropMalformedPkts Counter32, pppoeiaPortStatsClearAction INTEGER } pppoeiaPortStatsIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { pppoeiaPortStatsEntry 1 } pppoeiaPortStatsRecvPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of received packets of the interface." ::= { pppoeiaPortStatsEntry 2 } pppoeiaPortStatsRecvPadiPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of received PPPoE Active Discovery Initiation packets of the interface." ::= { pppoeiaPortStatsEntry 3 } pppoeiaPortStatsRecvPadoPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of received PPPoE Active Discovery Offer packets of the interface." ::= { pppoeiaPortStatsEntry 4 } pppoeiaPortStatsRecvPadrPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of received PPPoE Active Discovery Request packets of the interface." ::= { pppoeiaPortStatsEntry 5 } pppoeiaPortStatsRecvPadsPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of received PPPoE Active Discovery Session-confirmation packets of the interface." ::= { pppoeiaPortStatsEntry 6 } pppoeiaPortStatsRecvPadtPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of received PPPoE Active Discovery Terminate packets of the interface." ::= { pppoeiaPortStatsEntry 7 } pppoeiaPortStatsDropUntrustRespPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of response packets dropped because they were untrusted." ::= { pppoeiaPortStatsEntry 8 } pppoeiaPortStatsDropUntrustReqPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of request packets dropped because they were untrusted." ::= { pppoeiaPortStatsEntry 9 } pppoeiaPortStatsDropMalformedPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of malformed packets dropped because they were untrusted." ::= { pppoeiaPortStatsEntry 10 } pppoeiaPortStatsClearAction OBJECT-TYPE SYNTAX INTEGER { clear(1), noClear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear the counters of specified interface. Set clear(1) to perform the clear operation. The value noClear(2) will always be displayed when reading." ::= { pppoeiaPortStatsEntry 11 } -- -- time range -- timeRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF TimeRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for time range." ::= { timeRangeMgt 1 } timeRangeEntry OBJECT-TYPE SYNTAX TimeRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for time range." INDEX { timeRangeIndex } ::= { timeRangeTable 1 } TimeRangeEntry ::= SEQUENCE { timeRangeIndex Integer32, timeRangeName DisplayString, timeRangeStatus ValidStatus } timeRangeIndex OBJECT-TYPE SYNTAX Integer32 (0..49) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of time range entry." ::= { timeRangeEntry 1 } timeRangeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of time range entry." ::= { timeRangeEntry 2 } timeRangeStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry." ::= { timeRangeEntry 3 } timeRangePeriodicTable OBJECT-TYPE SYNTAX SEQUENCE OF TimeRangePeriodicEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for periodic time-range entries." ::= { timeRangeMgt 2 } timeRangePeriodicEntry OBJECT-TYPE SYNTAX TimeRangePeriodicEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for periodic time-range." INDEX { timeRangePeriodicTimeRangeIndex, timeRangePeriodicStartDaysOfTheWeek, timeRangePeriodicStartHours, timeRangePeriodicStartMinutes, timeRangePeriodicEndDaysOfTheWeek, timeRangePeriodicEndHours, timeRangePeriodicEndMinutes } ::= { timeRangePeriodicTable 1 } TimeRangePeriodicEntry ::= SEQUENCE { timeRangePeriodicTimeRangeIndex Integer32, timeRangePeriodicStartDaysOfTheWeek INTEGER, timeRangePeriodicStartHours Integer32, timeRangePeriodicStartMinutes Integer32, timeRangePeriodicEndDaysOfTheWeek INTEGER, timeRangePeriodicEndHours Integer32, timeRangePeriodicEndMinutes Integer32, timeRangePeriodicStatus ValidStatus } timeRangePeriodicTimeRangeIndex OBJECT-TYPE SYNTAX Integer32 (0..6) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of time range. The object should exist in timeRangeIndex of timeRangeTable." ::= { timeRangePeriodicEntry 1 } timeRangePeriodicStartDaysOfTheWeek OBJECT-TYPE SYNTAX INTEGER { sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6), daily(7), weekdays(8), weekend(9) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the start days-of-the-week of the periodic time-range entry. 1. If the start days-of-the-week is set to Sunday, Monday... or Saturday then the end days-of-the-week shall be set to Sunday, Monday..., or Saturday. 1-1. If the start time is equal to the end time (for example: 09:00 - 09:00), it means that the rule is active in the whole day. 1-2. If the end time is prior to the start time (for example: 05:00 - 01:00), it means that the rule is inactive from 01:01 to 04:59. 2. If the start days-of-the-week is set to Daily, Weekdays, or Weekend, then the end days-of-the-week shall be set the same as start, and the start time shall be before the end time." ::= { timeRangePeriodicEntry 2 } timeRangePeriodicStartHours OBJECT-TYPE SYNTAX Integer32(0..23) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the start hours of the periodic time-range entry." ::= { timeRangePeriodicEntry 3 } timeRangePeriodicStartMinutes OBJECT-TYPE SYNTAX Integer32(0..59) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the start minutess of the periodic time-range entry." ::= { timeRangePeriodicEntry 4 } timeRangePeriodicEndDaysOfTheWeek OBJECT-TYPE SYNTAX INTEGER { sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6), daily(7), weekdays(8), weekend(9) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the end days-of-the-week of the periodic time-range entry. 1. If the start days-of-the-week is set to Sunday, Monday... or Saturday then the end days-of-the-week shall be set to Sunday, Monday..., or Saturday. 1-1. If the start time is equal to the end time (for example: 09:00 - 09:00), it means that the rule is active in the whole day. 1-2. If the end time is prior to the start time (for example: 05:00 - 01:00), it means that the rule is inactive from 01:01 to 04:59. 2. If the start days-of-the-week is set to Daily, Weekdays, or Weekend, then the end days-of-the-week shall be set the same as start, and the start time shall be before the end time." ::= { timeRangePeriodicEntry 5 } timeRangePeriodicEndHours OBJECT-TYPE SYNTAX Integer32(0..23) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the end hours of the periodic time-range entry." ::= { timeRangePeriodicEntry 6 } timeRangePeriodicEndMinutes OBJECT-TYPE SYNTAX Integer32(0..59) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the end minutess of the periodic time-range entry." ::= { timeRangePeriodicEntry 7 } timeRangePeriodicStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an periodic entry. Setting this to invalid(2) destroys an periodic entry." ::= { timeRangePeriodicEntry 8 } timeRangeAbsoluteTable OBJECT-TYPE SYNTAX SEQUENCE OF TimeRangeAbsoluteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for absolute time-range entries." ::= { timeRangeMgt 3 } timeRangeAbsoluteEntry OBJECT-TYPE SYNTAX TimeRangeAbsoluteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for absolute time-range." INDEX { timeRangeAbsoluteTimeRangeIndex, timeRangeAbsoluteStartYears, timeRangeAbsoluteStartMonths, timeRangeAbsoluteStartDays, timeRangeAbsoluteStartHours, timeRangeAbsoluteStartMinutes, timeRangeAbsoluteEndYears, timeRangeAbsoluteEndMonths, timeRangeAbsoluteEndDays, timeRangeAbsoluteEndHours, timeRangeAbsoluteEndMinutes } ::= { timeRangeAbsoluteTable 1 } TimeRangeAbsoluteEntry ::= SEQUENCE { timeRangeAbsoluteTimeRangeIndex Integer32, timeRangeAbsoluteStartYears Integer32, timeRangeAbsoluteStartMonths Integer32, timeRangeAbsoluteStartDays Integer32, timeRangeAbsoluteStartHours Integer32, timeRangeAbsoluteStartMinutes Integer32, timeRangeAbsoluteEndYears Integer32, timeRangeAbsoluteEndMonths Integer32, timeRangeAbsoluteEndDays Integer32, timeRangeAbsoluteEndHours Integer32, timeRangeAbsoluteEndMinutes Integer32, timeRangeAbsoluteStatus ValidStatus } timeRangeAbsoluteTimeRangeIndex OBJECT-TYPE SYNTAX Integer32 (0..49) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of time range. The object should exist in timeRangeIndex of timeRangeTable." ::= { timeRangeAbsoluteEntry 1 } timeRangeAbsoluteStartYears OBJECT-TYPE SYNTAX Integer32(2013..2037|65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the start years of the absolute time-range entry. 65535 means don't care." ::= { timeRangeAbsoluteEntry 2 } timeRangeAbsoluteStartMonths OBJECT-TYPE SYNTAX Integer32(1..12|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the start months of the absolute time-range entry. 255 means don't care." ::= { timeRangeAbsoluteEntry 3 } timeRangeAbsoluteStartDays OBJECT-TYPE SYNTAX Integer32(1..31|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the start days of the absolute time-range entry. 255 means don't care." ::= { timeRangeAbsoluteEntry 4 } timeRangeAbsoluteStartHours OBJECT-TYPE SYNTAX Integer32(0..23|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the start hours of the absolute time-range entry.\ 255 means don't care." ::= { timeRangeAbsoluteEntry 5 } timeRangeAbsoluteStartMinutes OBJECT-TYPE SYNTAX Integer32(0..59|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the start minutes of the absolute time-range entry.\ 255 means don't care." ::= { timeRangeAbsoluteEntry 6 } timeRangeAbsoluteEndYears OBJECT-TYPE SYNTAX Integer32(2013..2037|65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the end years of the absolute time-range entry. 65535 means don't care." ::= { timeRangeAbsoluteEntry 7 } timeRangeAbsoluteEndMonths OBJECT-TYPE SYNTAX Integer32(1..12|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the end months of the absolute time-range entry. 255 means don't care." ::= { timeRangeAbsoluteEntry 8 } timeRangeAbsoluteEndDays OBJECT-TYPE SYNTAX Integer32(1..31|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the end days of the absolute time-range entry. 255 means don't care." ::= { timeRangeAbsoluteEntry 9 } timeRangeAbsoluteEndHours OBJECT-TYPE SYNTAX Integer32(0..23|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the end hours of the absolute time-range entry.\ 255 means don't care." ::= { timeRangeAbsoluteEntry 10 } timeRangeAbsoluteEndMinutes OBJECT-TYPE SYNTAX Integer32(0..59|255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the end minutes of the absolute time-range entry.\ 255 means don't care." ::= { timeRangeAbsoluteEntry 11 } timeRangeAbsoluteStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this to valid(1) creates an absolute entry. Setting this to invalid(2) destroys an absolute entry." ::= { timeRangeAbsoluteEntry 12 } -- -- erpsMgt -- -- Management for Ethernet Ring Protection Switching(ERPS) protocol. erpsGlobalStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the ERPS function for an entire switch. Note that the ERPS domain will not take effect unless it becomes active and the global status is enabled." ::= { erpsMgt 1 } erpsGlobalClearStatisticsAction OBJECT-TYPE SYNTAX INTEGER { clear(1), noClear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear the counters of all ERPS domains. Set to clear(1) to perform the clear operation. The value noClear(2) will always be displayed when reading." ::= { erpsMgt 3 } erpsDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF ErpsDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for ERPS domain configuration." ::= { erpsMgt 2 } erpsDomainEntry OBJECT-TYPE SYNTAX ErpsDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for ERPS domain configuration." INDEX { erpsDomainIndex } ::= { erpsDomainTable 1 } ErpsDomainEntry ::= SEQUENCE { erpsDomainIndex Integer32, erpsDomainName DisplayString, erpsDomainMegLevel INTEGER, erpsDomainNodeId MacAddress, erpsDomainWestRingPort Integer32, erpsDomainEastRingPort Integer32, erpsDomainRplPort INTEGER, erpsDomainGuardTimer Integer32, erpsDomainHoldoffTimer Integer32, erpsDomainWtrTimer Integer32, erpsDomainControlVlanID Integer32, erpsDomainNodeState INTEGER, erpsDomainWestRingPortState INTEGER, erpsDomainEastRingPortState INTEGER, erpsDomainRowStatus RowStatus, erpsDomainMajorDomainIndex Integer32, erpsDomainPropagateTC INTEGER, erpsDomainWestMepId Integer32, erpsDomainEastMepId Integer32, erpsDomainNonErpsDevProtect INTEGER, erpsDomainNodeType INTEGER, erpsDomainNonRevertive INTEGER, erpsDomainRapsDefMac INTEGER, erpsDomainRapsWithoutVc INTEGER, erpsDomainVersion INTEGER, erpsDomainForcedSwitch INTEGER, erpsDomainManualSwitch INTEGER, erpsDomainClear INTEGER, erpsDomainStatsClearAction INTEGER, erpsDomainWtbTimer Integer32, erpsDomainWtrExpire Integer32, erpsDomainWtbExpire Integer32, erpsDomainWestRingPortSf INTEGER, erpsDomainEastRingPortSf INTEGER, erpsDomainMultiRplOwnerWarn INTEGER } erpsDomainIndex OBJECT-TYPE SYNTAX Integer32(1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the erpsDomainTable." ::= { erpsDomainEntry 1 } erpsDomainName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..12)) MAX-ACCESS read-create STATUS current DESCRIPTION "The domain name that uniquely identifies an entry in the erpsDomainTable." ::= { erpsDomainEntry 2 } erpsDomainMegLevel OBJECT-TYPE SYNTAX INTEGER(0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Configures the maintenance entity group (MEG) level which is used to provide a communication channel for ring automatic protection switching (R-APS) information." ::= { erpsDomainEntry 3 } erpsDomainNodeId OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Configures the node id whcih is a MAC address unique to the ring node." ::= { erpsDomainEntry 4 } erpsDomainWestRingPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Each node on the ring connects to the ring through two ports. As part of the protection switching scheme, one port can be configured as the west port for the specified domain. The east port and west port can not be configured as the same port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB. A value of 0 means no west ring port configured for this domain." ::= { erpsDomainEntry 5 } erpsDomainEastRingPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Each node on the ring connects to the ring through two ports. As part of the protection switching scheme, one port can be configured as the east port for the specified domain. The east port and west port can not be configured as the same port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB. A value of 0 means no east ring port configured for this domain." ::= { erpsDomainEntry 6 } erpsDomainRplPort OBJECT-TYPE SYNTAX INTEGER { none(1), west(2), east(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value displays the port for ring protection link which under normal conditions, i.e., without any failure or request, is blocked for traffic channel, to prevent the formation of loops." ::= { erpsDomainEntry 8 } erpsDomainGuardTimer OBJECT-TYPE SYNTAX Integer32 (10..2000) MAX-ACCESS read-create STATUS current DESCRIPTION "Configures the value of the guard timer which is used to prevent ring nodes from receiving outdated R-APS messages. The range is in 10 ms steps between 10 ms and 2 seconds, with a default value of 500 ms." DEFVAL { 500 } ::= { erpsDomainEntry 9 } erpsDomainHoldoffTimer OBJECT-TYPE SYNTAX Integer32 (0..10000) MAX-ACCESS read-create STATUS current DESCRIPTION "Configures the value of the holdoff timer which is used to prevent reporting error event immediately to protection switching if the provisioned holdoff timer value is non-zero. The range is in 100 ms steps between 0 and 10 seconds, with a default value of 0 ms." DEFVAL { 0 } ::= { erpsDomainEntry 10 } erpsDomainWtrTimer OBJECT-TYPE SYNTAX Integer32 (5..12) MAX-ACCESS read-create STATUS current DESCRIPTION "Configures the value of the wait-to-restore timer which is used by the RPL owner node to prevent frequent switching operations that may be caused by intermittent failures. The range is in 1 minute steps between 5 and 12 minutes with a default value of 5 minutes. This object will not take effect for the non RPL owner node." DEFVAL { 5 } ::= { erpsDomainEntry 11 } erpsDomainControlVlanID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB. Configures one control VLAN for each ERPS domain. The control VLAN is used only to send and receive ERPS message. A control VLAN can not belong to more than one ERPS domain. A value of 0 means no control VLAN configured for this domain." ::= { erpsDomainEntry 12 } erpsDomainNodeState OBJECT-TYPE SYNTAX INTEGER { init(1), idle(2), protection(3), manualSwitch(4), forcedSwitch(5), pending(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value displays the node's current state. It displays one of the following states (1) init -- The node is in the init state. (The node state will stay in init state if global status or domain status is not enabled.) (2) idle -- The node is in idle state (i.e., no detected failures, and receiving only 'NR, RB' R-APS frames). (3) protection -- The node is in protection state. (4) manualSwitch -- The node is in manual switch state. (5) forcedSwitch -- The node is in forced switch state. (6) pending -- The node is in pending state." ::= { erpsDomainEntry 13 } erpsDomainWestRingPortState OBJECT-TYPE SYNTAX INTEGER { unknown(1), blocking(2), forwarding(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value displays the west ring port's current state. It displays one of the following states (1) unknown -- The port's current state is unknown. (The port's current state will stay in unknown state if the node's current state is in init state.) (2) blocking -- The transmission and reception of traffic are blocked. (3) forwarding -- The traffic can be transmitted and received normally." ::= { erpsDomainEntry 14 } erpsDomainEastRingPortState OBJECT-TYPE SYNTAX INTEGER { unknown(1), blocking(2), forwarding(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value displays the east ring port's current state. It displays one of the following states (1) unknown -- The port's current state is unknown. (The port's current state will stay in unknown state if the node's current state is in init state.) (2) blocking -- The transmission and reception of traffic are blocked. (3) forwarding -- The traffic can be transmitted and received normally." ::= { erpsDomainEntry 15 } erpsDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB. Note that other objects can not be modified when the status is active." ::= { erpsDomainEntry 16 } erpsDomainMajorDomainIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An index that uniquely identifies an entry in the erpsDomainTable. A value of 0 means this domain has no major domain. Notes: This objest can not be configured if erpsDomainRingPortEast has a vaule other than 0." ::= { erpsDomainEntry 17 } erpsDomainPropagateTC OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to enabled(1) to transmit topology change signal to the major domain. It will not take effect, if erpsDomainMajorDomainIndex has a value of 0." ::= { erpsDomainEntry 18 } erpsDomainWestMepId OBJECT-TYPE SYNTAX Integer32 (0..8191) MAX-ACCESS read-create STATUS current DESCRIPTION "Configures a CFM Down MEP on west ring port. A down MEP can be uniquely select by given a MEPID, domain's MEG level, and domain's control VLAN ID. A value of 0 means no west MEP is not configured for this domain." ::= { erpsDomainEntry 20 } erpsDomainEastMepId OBJECT-TYPE SYNTAX Integer32 (0..8191) MAX-ACCESS read-create STATUS current DESCRIPTION "Configures a CFM Down MEP on east ring port. A down MEP can be uniquely select by given a MEPID, domain's MEG level, and domain's control VLAN ID. A value of 0 means no east MEP is not configured for this domain." ::= { erpsDomainEntry 21 } erpsDomainNonErpsDevProtect OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to enabled(1) to use non-standard protection mechanism for network containing non-ERPS devices." ::= { erpsDomainEntry 22 } erpsDomainNodeType OBJECT-TYPE SYNTAX INTEGER { none(1), owner(2), neighbor(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to none(1) to make this node act as a normal node. Set to owner(2) to make this node act as an RPL owner. Set to neighbor(3) to make this node act as an RPL neighbor." ::= { erpsDomainEntry 23 } erpsDomainNonRevertive OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to enabled(1) to enable non-revertive mode operation." ::= { erpsDomainEntry 24 } erpsDomainRapsDefMac OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to enabled(1) to use R-APS default MAC." ::= { erpsDomainEntry 25 } erpsDomainRapsWithoutVc OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to enabled(1) to enable R-APS sub ring without virtual-channel for a sub domain." ::= { erpsDomainEntry 26 } erpsDomainVersion OBJECT-TYPE SYNTAX INTEGER { v1(1), v2(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to v2(2) to enable ERPS v2 operation." DEFVAL { 2 } ::= { erpsDomainEntry 27 } erpsDomainForcedSwitch OBJECT-TYPE SYNTAX INTEGER { none(1), west(2), east(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to west(2) to perform the forced switch command on west ring port of specified domain. Set to east(3) to perform the forced switch command on east ring port of specified domain. The value none(1) will be displayed if no forced switch command is issued on local node." ::= { erpsDomainEntry 28 } erpsDomainManualSwitch OBJECT-TYPE SYNTAX INTEGER { none(1), west(2), east(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to west(2) to perform the manual switch command on west ring port of specified domain. Set to east(3) to perform the manual switch command on east ring port of specified domain. The value none(1) will be displayed if no manual switch command is issued on local node." ::= { erpsDomainEntry 29 } erpsDomainClear OBJECT-TYPE SYNTAX INTEGER { clear(1), noClear(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set to clear(1) to perform the clear command on specified domain. The value noClear(2) will always be displayed when reading." ::= { erpsDomainEntry 30 } erpsDomainStatsClearAction OBJECT-TYPE SYNTAX INTEGER { clear(1), noClear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to clear the counters of specified domain. Set to clear(1) to perform the clear operation. The value noClear(2) will always be displayed when reading." ::= { erpsDomainEntry 31 } erpsDomainWtbTimer OBJECT-TYPE SYNTAX Integer32 (5010..7000) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the value of the wait-to-block timer in ms which is used by the RPL owner node when recovering from an operator command (i.e. FS or MS). This object will not take effect for a non RPL owner node." ::= { erpsDomainEntry 32 } erpsDomainWtbExpire OBJECT-TYPE SYNTAX Integer32 (0..7000) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the time remaining in ms until the wait-to-block timer countdown expires. A value of 0 means no countdown is running." ::= { erpsDomainEntry 33 } erpsDomainWtrExpire OBJECT-TYPE SYNTAX Integer32 (0..720) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the time remaining in seconds until the wait-to-restore timer countdown expires. A value of 0 means no countdown is running." ::= { erpsDomainEntry 34 } erpsDomainWestRingPortSf OBJECT-TYPE SYNTAX INTEGER { none(1), detected(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value displays the west ring port's current SF state. It displays one of the following states (1) none -- No SF is detected. (2) detected -- SF is detected." ::= { erpsDomainEntry 35 } erpsDomainEastRingPortSf OBJECT-TYPE SYNTAX INTEGER { none(1), detected(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value displays the east ring port's current SF state. It displays one of the following states (1) none -- No SF is detected. (2) detected -- SF is detected." ::= { erpsDomainEntry 36 } erpsDomainMultiRplOwnerWarn OBJECT-TYPE SYNTAX INTEGER { none(1), detected(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value displays the multiple PPL owner warning state. It displays one of the following states (1) none -- No multiple PPL owner warning is detected. (2) detected -- Multiple RPL owner warning is detected." ::= { erpsDomainEntry 37 } erpsPortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ErpsPortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port statistics in ERPS." ::= { erpsMgt 4 } erpsPortStatsEntry OBJECT-TYPE SYNTAX ErpsPortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port statistics in ERPS." INDEX { erpsPortStatsDomainIndex, erpsPortStatsPortIndex } ::= { erpsPortStatsTable 1 } ErpsPortStatsEntry ::= SEQUENCE { erpsPortStatsDomainIndex Integer32, erpsPortStatsPortIndex INTEGER, erpsPortStatsLocalSfCount Counter32, erpsPortStatsLocalClrSfCount Counter32, erpsPortStatsSentSfPkts Counter32, erpsPortStatsSentNrPkts Counter32, erpsPortStatsSentNrRbPkts Counter32, erpsPortStatsSentFsPkts Counter32, erpsPortStatsSentMsPkts Counter32, erpsPortStatsSentEventPkts Counter32, erpsPortStatsSentHealthPkts Counter32, erpsPortStatsRecvSfPkts Counter32, erpsPortStatsRecvNrPkts Counter32, erpsPortStatsRecvNrRbPkts Counter32, erpsPortStatsRecvFsPkts Counter32, erpsPortStatsRecvMsPkts Counter32, erpsPortStatsRecvEventPkts Counter32, erpsPortStatsRecvHealthPkts Counter32, erpsPortStatsIgnoreSfPkts Counter32, erpsPortStatsIgnoreNrPkts Counter32, erpsPortStatsIgnoreNrRbPkts Counter32, erpsPortStatsIgnoreFsPkts Counter32, erpsPortStatsIgnoreMsPkts Counter32, erpsPortStatsIgnoreEventPkts Counter32, erpsPortStatsIgnoreHealthPkts Counter32 } erpsPortStatsDomainIndex OBJECT-TYPE SYNTAX Integer32(1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the erpsDomainTable." ::= { erpsPortStatsEntry 1 } erpsPortStatsPortIndex OBJECT-TYPE SYNTAX INTEGER { west(1), east(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the port in an ERPS domain. The value west(1) means the west ring port. The value east(2) means the east ring port." ::= { erpsPortStatsEntry 2 } erpsPortStatsLocalSfCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of local SF events that occurred on this ring port." ::= { erpsPortStatsEntry 3 } erpsPortStatsLocalClrSfCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of local Clear SF events that occurred on this ring port." ::= { erpsPortStatsEntry 4 } erpsPortStatsSentSfPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS SF messages sent via this ring port (not including the forwarded ones)." ::= { erpsPortStatsEntry 5 } erpsPortStatsSentNrPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS NR messages sent via this ring port (not including the forwarded ones)." ::= { erpsPortStatsEntry 6 } erpsPortStatsSentNrRbPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS NR-RB messages sent via this ring port (not including the forwarded ones)." ::= { erpsPortStatsEntry 7 } erpsPortStatsSentFsPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS FS messages sent via this ring port (not including the forwarded ones)." ::= { erpsPortStatsEntry 8 } erpsPortStatsSentMsPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS MS messages sent via this ring port (not including the forwarded ones)." ::= { erpsPortStatsEntry 9 } erpsPortStatsSentEventPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS EVENT messages sent via this ring port (not including the forwarded ones)." ::= { erpsPortStatsEntry 10 } erpsPortStatsSentHealthPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of non-standard health-check messages sent via this ring port (not including the forwarded ones)." ::= { erpsPortStatsEntry 11 } erpsPortStatsRecvSfPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS SF messages received via this ring port (not including the ignored ones)." ::= { erpsPortStatsEntry 12 } erpsPortStatsRecvNrPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS NR messages received via this ring port (not including the ignored ones)." ::= { erpsPortStatsEntry 13 } erpsPortStatsRecvNrRbPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS NR-RB messages received via this ring port (not including the ignored ones)." ::= { erpsPortStatsEntry 14 } erpsPortStatsRecvFsPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS FS messages received via this ring port (not including the ignored ones)." ::= { erpsPortStatsEntry 15 } erpsPortStatsRecvMsPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS MS messages received via this ring port (not including the ignored ones)." ::= { erpsPortStatsEntry 16 } erpsPortStatsRecvEventPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS EVENT messages received via this ring port (not including the ignored ones)." ::= { erpsPortStatsEntry 17 } erpsPortStatsRecvHealthPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of non-standard health-check messages received via this ring port (not including the ignored ones)." ::= { erpsPortStatsEntry 18 } erpsPortStatsIgnoreSfPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS SF messages ignored by this ring port because they have been timed out or for other reasons." ::= { erpsPortStatsEntry 19 } erpsPortStatsIgnoreNrPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS NR messages ignored by this ring port because they have been timed out or for other reasons." ::= { erpsPortStatsEntry 20 } erpsPortStatsIgnoreNrRbPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS NR-RB messages ignored by this ring port because they have been timed out or for other reasons." ::= { erpsPortStatsEntry 21 } erpsPortStatsIgnoreFsPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS FS messages ignored by this ring port because they have been timed out or for other reasons." ::= { erpsPortStatsEntry 22 } erpsPortStatsIgnoreMsPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS MS messages ignored by this ring port because they have been timed out or for other reasons." ::= { erpsPortStatsEntry 23 } erpsPortStatsIgnoreEventPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of R-APS EVENT messages ignored by this ring port because they have been timed out or for other reasons." ::= { erpsPortStatsEntry 24 } erpsPortStatsIgnoreHealthPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of non-standard health-check messages ignored by this ring port because they have been timed out or for other reasons." ::= { erpsPortStatsEntry 25 } -- -- IPv6 RA Guard -- ipv6RaGuardPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv6RaGuardPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for IPv6 RA Guard port configuration." ::= { ipv6RaGuardMgt 1 } ipv6RaGuardPortEntry OBJECT-TYPE SYNTAX Ipv6RaGuardPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for IPv6 RA Guard port configuration." INDEX { ipv6RaGuardPortIndex } ::= { ipv6RaGuardPortTable 1 } Ipv6RaGuardPortEntry ::= SEQUENCE { ipv6RaGuardPortIndex InterfaceIndex, ipv6RaGuardPortStatus INTEGER } ipv6RaGuardPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { ipv6RaGuardPortEntry 1 } ipv6RaGuardPortStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "A value of enabled (1) indicates that IPv6 RA Guard feature is enabled on interfaces. A value of disabled (2) indicates that the feature is disabled." ::= { ipv6RaGuardPortEntry 2 } -- -- lbdMgt -- lbdGlobal OBJECT IDENTIFIER ::= { lbdMgt 1 } lbdInterface OBJECT IDENTIFIER ::= { lbdMgt 2 } lbdGlobalStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set enabled(1) to enable global LBD status. Set disabled(2) to disable global LBD status." ::= { lbdGlobal 1 } lbdTransmitInterval OBJECT-TYPE SYNTAX Unsigned32(1..32767) MAX-ACCESS read-write STATUS current DESCRIPTION "The transmission interval for LBD control frames." ::= { lbdGlobal 2 } lbdRecoverTime OBJECT-TYPE SYNTAX Unsigned32(0|60..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The recover time used by LBD auto recovery mechanism. A value of 0 disables auto recovery." ::= { lbdGlobal 3 } lbdMode OBJECT-TYPE SYNTAX INTEGER { port-based(1), vlan-based(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The detection mode of LBD." ::= { lbdGlobal 4 } lbdAction OBJECT-TYPE SYNTAX INTEGER { none(1), shutdown(2), block(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The protection action of LBD." ::= { lbdGlobal 5 } lbdTrap OBJECT-TYPE SYNTAX INTEGER { none(1), detect(2), recover(3), both(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The kind of SNMP traps for LBD will be sent." ::= { lbdGlobal 6 } lbdPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LbdPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing LBD configurations for all interfaces." ::= { lbdInterface 1 } lbdPortEntry OBJECT-TYPE SYNTAX LbdPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance containing the configuration of LBD at each interface." INDEX { lbdPortIfIndex } ::= { lbdPortTable 1 } LbdPortEntry ::= SEQUENCE { lbdPortIfIndex InterfaceIndex, lbdPortAdminState INTEGER, lbdPortOperState INTEGER, lbdPortLoopedVlan OCTET STRING } lbdPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the port." ::= { lbdPortEntry 1 } lbdPortAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The LBD administrative port status." ::= { lbdPortEntry 2 } lbdPortOperState OBJECT-TYPE SYNTAX INTEGER { normal(1), looped(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The LBD operative port status." ::= { lbdPortEntry 3 } lbdPortLoopedVlan OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The list of VLANs on which loopback is detected. Only when oper state is looped and mode is VLAN-based, the value is nonzero." ::= { lbdPortEntry 4 } -- -- udldMgt -- udldGlobalMessageInterval OBJECT-TYPE SYNTAX INTEGER(7..90) MAX-ACCESS read-write STATUS current DESCRIPTION "The message interval (in seconds) between UDLD probe messages on ports that are in advertisement phase and are determined to be bidirectional." DEFVAL { 15 } ::= { udldMgt 1 } udldGlobalDetectionInterval OBJECT-TYPE SYNTAX INTEGER(5..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The detection interval (in seconds) used for UDLD detection process." DEFVAL { 5 } ::= { udldMgt 4 } udldGlobalRecoveryInterval OBJECT-TYPE SYNTAX INTEGER(30..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "The recovery interval (in seconds) used to recover interface shut down by UDLD automatically." DEFVAL { 300 } ::= { udldMgt 5 } udldGlobalRecovery OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to enable/disable auto recovery feature." DEFVAL { disabled } ::= { udldMgt 6 } udldPortTable OBJECT-TYPE SYNTAX SEQUENCE OF UdldPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for port configuration of UDLD." ::= { udldMgt 2 } udldPortEntry OBJECT-TYPE SYNTAX UdldPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry for port configuration of UDLD." INDEX { udldPortIndex } ::= { udldPortTable 1 } UdldPortEntry ::= SEQUENCE { udldPortIndex InterfaceIndex, udldPortStatus EnabledStatus, udldPortAggressiveStatus EnabledStatus, udldPortOperState INTEGER, udldPortPortState INTEGER, udldPortOperMessageInterval INTEGER, udldPortOperTimeout INTEGER, udldPortNeighborDevCount INTEGER } udldPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The port (excluding trunk and trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { udldPortEntry 1 } udldPortStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to enable/disable UDLD on this interface." ::= { udldPortEntry 2 } udldPortAggressiveStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to enable/disable aggressive mode of UDLD on this interface." ::= { udldPortEntry 3 } udldPortOperState OBJECT-TYPE SYNTAX INTEGER { disabled(1), linkDown(2), linkUp(3), advertisement(4), detection(5), disabledPort(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational state of UDLD on this interface." ::= { udldPortEntry 4 } udldPortPortState OBJECT-TYPE SYNTAX INTEGER { unknown(1), neighborsEchoIsEmpty(2), bidirectional(3), mismatchWithneighborStateReported(4), transmitToReceiveLoop(5), unidirectional(6), aggressiveModeFailure(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port state of UDLD on this interface." ::= { udldPortEntry 5 } udldPortOperMessageInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The operational message interval (in seconds) used by UDLD on this interface." ::= { udldPortEntry 6 } udldPortOperTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The operational timeout interval (in seconds) used by UDLD to decide the basic length of the detection phase on this interface." ::= { udldPortEntry 7 } udldPortNeighborDevCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbor devices discovered on this interface." ::= { udldPortEntry 8 } udldPortNeighborDevTable OBJECT-TYPE SYNTAX SEQUENCE OF UdldPortNeighborDevEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of neighbor devices discovered by UDLD for each interface." ::= { udldMgt 3 } udldPortNeighborDevEntry OBJECT-TYPE SYNTAX UdldPortNeighborDevEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the information of a neighbor device." INDEX { udldPortNeighborDevPortIndex, udldPortNeighborDevIndex } ::= { udldPortNeighborDevTable 1 } UdldPortNeighborDevEntry ::= SEQUENCE { udldPortNeighborDevPortIndex InterfaceIndex, udldPortNeighborDevIndex Integer32, udldPortNeighborDevDevID DisplayString, udldPortNeighborDevPortID DisplayString, udldPortNeighborDevDevName DisplayString, udldPortNeighborDevNeighborState INTEGER, udldPortNeighborDevExpire INTEGER, udldPortNeighborDevMessageInterval INTEGER, udldPortNeighborDevTimeout INTEGER } udldPortNeighborDevPortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port (excluding trunk and trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB." ::= { udldPortNeighborDevEntry 1 } udldPortNeighborDevIndex OBJECT-TYPE SYNTAX Integer32(1..500) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the nieghbor device discovered by UDLD on a port interface." ::= { udldPortNeighborDevEntry 2 } udldPortNeighborDevDevID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The device ID of this neighbor device." ::= { udldPortNeighborDevEntry 3 } udldPortNeighborDevPortID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The port ID of this neighbor device." ::= { udldPortNeighborDevEntry 4 } udldPortNeighborDevDevName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The device name of this neighbor device." ::= { udldPortNeighborDevEntry 5 } udldPortNeighborDevNeighborState OBJECT-TYPE SYNTAX INTEGER { unknown(1), neighborsEchoIsEmpty(2), bidirectional(3), mismatchWithneighborStateReported(4), unidirectional(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The neighbor state of this neighbor device." ::= { udldPortNeighborDevEntry 6 } udldPortNeighborDevExpire OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time remaining (in seconds) before this entry should expire. Whenever this period expires, this entry will be removed." ::= { udldPortNeighborDevEntry 7 } udldPortNeighborDevMessageInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The message interval (in seconds) of this neighbor device." ::= { udldPortNeighborDevEntry 8 } udldPortNeighborDevTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The timeout interval (in seconds) of this neighbor device." ::= { udldPortNeighborDevEntry 9 } -- udpHelperMgt Table udpHelperStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Set this variable to enabled(1) to enable UDP helper. Set this variable to disabled(2) to disable UDP helper." DEFVAL { disabled } ::= { udpHelperMgt 1 } udpHelperForwardProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF UdpHelperForwardProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To specify which UDP ports the switch forwards when forwarding UDP broadcast packets." ::= { udpHelperMgt 2 } udpHelperForwardProtocolEntry OBJECT-TYPE SYNTAX UdpHelperForwardProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of udpHelperForwardProtocolTable." INDEX { udpHelperForwardProtocolPort } ::= { udpHelperForwardProtocolTable 1 } UdpHelperForwardProtocolEntry ::= SEQUENCE { udpHelperForwardProtocolPort Integer32, udpHelperForwardProtocolStatus ValidStatus } udpHelperForwardProtocolPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port number of the UDP protocol. Adding a helper address by udpHelperInetAddrTable causes the software to forward UDP broadcast packets. By this table, you can specify exactly which types of UDP broadcast packets you would like to have forwarded." ::= { udpHelperForwardProtocolEntry 1 } udpHelperForwardProtocolStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Set this variable to valid(1) to enable forwarding of packets. Set this variable to invalid(2) to disable forwarding of packets." ::= { udpHelperForwardProtocolEntry 2 } udpHelperInetAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF UdpHelperInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "To forward UDP broadcasts, including BOOTP, received on an interface. After configuring an UDP helper address on an interface, the UDP broadcast packets on this network to which this interface is attached will be sent to the helper. Combined with the configuration of udpHelperForwardProtocolTable, it allows you to control which kind of broadcast packets can be forwarded. One common application that requires helper addresses is Dynamic Host Configuration Protocol (DHCP), which is defined in RFC 1531. To enable BOOTP or DHCP broadcast forwarding for a set of clients, configure a helper address on the router interface connected to the client. The helper address should specify the address of the BOOTP or DHCP server. If you have multiple servers, you can configure one helper address for each server." ::= { udpHelperMgt 3 } udpHelperInetAddrEntry OBJECT-TYPE SYNTAX UdpHelperInetAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of udpHelperInetAddrTable." INDEX { udpHelperInetAddrVlanIndex, udpHelperInetAddrType, IMPLIED udpHelperInetAddr } ::= { udpHelperInetAddrTable 1 } UdpHelperInetAddrEntry ::= SEQUENCE { udpHelperInetAddrVlanIndex VlanIndex, udpHelperInetAddrType InetAddressType, udpHelperInetAddr InetAddress, udpHelperInetAddrStatus ValidStatus } udpHelperInetAddrVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN-ID or other identifier refering to this VLAN. Based on dot1qVlanIndex in the Q-BRIDGE-MIB." ::= { udpHelperInetAddrEntry 1 } udpHelperInetAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of the helper address." ::= { udpHelperInetAddrEntry 2 } udpHelperInetAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Internet address of the helper address." ::= { udpHelperInetAddrEntry 3 } udpHelperInetAddrStatus OBJECT-TYPE SYNTAX ValidStatus MAX-ACCESS read-create STATUS current DESCRIPTION "To forward UDP broadcasts, including BOOTP, received from the specified interface, to the specified address. Set this variable to valid(1) to enable forwarding of packets. Set this variable to invalid(2) to disable forwarding of packets. All of the following conditions must be met in order for a User Datagram Protocol (UDP) or IP packet to be helped: 1. The MAC address of the received frame must be all-ones broadcast address (FF-FF-FF-FF-FF-FF). 2. The IP destination address must be one of the following: 1) all-ones broadcast (255.255.255.255) 2) subnet broadcast for the receiving interface 3. The IP protocol must be UDP (17). 4. The UDP destination port must be TFTP, Domain Name System (DNS), Time, NetBIOS, BOOTP or DHCP packet, or a UDP port specified by the udpHelperForwardTable." ::= { udpHelperInetAddrEntry 4 } -- -- dhcpv6SnoopMgt -- -- Management of DHCPv6 snooping. dhcpv6SnoopGlobal OBJECT IDENTIFIER ::= { dhcpv6SnoopMgt 1 } dhcpv6SnoopVlan OBJECT IDENTIFIER ::= { dhcpv6SnoopMgt 2 } dhcpv6SnoopInterface OBJECT IDENTIFIER ::= { dhcpv6SnoopMgt 3 } dhcpv6SnoopBinding OBJECT IDENTIFIER ::= { dhcpv6SnoopMgt 4 } dhcpv6SnoopStatistics OBJECT IDENTIFIER ::= { dhcpv6SnoopMgt 5 } dhcpv6SnoopEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the DHCPv6 Snooping feature is enabled." ::= { dhcpv6SnoopGlobal 1 } dhcpv6SnoopBindingTableClearAction OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for clearing dhcpv6SnoopBindingTable. When this object is set to clear(2), all dynamic entries in dhcpv6SnoopBindingTable will be cleared. When this object is read, the value of this object is always noClear(1)." ::= { dhcpv6SnoopGlobal 2 } dhcpv6SnoopStatisticsClearAction OBJECT-TYPE SYNTAX INTEGER { noClear(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action for clearing dhcpSnoopStatistics. When this object is set to clear(2), statistics in dhcpSnoopStatistics will be cleared. When this object is read, the value of this object is always noClear(1)." ::= { dhcpv6SnoopGlobal 3 } -- dhcpv6SnoopVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dhcpv6SnoopVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains DHCPv6 Snooping configurations of existing VLANs." ::= { dhcpv6SnoopVlan 1 } dhcpv6SnoopVlanConfigEntry OBJECT-TYPE SYNTAX Dhcpv6SnoopVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the configuration to enable or disable DHCPv6 Snooping at each existing VLAN." INDEX { dhcpv6SnoopVlanIndex } ::= { dhcpv6SnoopVlanConfigTable 1 } Dhcpv6SnoopVlanConfigEntry ::= SEQUENCE { dhcpv6SnoopVlanIndex VlanIndex, dhcpv6SnoopVlanEnable EnabledStatus } dhcpv6SnoopVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the VLAN ID on which DHCPv6 Snooping feature is configured." ::= { dhcpv6SnoopVlanConfigEntry 1 } dhcpv6SnoopVlanEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCPv6 Snooping is enabled in this VLAN." ::= { dhcpv6SnoopVlanConfigEntry 2 } -- dhcpv6SnoopPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dhcpv6SnoopPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to configure the trust state of each port or trunk for DHCPv6 Snooping purpose." ::= { dhcpv6SnoopInterface 1 } dhcpv6SnoopPortConfigEntry OBJECT-TYPE SYNTAX Dhcpv6SnoopPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the configuration to enable or disable trust state of each port or trunk for DHCPv6 Snooping purpose." INDEX { dhcpv6SnoopPortIfIndex } ::= { dhcpv6SnoopPortConfigTable 1 } Dhcpv6SnoopPortConfigEntry ::= SEQUENCE { dhcpv6SnoopPortIfIndex InterfaceIndex, dhcpv6SnoopPortTrustEnable EnabledStatus, dhcpv6SnoopPortMaxBinding Integer32, dhcpv6SnoopPortCurrentBinding Integer32 } dhcpv6SnoopPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the port or trunk." ::= { dhcpv6SnoopPortConfigEntry 1 } dhcpv6SnoopPortTrustEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the port or trunk is trusted for DHCP Snooping purpose." ::= { dhcpv6SnoopPortConfigEntry 2 } dhcpv6SnoopPortMaxBinding OBJECT-TYPE SYNTAX Integer32(1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of binding entries of the port or trunk" ::= { dhcpv6SnoopPortConfigEntry 3} dhcpv6SnoopPortCurrentBinding OBJECT-TYPE SYNTAX Integer32(0..5) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of dynamic binding entrires learned on the port or trunk." ::= { dhcpv6SnoopPortConfigEntry 4} -- dhcpv6SnoopBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF Dhcpv6SnoopBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the DHCPv6 binding entries information learned by the device." ::= { dhcpv6SnoopBinding 1 } dhcpv6SnoopBindingEntry OBJECT-TYPE SYNTAX Dhcpv6SnoopBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the link-layer address, ia type, ia id, IPv6 address, VLAN number, interface number, lifetime." INDEX { dhcpv6SnoopBindingLinkLayerAddress, dhcpv6SnoopBindingIaType, dhcpv6SnoopBindingIaId, dhcpv6SnoopBindingIpv6Address } ::= { dhcpv6SnoopBindingTable 1 } Dhcpv6SnoopBindingEntry ::= SEQUENCE { dhcpv6SnoopBindingLinkLayerAddress MacAddress, dhcpv6SnoopBindingIaType INTEGER, dhcpv6SnoopBindingIaId Unsigned32, dhcpv6SnoopBindingIpv6Address InetAddress, dhcpv6SnoopBindingVlanIndex VlanIndex, dhcpv6SnoopBindingPortIfIndex InterfaceIndex, dhcpv6SnoopBindingLifeTime Unsigned32 } dhcpv6SnoopBindingLinkLayerAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the link-layer address of a DHCPv6 client host." ::= { dhcpv6SnoopBindingEntry 1 } dhcpv6SnoopBindingIaType OBJECT-TYPE SYNTAX INTEGER { na(3), ta(4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the IPv6 address ia type of a DHCPv6 client host. na - Non-temporary address, ta - temporary address" ::= { dhcpv6SnoopBindingEntry 2 } dhcpv6SnoopBindingIaId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the IPv6 address ia id of a DHCPv6 client host." ::= { dhcpv6SnoopBindingEntry 3 } dhcpv6SnoopBindingIpv6Address OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the IPv6 address of a DHCPv6 client host." ::= { dhcpv6SnoopBindingEntry 4 } dhcpv6SnoopBindingVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VLAN which a DHCPv6 client host belongs to." ::= { dhcpv6SnoopBindingEntry 5 } dhcpv6SnoopBindingPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port or trunk where a DHCPv6 client host connects to." ::= { dhcpv6SnoopBindingEntry 6 } dhcpv6SnoopBindingLifeTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the life time of this DHCPv6 binding." ::= { dhcpv6SnoopBindingEntry 7 } -- dhcpSnoopRecvClientPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the received number of client packets" ::= { dhcpv6SnoopStatistics 1 } dhcpSnoopSentClientPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the sent number of client packets" ::= { dhcpv6SnoopStatistics 2 } dhcpSnoopDroppedClientPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the dropped number of client packets" ::= { dhcpv6SnoopStatistics 3 } dhcpSnoopRecvServerPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the received number of server packets" ::= { dhcpv6SnoopStatistics 4 } dhcpSnoopSentServerPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the sent number of server packets" ::= { dhcpv6SnoopStatistics 5 } dhcpSnoopDroppedServerPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the dropped number of server packets" ::= { dhcpv6SnoopStatistics 6} dhcpSnoopRecvRelayPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the received number of relay packets" ::= { dhcpv6SnoopStatistics 7 } dhcpSnoopSentRelayPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the sent number of relay packets" ::= { dhcpv6SnoopStatistics 8 } dhcpSnoopDroppedRelayPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the dropped number of relay packets" ::= { dhcpv6SnoopStatistics 9} -- ip6SrcGuardMgt Table ip6SrcGuardConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Ip6SrcGuardConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the configurations to set IPv6 Source Guard at each port." ::= { ip6SrcGuardMgt 1 } ip6SrcGuardConfigEntry OBJECT-TYPE SYNTAX Ip6SrcGuardConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the configuration to set IPv6 Source Guard at each port." INDEX { ip6SrcGuardPortIfIndex } ::= { ip6SrcGuardConfigTable 1} Ip6SrcGuardConfigEntry ::= SEQUENCE { ip6SrcGuardPortIfIndex InterfaceIndex, ip6SrcGuardMode INTEGER, ip6SrcGuardMaxBinding Integer32 } ip6SrcGuardPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object idents the port which is capable of IPv6 Source Guard feature." ::= { ip6SrcGuardConfigEntry 1 } ip6SrcGuardMode OBJECT-TYPE SYNTAX INTEGER { disabled(1), srcIp(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether IPv6 Source Guard is enabled at this interface. If the value equals 1, it means IPv6 Source Guard is disabled. If the value equals 2, it means IPv6 Source Guard is enabled, and packets are filtered by checking source ip." ::= { ip6SrcGuardConfigEntry 2 } ip6SrcGuardMaxBinding OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the maximum number of bindings associated with the port." ::= { ip6SrcGuardConfigEntry 3} -- ip6SrcGuardAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF Ip6SrcGuardAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains the IPv6 Source Guard bindings information learnt by the device or configured by the user." ::= { ip6SrcGuardMgt 2 } ip6SrcGuardAddrEntry OBJECT-TYPE SYNTAX Ip6SrcGuardAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An instance contains the Mac address, binding type, IPv6 address, VLAN id, interface id, and status." INDEX { ip6SrcGuardBindingType, ip6SrcGuardBindingMacAddress, ip6SrcGuardBindingIpv6Address} ::= { ip6SrcGuardAddrTable 1 } Ip6SrcGuardAddrEntry ::= SEQUENCE { ip6SrcGuardBindingType INTEGER, ip6SrcGuardBindingMacAddress MacAddress, ip6SrcGuardBindingIpv6Address InetAddressIPv6, ip6SrcGuardBindingVlanIndex VlanIndex, ip6SrcGuardBindingPortIfIndex InterfaceIndex, ip6SrcGuardBindingStatus RowStatus } ip6SrcGuardBindingType OBJECT-TYPE SYNTAX INTEGER { static(1), dhcp6snp(2), ndsnp(3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the binding type of the associated client." ::= {ip6SrcGuardAddrEntry 1} ip6SrcGuardBindingMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the MAC address of the associated client." ::= {ip6SrcGuardAddrEntry 2} ip6SrcGuardBindingIpv6Address OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the IPv6 address of the associated client." ::= {ip6SrcGuardAddrEntry 3} ip6SrcGuardBindingVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the VLAN id of the associated client." ::= {ip6SrcGuardAddrEntry 4} ip6SrcGuardBindingPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the port of the associated client." ::= {ip6SrcGuardAddrEntry 5} ip6SrcGuardBindingStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row entry. This object issued to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device." ::= {ip6SrcGuardAddrEntry 6} -- -- trap definitions -- ecs4620Traps OBJECT IDENTIFIER ::= { ecs4620Notifications 1 } ecs4620TrapsPrefix OBJECT IDENTIFIER ::= { ecs4620Traps 0 } swPowerStatusChangeTrap NOTIFICATION-TYPE OBJECTS { swIndivPowerUnitIndex, swIndivPowerIndex, swIndivPowerStatus } STATUS current DESCRIPTION "This trap is sent when the power state changes." ::= { ecs4620TrapsPrefix 1 } swPortSecurityTrap NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "This trap is sent when the port is being intruded. This trap will only be sent when the portSecActionTrap is enabled." ::= { ecs4620TrapsPrefix 36 } swIpFilterRejectTrap NOTIFICATION-TYPE OBJECTS { trapIpFilterRejectMode, trapIpFilterRejectIp } STATUS current DESCRIPTION "This trap is sent when an incorrect IP address is rejected by the ipfilter." ::= { ecs4620TrapsPrefix 40 } swSmtpConnFailureTrap NOTIFICATION-TYPE OBJECTS { smtpServerIp } STATUS current DESCRIPTION "This trap is triggered if the SMTP system cannot open a connection to the mail server successfully." ::= { ecs4620TrapsPrefix 41 } swThermalRisingNotification NOTIFICATION-TYPE OBJECTS { switchThermalTempValue, switchThermalActionRisingThreshold } STATUS current DESCRIPTION "This trap is sent when the temperature is over the switchThermalActionRisingThreshold." ::= { ecs4620TrapsPrefix 58 } swThermalFallingNotification NOTIFICATION-TYPE OBJECTS { switchThermalTempValue, switchThermalActionFallingThreshold } STATUS current DESCRIPTION "This trap is sent when the temperature is below the switchThermalActionFallingThreshold." ::= { ecs4620TrapsPrefix 59 } tcnTrap NOTIFICATION-TYPE OBJECTS { trapTcnReason, trapTcnStackingUnitIndex, trapTcnStackingUnitRole, trapTcnStackingTplg, trapTcnStackingUpPortIndex, trapTcnStackingUpPortLinkStatus, trapTcnStackingUpPortLinkStatusChanged, trapTcnStackingDownPortIndex, trapTcnStackingDownPortLinkStatus, trapTcnStackingDownPortLinkStatusChanged } STATUS current DESCRIPTION "The variable represents the function of TCN: pushButton(1): Push button to enable the unit as the Master unit in the stack. stackingLinkDown(2): Stacking link is down. stackingLinkUp(3): Stacking link is up. hbtTimeout(4): Control packet sent from the Master through all units has timed-out. hbtError(5): Control packet sent from the Master through all units was received with errors." ::= { ecs4620TrapsPrefix 63 } -- -- ATC trap -- swAtcBcastStormAlarmFireTrap NOTIFICATION-TYPE OBJECTS { atcBcastStormIfIndex, atcBcastStormSampleType, atcBcastStormCurrentTrafficRate, atcBcastStormAlarmFireThreshold } STATUS current DESCRIPTION "When the broadcast traffic is detected as the storm, this trap will be fired." ::= { ecs4620TrapsPrefix 70 } swAtcBcastStormAlarmClearTrap NOTIFICATION-TYPE OBJECTS { atcBcastStormIfIndex, atcBcastStormSampleType, atcBcastStormCurrentTrafficRate, atcBcastStormAlarmClearThreshold } STATUS current DESCRIPTION "When the broadcast storm is detected as the normal traffic, this trap will be fired." ::= { ecs4620TrapsPrefix 71 } swAtcBcastStormTcApplyTrap NOTIFICATION-TYPE OBJECTS { atcBcastStormIfIndex, atcBcastStormSampleType, atcBcastStormCurrentTrafficRate, atcBcastStormAlarmFireThreshold, atcBcastStormTcApplyTime } STATUS current DESCRIPTION "When the ATC is activated, this trap will be fired." ::= { ecs4620TrapsPrefix 72 } swAtcBcastStormTcReleaseTrap NOTIFICATION-TYPE OBJECTS { atcBcastStormIfIndex, atcBcastStormSampleType, atcBcastStormCurrentTrafficRate, atcBcastStormAlarmClearThreshold, atcBcastStormTcReleaseTime } STATUS current DESCRIPTION "When the ATC is released, this trap will be fired." ::= { ecs4620TrapsPrefix 73 } swAtcMcastStormAlarmFireTrap NOTIFICATION-TYPE OBJECTS { atcMcastStormIfIndex, atcMcastStormSampleType, atcMcastStormCurrentTrafficRate, atcMcastStormAlarmFireThreshold } STATUS current DESCRIPTION "When the multicast traffic is detected as the storm, this trap will be fired." ::= { ecs4620TrapsPrefix 74 } swAtcMcastStormAlarmClearTrap NOTIFICATION-TYPE OBJECTS { atcMcastStormIfIndex, atcMcastStormSampleType, atcMcastStormCurrentTrafficRate, atcMcastStormAlarmClearThreshold } STATUS current DESCRIPTION "When the multicast storm is detected as the normal traffic, this trap will be fired." ::= { ecs4620TrapsPrefix 75 } swAtcMcastStormTcApplyTrap NOTIFICATION-TYPE OBJECTS { atcMcastStormIfIndex, atcMcastStormSampleType, atcMcastStormCurrentTrafficRate, atcMcastStormAlarmFireThreshold, atcMcastStormTcApplyTime } STATUS current DESCRIPTION "When the ATC is activated, this trap will be fired." ::= { ecs4620TrapsPrefix 76 } swAtcMcastStormTcReleaseTrap NOTIFICATION-TYPE OBJECTS { atcMcastStormIfIndex, atcMcastStormSampleType, atcMcastStormCurrentTrafficRate, atcMcastStormAlarmClearThreshold, atcMcastStormTcReleaseTime } STATUS current DESCRIPTION "When the ATC is released, this trap will be fired." ::= { ecs4620TrapsPrefix 77 } stpBpduGuardPortShutdownTrap NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "This trap will be sent when an interface is shut down because of BPDU guard." ::= { ecs4620TrapsPrefix 91} swLoopbackDetectionTrap NOTIFICATION-TYPE OBJECTS { staLoopbackDetectionPortIfIndex } STATUS current DESCRIPTION "This trap will be sent when loopback BPDUs have been detected." ::= { ecs4620TrapsPrefix 95} networkAccessPortLinkDetectionTrap NOTIFICATION-TYPE OBJECTS { ifIndex, ifOperStatus, networkAccessPortLinkDetectionMode, networkAccessPortLinkDetectionAciton } STATUS current DESCRIPTION "This trap is sent when a networkAccessPortLinkDetection event is triggered." ::= { ecs4620TrapsPrefix 96 } dot1agCfmMepUpTrap NOTIFICATION-TYPE OBJECTS { dot1agCfmMepDbRMepIdentifier } STATUS current DESCRIPTION "This trap is sent when a new remote MEP is discovered." ::= { ecs4620TrapsPrefix 97 } dot1agCfmMepDownTrap NOTIFICATION-TYPE OBJECTS { dot1agCfmMepDbRMepIdentifier } STATUS current DESCRIPTION "This trap is sent when port status or interface status TLV received from remote MEP indicates it is not up." ::= { ecs4620TrapsPrefix 98 } dot1agCfmConfigFailTrap NOTIFICATION-TYPE OBJECTS { dot1agCfmMepIdentifier } STATUS current DESCRIPTION "This trap is sent when a MEP receives a CCM with MPID which already exists on the same MA in this switch." ::= { ecs4620TrapsPrefix 99 } dot1agCfmLoopFindTrap NOTIFICATION-TYPE OBJECTS { dot1agCfmMepIdentifier } STATUS current DESCRIPTION "This trap is sent when a MEP receives its own CCMs." ::= { ecs4620TrapsPrefix 100 } dot1agCfmMepUnknownTrap NOTIFICATION-TYPE OBJECTS { dot1agCfmMepIdentifier } STATUS current DESCRIPTION "This trap is sent when a CCM is received from an unexpected MEP." ::= { ecs4620TrapsPrefix 101 } dot1agCfmMepMissingTrap NOTIFICATION-TYPE OBJECTS { dot1agCfmMepDbRMepIdentifier } STATUS current DESCRIPTION "This trap is sent when the cross-check enable timer expires and no CCMs were received from an expected (configured) MEP." ::= { ecs4620TrapsPrefix 102 } dot1agCfmMaUpTrap NOTIFICATION-TYPE OBJECTS { dot1agCfmMaIndex } STATUS current DESCRIPTION "This trap is sent when all expected remote MEPs are up." ::= { ecs4620TrapsPrefix 103 } autoUpgradeTrap NOTIFICATION-TYPE OBJECTS { fileCopyFileType, trapAutoUpgradeResult, trapAutoUpgradeNewVer } STATUS current DESCRIPTION "This trap is sent when auto upgrade is executed." ::= { ecs4620TrapsPrefix 104 } swCpuUtiRisingNotification NOTIFICATION-TYPE STATUS current DESCRIPTION "This notification indicates that the CPU utilization has risen from cpuUtiFallingThreshold to cpuUtiRisingThreshold." ::= { ecs4620TrapsPrefix 107 } swCpuUtiFallingNotification NOTIFICATION-TYPE STATUS current DESCRIPTION "This notification indicates that the CPU utilization has fallen from cpuUtiRisingThreshold to cpuUtiFallingThreshold." ::= { ecs4620TrapsPrefix 108 } swMemoryUtiRisingThresholdNotification NOTIFICATION-TYPE STATUS current DESCRIPTION "This notification indicates that the memory utilization has risen from memoryUtiFallingThreshold to memoryUtiRisingThreshold." ::= { ecs4620TrapsPrefix 109 } swMemoryUtiFallingThresholdNotification NOTIFICATION-TYPE STATUS current DESCRIPTION "This notification indicates that the memory utilization has fallen from memoryUtiRisingThreshold to memoryUtiFallingThreshold." ::= { ecs4620TrapsPrefix 110 } dhcpRogueServerAttackTrap NOTIFICATION-TYPE OBJECTS { trapDhcpClientPortIfIndex, trapDhcpServerIpAddress, trapDhcpServerMacAddress } STATUS current DESCRIPTION "This trap is sent when receiving a DHCP packet from a rogue server." ::= { ecs4620TrapsPrefix 114 } macNotificationTrap NOTIFICATION-TYPE OBJECTS { trapIfIndex, trapVlanId, trapVarMacAddr, trapMacNotifyAction } STATUS current DESCRIPTION "This trap is sent when there are changes of the dynamic MAC addresses on the switch." ::= { ecs4620TrapsPrefix 138 } lbdDetectionTrap NOTIFICATION-TYPE OBJECTS { trapIfIndex, trapVlanId } STATUS current DESCRIPTION "This trap is sent when a loopback condition is detected by LBD." ::= { ecs4620TrapsPrefix 141 } lbdRecoveryTrap NOTIFICATION-TYPE OBJECTS { trapIfIndex } STATUS current DESCRIPTION "This trap is sent when a recovery is done by LBD." ::= { ecs4620TrapsPrefix 142 } sfpThresholdAlarmWarnTrap NOTIFICATION-TYPE OBJECTS { trapSfpThresholdAlarmWarnIfIndex, trapSfpThresholdAlarmWarnType } STATUS current DESCRIPTION "This trap is sent when the sfp's A/D quantity is not within alarm/warning thresholds." ::= { ecs4620TrapsPrefix 189 } -- -- UDLD trap -- udldPortShutdownTrap NOTIFICATION-TYPE OBJECTS { udldPortIndex, trapUdldPortShutdownReason } STATUS current DESCRIPTION "This trap is sent when the port is shut down by UDLD." ::= { ecs4620TrapsPrefix 192 } userAuthenticationFailureTrap NOTIFICATION-TYPE OBJECTS { trapVarLoginUserName, trapVarSessionType, trapVarLoginInetAddressType, trapVarLoginInetAddress } STATUS current DESCRIPTION "This trap will be triggered if authentication is fail." ::= { ecs4620TrapsPrefix 199 } userAuthenticationSuccessTrap NOTIFICATION-TYPE OBJECTS { trapVarLoginUserName, trapVarSessionType, trapVarLoginInetAddressType, trapVarLoginInetAddress } STATUS current DESCRIPTION "This trap will be triggered if authentication is successful." ::= { ecs4620TrapsPrefix 200 } loginTrap NOTIFICATION-TYPE OBJECTS { trapVarLoginUserName, trapVarSessionType, trapVarLoginInetAddressType, trapVarLoginInetAddress } STATUS current DESCRIPTION "This trap is sent when user login." ::= { ecs4620TrapsPrefix 201 } logoutTrap NOTIFICATION-TYPE OBJECTS { trapVarLoginUserName, trapVarSessionType, trapVarLoginInetAddressType, trapVarLoginInetAddress } STATUS current DESCRIPTION "This trap is sent when user logout." ::= { ecs4620TrapsPrefix 202 } fileCopyTrap NOTIFICATION-TYPE OBJECTS { trapVarLoginUserName, trapVarSessionType, trapVarLoginInetAddressType, trapVarLoginInetAddress, fileCopySrcOperType, fileCopySrcFileName, fileCopyDestOperType, fileCopyDestFileName, fileCopyFileType, fileCopyUnitId, fileCopyStatus, fileCopyServerInetAddressType, fileCopyServerInetAddress } STATUS current DESCRIPTION "This trap is sent when file copy is executed. If the copy action is triggered by system, the login user information(trapVarLoginUserName/ trapVarSessionType/trapVarLoginInetAddressType/ trapVarLoginInetAddress) will be null value." ::= { ecs4620TrapsPrefix 208 } userauthCreateUserTrap NOTIFICATION-TYPE OBJECTS { userAuthUserName } STATUS current DESCRIPTION "This trap is sent when create user account." ::= { ecs4620TrapsPrefix 209 } userauthDeleteUserTrap NOTIFICATION-TYPE OBJECTS { userAuthUserName } STATUS current DESCRIPTION "This trap is sent when delete user account." ::= { ecs4620TrapsPrefix 210 } userauthModifyUserPrivilegeTrap NOTIFICATION-TYPE OBJECTS { userAuthUserName, userAuthPrivilege } STATUS current DESCRIPTION "This trap is sent when modify user privilege." ::= { ecs4620TrapsPrefix 211 } cpuGuardControlTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "This trap is sent when CPU utilization rises above the high-watermark first time or when CPU utilization rises from below the low-watermark to above the high-watermark." ::= { ecs4620TrapsPrefix 213 } cpuGuardReleaseTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "This trap is sent when CPU utilization falls from above the high-watermark to below the low-watermark." ::= { ecs4620TrapsPrefix 214 } stackingUnitInsertRemoveTrap NOTIFICATION-TYPE OBJECTS { trapStackingUnitIndex, trapStackingUnitInsertRemove } STATUS current DESCRIPTION "This trap is sent when stacking unit is inserted or removed." ::= { ecs4620TrapsPrefix 244 } END