+----------------------------------+ | ECS4210-28T/P |ECS4210-12T/P +----------------------------------+ "ECS4210-28-.bix" is a universal opcode shared among ECS4210-28T and ECS4210-28P. PID and individual BIDs are listed below. ECS4210-28T PID = 421, BID = 0, ECS4210-28P PID = 421, BID = 1, ECS4210-12T PID = 438, BID = 4, ECS4210-12P PID = 435, BID = 5, FAN 8200 rpm fan detection ECS4210-12P PID = 435, BID = 6, FAN 9000 rpm fan detection ================ Chip limitation ================ 1. ARP packets are trapped into CPU by ACL rule, that is mean user can not use ACL rule to have action on the ARP packets. 2. Wen TCAM priority is IPv4 MAC IPv6 and IPSG is SIP mode, PPPoE packets with un-compressed data will be dropped. V1.0.0.8 (Build 2013/01/31) --------------------------- ES4328QV-FLF-ZZ-00157 mac-vlan can't work correclty with DHCP snooping ES4328QV-FLF-ZZ-00159 Add to port to vlan 2 causing CPU utilization become 100% ES4328QV-FLF-ZZ-00160 send the traffic with vlan 2, show mac-address table can't find the entry ES4312QV-HPoE-FLF-ZZ-00005 Web: Show ACL TCAM on Web UI, all the information will display "Undefined". ES4312QV-HPoE-FLF-ZZ-00105 remove sfp-forced 100fx from CLI command. ES4312QV-HPoE-FLF-ZZ-00106 can remove protocol vlan but show failed in CLI. ES4312QV-HPoE-FLF-ZZ-00107 enable ip source-guard will block the traffic V1.0.0.9 (Build 2013/03/1) --------------------------- ES4328QV-FLF-ZZ-00162 Interface > Trunk > Dynamic (Configure Trunk - Configure) - page not displayed ES4328QV-FLF-ZZ-00163 lights wrong ports on panel graphic ES4328QV-FLF-ZZ-00170 MAC-Mirror: After remove MAC mirror entry, the mirrored port still recieve data. ES4328QV-FLF-ZZ-00171 WEB: The front pannel port information dispalyed on WEB page is incorrect. ES4328QV-FLF-ZZ-00184 Policy map not allow mixing MAC, IPv4, IPv6 extended, and IPv6 standard rules together ES4312QV-HPoE-FLF-ZZ-00006 Web: ACL Clear Hardware Counter button and Hit Count are not in correct position. ES4312QV-HPoE-FLF-ZZ-00007 Web: ACL Configure Interface page will disappear when we change "Action:" from other option and reture to "Configure" again. ES4312QV-HPoE-FLF-ZZ-00008 Web: RJ45 Logo on front penal are reversed ES4312QV-HPoE-FLF-ZZ-00009 Web: ACL "Action:" selection will not work when change the action from Configure->Add Mirror-> ES4312QV-HPoE-FLF-ZZ-00011 Web: Site MAP information can't match what really support on Management Panel. ES4312QV-HPoE-FLF-ZZ-00013 Auto IP: CLI supports Auto IP function, but Web UI doesn't support it. ES4312QV-HPoE-FLF-ZZ-00014 Ping: Ping Host via Web UI, sometimes it will have timeout but result still shows 100% received and 0% packet lost. ES4312QV-HPoE-FLF-ZZ-00015 Ping: Ping Host via Web UI, sometimes the Maximum response time value is incorrect - not match the real response time value. ES4312QV-HPoE-FLF-ZZ-00028 MVR Web: It display "404 Not Found" when query some port to show MVR static group. ES4312QV-HPoE-FLF-ZZ-00033 Diffserv:Bind trtcm-blind of policy map in Port's ingress. CLI will display error message. ES4312QV-HPoE-FLF-ZZ-00035 IPv6 Ping : the packet size is Not same in CLI <0-1500> & WEB UI (32-512) ES4312QV-HPoE-FLF-ZZ-00040 Diffserv:Bind trtcm-aware of policy map in Port's ingress. Diffserv cannot work and CLI will display error message. ES4312QV-HPoE-FLF-ZZ-00041 UserAuthRemote:DUT logging by Tacacs server, but "Authentication Sequence" can not changed on Web. ES4312QV-HPoE-FLF-ZZ-00042 partner's LLDP-MED information. ES4312QV-HPoE-FLF-ZZ-00048 CoS: Trust mode description is incorrect. ES4312QV-HPoE-FLF-ZZ-00070 Cluster:The commander didn't access to the member from web or CLI when setting cluster from web ES4312QV-HPoE-FLF-ZZ-00084 LACP web: The page of dynamic trunk configuration is empty,so it can't set via web. ES4312QV-HPoE-FLF-ZZ-00118 Statistics: Plug in and pull out this SFP module from Port11, DUT return error message. ES4312QV-HPoE-FLF-ZZ-00123 PoE: The "PoE Power Consumption" value can over "PoE Maximum Available Power". ES4312QV-HPoE-FLF-ZZ-00127 qinq access port will strip stag and ctag ES4328QV-FLF-ZZ-00184 Policy map not allow mixing MAC, IPv4, IPv6 extended, and IPv6 standard rules together V1.0.0.10 (Build 2013/03/08) --------------------------- jumbo frame size set rate limit please add pps support ES4312QV-HPoE-FLF-ZZ-00131 ACL: New feature for shared ACL rule in different ports when these rules are the identical. ES4312QV-HPoE-FLF-ZZ-00132 can't shutdown individually, show trunk member could not be configured. ES4312QV-HPoE-FLF-ZZ-00124 "Terminal lenght" does not work properly ES4328QV-FLF-ZZ-00183 front pannel display issue in web page V1.0.0.11 (Build 2013/03/22) --------------------------- ES4328QV-FLF-ZZ-00176 AMTR: DUT return error message when enable this sticky-dynamic on port/VLAN. ES4328QV-FLF-ZZ-00181 Change header to MAC Address > Extended MAC Security ES4328QV-FLF-ZZ-00182 remove sh loop internal interface ES4328QV-FLF-ZZ-00196 trunk_id for DEV_AMTRDRV_SetMovableStaticTbIEntryDevice() ES4328QV-FLF-ZZ-00197 PoE status: LED flashing Amber ES4328QV-FLF-ZZ-00198 error message on DIAG#swinit ES4312QV-HPoE-FLF-ZZ-00133 [Enhancement] Support PPPoE type in Protocol VLAN ES4328QV-FLF-EC-00004 Traffic segementation support multiple session V1.0.0.12 (Build 2013/04/12) --------------------------- ES4328QV-FLF-ZZ-00134 DHCP Option Relay82:Setting DHCP Relay Server on CLI,but it did not display on Web ES4312QV-HPoE-FLF-ZZ-00125 DiffServ-WEB: Can't create TRTCM-COLOR-AWARE/BLIND entry from WEB UI. ES4328QV-FLF-ZZ-00200 TW Steve made some update the web help page, shall sync/update V1.0.0.13 (Build 2013/04/16) --------------------------- ES4312QV-HPoE-FLF-EC-00043 have no way to set admin-key 4 for port-channel V1.0.0.14 (Build 2013/05/24) --------------------------- ES4312QV-HPoE-FLF-EC-00049 Remove the function when overload of a port to shutdown POE admin of a port and When power consumption is not reasonable, display as 0mw. ES4312QV-HPoE-FLF-EC-00019 Cluster:The commander didn't access to the member from web or CLI when setting cluster from web ES4312QV-HPoE-FLF-ZZ-00137 ACL: Binding and unbinding will cause the rule to be wrong priority set. ES4328QV-FLF-EC-00033 dhcp relay option 82 in cli, but not in web ES4328QV-FLF-EC-00061 1QVLAN: When we join the member ports to same VID range, this result is inconsistent between WEB and CLI. ES4328QV-FLF-EC-00075 L2SW: The DUT can transceiver the 13000 of packet size that is untagged packet ES4328QV-FLF-EC-00079 L2SW: The DUT can transceiver the 13004 of packet size with VLAn tagged ES4328QV-FLF-EC-00083 LLDP: After enable SNMP Notification on WEB, an exception occurs ES4328QV-FLF-EC-00099 Port mirror: The 1000Base-X SFP Module mirroring port doesn't receive all TX/RX/Both packets from the mirrored switch port. ES4312QV-HPoE-FLF-EC-00028 DoS: The DUT could not set the MAX allowance rate value of DoS TCP/UPD/ICMP/Echo correctly via SNMP. customer issue vlan tag cfi index is set to 1 MFG issue add wire-speed workaround to use 2 packets at a time for a loop test instead of only 1 V1.0.0.15 (Build 2013/05/29) --------------------------- ES4312QV-HPoE-FLF-EC-00047 Phase 2 enhancement IGMP RADIUS Authentication new feature enhancement VLAN ACL V1.0.0.16 (Build 2013/06/04) --------------------------- ASIC refinement improve the CPU utilization & reduce the CPU occupication of the access the MIB counter ES4312QV-HPoE-FLF-EC-00018 Cluster:After reboot the DUT, show cluster member doesn't display description information. ES4328QV-FLF-ZZ-00168 comments on spelling in web interface V1.0.0.17 (Build 2013/08/02) --------------------------- Enhancement: Green Saving Technology Enhancement: select QinQ Enhancement: set QinQ access mode and tpid on one port will not change to all port Enhancement: vlan translation function Enhancement: Traffic segementation support multiple session V1.0.0.18 (Build 2013/09/12) --------------------------- ES4312QV-HPoE-FLF-EC-00008 MAC Isolation : Can't configure MAC isolation function via SNMP ES4328QV-FLF-EC-00027 AMTR: DUT send out the HWSecurityIntrusionMACTrap with incorrect OID. ES4312QV-HPoE-FLF-EC-00075 Mistake in reading information over SNMP - local VLANs are missing ES4328QV-FLF-EC-00118 Diffserv: The EBS field can be configured when meter mode is TRTCM on web. ES4328QV-FLF-EC-00120 DHCP-SNP: We can enable DHCP Snooping on VLAN 4094, but DUT deny this same setting from WEB ES4328QV-FLF-EC-00169 compactness of vlan in vlan data base or running config ES4328QV-FLF-38IK-00002 support mac-vlan OUI(vendors code) configuration ES4328QV-FLF-38IK-00026 ES4328-Series.mib won't compile under EliteView ES4328QV-FLF-EC-00154 CoS: Set "prioIfClassificationModeStatus" cause HTTP/SNMP/Telnet/PING no response. ES4312QV-HPoE-FLF-EC-00071 dhcp snooping and dhcp relay can't work at the same time ES4328QV-FLF-ZZ-00209 [Trunk/PacketToCpu]Incorrect rx port information in lan if the frame comes from a trunk member (wire-speed loopback fail) ES4328QV-FLF-EC-00171 configure LACP will cause switch hang ES4328QV-FLF-EC-00172 show running-config interface is empty ES4328QV-FLF-EC-00170 STP work incorrectly if LACP is enabled ES4328QV-FLF-EC-00163 TrafficSeg: "2.Configure Session" shows blank page on WebUI. ES4328QV-FLF-38IK-00135 MVR-MIB: Size list in properties of mvrVlanId is wrong. ES4328QV-FLF-EC-00168 Waiting for long time to show running if there are 4K vlans. V1.0.0.19 (Build 2013/10/21) --------------------------- ES4328QV-FLF-EC-00065 1QVLAN: After we join all ports to maximum VLANs; CLI is halted and show exception. ES4328QV-FLF-EC-00026 AMTR: DUT send out the PortMoveTrap with incorrect OID. ES4328QV-FLF-38IK-00137 L2SW: We cannot clear the dynamic MAC of VLAN 4094 by CLI. ES4328QV-FLF-38IK-00155 Diffserv-MIB: Can't display IPv6 ace information by SNMP. ES4328QV-FLF-38IK-00162 TACACS-Acct: All MIB sub-Objects of aaaMgt cannot work. ES4328QV-FLF-38IK-00163 Diffserv-MIB: Got commit failed when we set diffServPortPolicyMapIndex with with instance 29~40. ES4328QV-FLF-38IK-00164 Diffserv-MIB: Can't bind ip/ipv6/mac acl to port by SNMP. ES4328QV-FLF-38IK-00168 DiffServ: No information for Excess Information Rate and Excess Burst Size on diffServMeterTable. ES4328QV-FLF-38IK-00176 Ping: Perform remote ping with hostname via web always timeout ES4328QV-FLF-38IK-00180 UI: kill admin user account, but it will create again after reboot. phase 2 enhancement MLDv1 / MLDv2 snooping ES4312QV-FLF-EC-00030 Dynamic Provsion: When DUT has failed to get the remote configuration file, it should not retry this provsion continually. ES4312QV-HPoE-FLF-EC-00074 show cable-diagnostics interface is empty V1.0.0.20 (Build 2013/11/1) --------------------------- ES4312QV-FLF-EC-00030 Dynamic Provsion: When DUT has failed to get the remote configuration file, it should not retry this provsion continually. ES4312QV-FLF-EC-00050 LLDP: Device console lock after save running configtion to startup configuration. ES4328QV-FLF-EC-00186 Error free opreation in dev_nicdrv_gateway.c cause CLI hang after running several hours in customer site.. V1.0.0.21 (Build 2013/12/5) --------------------------- ES4328QV-FLF-EC-00016 IPv6DHCPClient:When IPv6 client send packets to get IP to server, but server did not get any packets. ES4328QV-FLF-EC-00043 System: When we upgrade this image from TFTP; DUT generate Rise Trap and this CPU utilization is 100%. ES4328QV-FLF-EC-00045 System: When this spanning-tree topology is changed, this DUT is unstable. ES4328QV-FLF-EC-00053 ACL: Behavior is wrong when delete all ACE in some ACE web page. ES4328QV-FLF-EC-00055 1QVLAN: When we copy running configuration to sartup, DUT generate this Rise Trap and CPU utilization 100%. ES4328QV-FLF-EC-00056 1QVLAN: When we save running configuration and inject mutiple VLAN traffic; this ping session always is timeout. ES4328QV-FLF-EC-00060 DAI: Got same result after change arp rate limit value. ES4328QV-FLF-EC-00063 DAI: DAI log message was generated over configuration value. ES4328QV-FLF-EC-00064 DAI: DAI log can't record to system log. ES4328QV-FLF-EC-00067 CoS: After change phb queue mapping, the output stream reate didn't change. ES4328QV-FLF-EC-00068 1QVLAN: After we change this native VLAN state to Active from Suspended, DUT does not forward untagged packets to defaule VLA ES4328QV-FLF-EC-00069 RSTP: The bpdu filter is disabled when enabled the BPDU filter with per port or port-channel and save /reboot. ES4328QV-FLF-EC-00073 IPv6-AddrConfig: Times of DAD Attempts are always one by default setting. ES4328QV-FLF-EC-00074 HTTP: HTTP/HTTPS port number can not be set to 1. ES4328QV-FLF-EC-00085 DHCP-OptionRelay82: DUT should not forward this Reply packets to Client from relay agent. ES4328QV-FLF-EC-00090 MVR: Static MVR group can not be listed when we change MVR VLAN. ES4328QV-FLF-EC-00091 MVR: MVR multicast traffic input from inactive source port can be forwarded to registered receiver port. ES4328QV-FLF-EC-00093 LLDP: LLDP with MED PDU not follow fast start counter. ES4328QV-FLF-EC-00095 LLDP: Can't sent 802.3 Power Via MDI TLV and LLDP-MED extension PoE TLV. ES4328QV-FLF-EC-00100 IGMPSNP: Display of dynamic route port expire is wrong when expire is set more than 3600 seconds. ES4328QV-FLF-EC-00109 Diffserv: The output ratio didn't follow cos-dhcp mapping after set cos to different value. ES4328QV-FLF-EC-00110 Diffserv: The service policy for egress is not work. ES4328QV-FLF-EC-00113 DAI: Enable DAI globally, the arp packet will be dropped. ES4328QV-FLF-EC-00122 MAC-BasedVLAN: The mac-address table will fill out the incorrect VLAN ID when remove a created mac-address of MAC-BasedVLAN ES4328QV-FLF-EC-00126 DHCP-SNP: DUT get get IP address, but this binding information is incorrect. ES4328QV-FLF-EC-00131 Voice VLAN: When we fail to delete this default OUI rule, this voice vlan member is removed. ES4328QV-FLF-EC-00132 RSTP: The DUT doesn't send the loopback detection packet when enable the spanning-tree loopback detection with per port. ES4328QV-FLF-EC-00133 RSTP: The DUT doesn't send the loopback detection packet when enable the spanning-tree loopback detection with per port. ES4328QV-FLF-EC-00136 DHCPv6 CIient: DUT cannot get DHCP6 address from server. ES4328QV-FLF-EC-00137 DHCPv6 CIient: DUT cannot display DHCP6 setting. ES4328QV-FLF-EC-00142 Diffserv: Create maximum class-map in policy map and bind to physical port, traffic can't be forwarded. ES4328QV-FLF-EC-00166 DAI: DUT cannot save mutiple additional validation type with source and destination MAC. ES4328QV-FLF-EC-00167 DAI: This maximum length of filter name should be matched to ACL name. ES4328QV-FLF-EC-00172 show running-config interface is empty ES4328QV-FLF-EC-00174 [XC] CLI will crash if sending the specific LLDP frames into switch ES4328QV-FLF-EC-00176 There is some command missing in running-config ES4328QV-FLF-EC-00181 NTP: Can't save NTP authentication-key after reboot. ES4328QV-FLF-EC-00188 ping fail caused by set the CFI index as 1 ES4328QV-FLF-EC-00191 banner configuration didn't show in sh run ES4328QV-FLF-EC-00194 bind service-policy on port will have strange message ES4328QV-FLF-EC-00199 [ECS4210-28T] "switchport acceptable-frame-typs tagged" drop "untag" BPDU ES4312QV-HPoE-FLF-EC config igmp profile there are strange range in show run ES4312QV-FLF-EC-00053 Statistics: The interface counter display incorrect value. ES4312QV-HPoE-FLF-EC-00055 System: When we inject ARP packets with packet-rate over 20 fps, DUT generates this Rise Trap and CPU utilization 100%. ES4328QV-FLF-EC-00197 System: DUT changes this spanning-tree topology continuously. V1.0.0.21 for ES4312QV-FLF-EC (Build 2013/12/13) --------------------------- ES4312QV-FLF-EC-00027 Wire-speed loopback fail on ES4312QV-FLF-EC and display link status on wsextlb V1.0.0.22 (Build 2013/12/17) --------------------------- ES4328QV-FLF-EC-00200 Enhancement :IGMP_auth: report shall not forwarded to mrouter port before authenticate ES4328QV-FLF-EC-00203 Enhancement :aging time is 7200 secs V1.0.0.23 for ES4312QV-HPoE-FLF-EC, only this model have this issue (Build 2013/1/6) --------------------------- ES4312QV-HPoE-FLF-EC-00085 Configuration File: After we save running configuration and rebooting, DUT lose all V1.0.0.24 (Build 2014/1/23) --------------------------- ES4328QV-FLF-EC-00224 inject the bigger traffic to SFP port when booting will loss management ES4328QV-FLF-EC-00225 authentication is failed. ES4328QV-FLF-38IK-00184 Lose DHCP relay function V1.0.0.25 (Build 2014/1/27) for ES4312QV-HPoE-FLF-EC, only this model have this issue --------------------------- ES4312QV-HPoE-FLF-EC-00107 IPv6_AddrConfig: The CLI crashed when the IPv6 address autoconfig was enabled. V1.0.0.26 (Build 2014/3/6) --------------------------- ES4328QV-FLF-EC-00202 4210-28T TCAM overload ES4328QV-FLF-EC-00229 [TCAM] New feature for dynamic TCAM allocation. ES4312QV-FLF-EC-00086 QinQ configuration. Management loss issue V1.0.0.27 (Build 2014/3/14) --------------------------- ES4328QV-FLF-EC-00233 switch doesn't reply ARP request when service-policy apply on interface ES4328QV-FLF-EC-00227 failed to remove vlan when enable vlan-trunking on interface ES4328QV-FLF-EC-00228 multicast data cannot go to client while "ip source-guard sip/sip-mac" is enabled ES4328QV-FLF-EC-00230 DHCPv6 CIient: After we restart DHCP client; CLI is halted and generate exception. ES4328QV-FLF-EC-00238 ACL: No information when show the TCAM allocation. ES4328QV-FLF-EC-00239 ACL: No "show tcam priority" command on CLI. ES4328QV-FLF-EC-00240 ACL: No "tcam priority" command on CLI. V1.0.0.28 (Build 2014/3/26) --------------------------- ES4328QV-FLF-EC-00232 IPv6_DAD: DAD attempts can not be set successfully. ES4328QV-FLF-EC-00245 MLD-SNP: DUT console lock after enable MLD snooping. If the Web cgi need to printf out too much, maybe it will over-write the memory. V1.0.0.29 (Build 2014/3/27) --------------------------- ES4328QV-FLF-EC-00199 [ECS4210-28T] "switchport acceptable-frame-typs tagged" drop "untag" BPDU (re-open issue) loader v1.0.0.9 (Build 2014/4/17 ) ES4328QV-FLF-EC-00256 Loader: backdoor passwd doesn't be encrypted V1.0.0.30 (obsolete) --------------------------- V1.0.0.31 (Build 2014/4/24) --------------------------- ES4328QV-FLF-EC-00196 [enhancement] non-STP loopback detection refinement ES4328QV-FLF-EC-00251 Flow Control Type is automatically active when flow control disabled on SFP V1.0.0.32 (Build 2014/5/19) --------------------------- ES4312QV-HPoE-FLF-EC-00113 ACL: The DUT will crash when repeat to set the service-policy on the same port. ES4328QV-FLF-EC-00255 ECS4210-28T IPSG sip-mac mode and Service Policy can not work together ES4328QV-FLF-EC-00258 switch will drop DHCPACK packets when server reply DHCPACK to DHCPINFORM V1.0.0.33 (Build 2014/6/9) --------------------------- ES4312QV-FLF-EC-00093 [ECS4210-12T] RSTP with QinQ issue ES4328QV-FLF-EC-00201 the switch show error message "L_MM_Free():invalid buffer" V1.0.0.34 (Build 2014/6/26) --------------------------- ES4312QV-FLF-EC-00092 MVR forward 2 queries to MVR recevier port , if MVR source port receives ONLY ONE query. ES4328QV-FLF-EC-00260 support DDM via SNMP V1.0.0.36 (Build 2014/7/31) --------------------------- ES4328QV-FLF-EC-00262 ECS4210-28T/ECS3510-28T DHCP SNP trust port without setting DAI trust may fowards ARP packets to others ports. ES4328QV-FLF-EC-00265 mvr proxy switching sends IGMPv1 report with source ip 0.0.0.0 ES4328QV-FLF-EC-00266 IPSG function will drop PPPoE packets ES4328QV-FLF-EC-00268 After copy TFTP file to running-config,reload will show fail message. ES4328QV-FLF-EC-00269 Enable/Disable ACL on port will have error message : Free PCL(38) from device failed ES4328QV-FLF-EC-00270 ACL will failed to bind on port after repeat enable/disable ES4328QV-FLF-ZZ-00217 The queue that use by rule to trapped my target ARP is not as expected ES4328QV-FLF-EC-00271 DNS fragment packet cause leakage ES4328QV-FLF-38IK-00198 upload firmware with incorrect file type via FTP,it will let system crash V1.0.0.37 (Build 2014/8/28) --------------------------- ES4328QV-FLF-EC-00272 Adding a command that allow user to disable HW reset button on CLI and SNMP ES4328QV-FLF-EC-00274 ECS4210-28T cable diag. problems ES4328QV-FLF-EC-00275 remove the block status of STP loopback detection action in cli,snmp V1.0.0.38 (Build 2014/9/2) --------------------------- ES4328QV-FLF-EC-00278 STP loopback detection action change default value from block to shutdown V1.0.0.39 (Build 2014/9/29) --------------------------- ES4328QV-FLF-38IK-00198 upload firmware with incorrect file type via FTP,it will let system crash ES4328QV-FLF-EC-00273 there are 3 fans in show system command on fanless model ES4328QV-FLF-EC-00278 STP loopback detection action change default value from block to shutdown ES4328QV-FLF-EC-00279 add new option that allow user to disable HW reset button on Web ES4328QV-FLF-EC-00276 remove the block status of STP loopback detection action in Web V1.0.0.40 (Build 2014/10/9) --------------------------- ES4328QV-FLF-EC-00281 DAI is still global command. but we have to configure trust port that should not inspect ARP packet V1.0.0.41 (Build 2014/10/24) --------------------------- ES4328QV-FLF-38IK-00201 DHCP-OptionRelay82: DUT should not forward this Reply packets to Client from relay agent. ES4328QV-FLF-38IK-00202 HCP-OptionRelay82: When we configure this DUT as Relay agent, it should not forward orignial Request to server. ES4328QV-FLF-EC-00282 ECS4210-28T(1.0.0.38) SNMP OID - static MAC problem ES4328QV-FLF-EC-00264 [VIA] Swtich won't sync the NTP server after rebooting. V1.0.0.42 (Build 2014/11/22) --------------------------- ES4328QV-FLF-EC-00283 show mac-addres-table address "Cx-xx-xx-xx-xx-xx" will run command show mac-addres-table count ES4328QV-FLF-EC-00284 set source port mode as dynamic, all source port could receive multicast even there is no join host ES4328QV-FLF-EC-00285 failed to set port cababilities by snmp V1.0.0.43 (Build 2014/12/9) --------------------------- ES4328QV-FLF-EC-00286 WEB GUI will get incorrect time-range rule setting ES4328QV-FLF-EC-00287 LACP port connect to normal port then will have exception occurs V1.0.0.44 (Build 2015/1/19) --------------------------- ES4328QV-FLF-EC-00288 switch keep sending IGMP membership report even there are no client send the report V1.0.0.45 (Build 2015/1/29) --------------------------- ES4328QV-FLF-EC-00289 loopback-detection didn't work with port security V1.0.0.46 (Build 2015/2/13) --------------------------- ES4312QV-FLF-EC-00095 Remove the OAM feature V1.0.0.47 (Build 2015/5/25) --------------------------- ES4328QV-FLF-EC-00293 switch didn't forward arp packets when first byte and last 2 bytes of management ip match dst host ip